ignition SSANGYONG NEW ACTYON SPORTS 2012 Workshop Manual

02-42
The door lock system outputs "LOCK" when the vehicle speed maintains over 30 km/h.
However, it doesn't output "LOCK" when all doors are locked or failed.
If any of doors is unlocked after outputting "LOCK" in step 1, outputs "LOCK" up to 5 times
(except step (1)) at the interval of one second.
If any of doors is unlocked after 5 times of "LOCK" outputs, the door
(driver's/passenger's/rear) is regarded as "FAIL".
If the door that was regarded as fail is changed (UNLOCK to LOCK), it will be recognized
as a normal one.
If any door is regarded as FAIL, the auto door lock function does not work. (if it is
occurred when the vehicle speed is over 30 km/h, the auto door lock output does not
occur even if the vehicle speed falls below 30 km/h and accelerates again to over 30
km/h.) Nonetheless, the central door lock function works properly.
When the system receives "UNLOCK" signal from a door switch, it outputs "LOCK" signals
5 times. If additional "LOCK" signal from another door switch is detected during the
period, the system outputs five "LOCK" signals 5 times for the switch.
The door lock system outputs "UNLOCK" automatically if the "LOCK" output conditions are
established by this function or the key is cycled (IGN=OFF) (even when there is no "LOCK"
output while the vehicle speed maintains over 30 km/h under lock condition).
(If the LOCK condition is established with the ignition switch ON, the system outputs
UNLOCK signal unconditionally when turning the ignition switch to OFF position.)
However, when the ignition key is turned to "OFF" position, the lock output conditions will
be cancelled.
The "FAIL" condition of the door will be erased when the ignition key is turned to "OFF"
position. 1.
2.
3.
4.
5.
6.
7.
8. ▶Auto Door Lock
T2: 0.5 s
(*1) LOCK: Driver's & Passenger's & Rear door & = Lock

02-438710-01
▶Auto Door Unlock (Crash Unlock: Automatic Door Unlock in Collision)
The air bag collision signal input cannot be accepted within 7 seconds after turning the
ignition key to "ON" position.
After this period, the door lock system outputs "UNLOCK" for all doors for 5 seconds from
40 ms after receiving the air bag collision signal.
Even though the key is turned to "OFF" position during the output of "UNLOCK", the output
continues on for remaining period.
The function is erased when turning "OFF" the ignition switch. 1.
2.
3.
4.
Cautions for door lock/unlock control
The "Unlock" control by air bag signal prevails over any "LOCK" or "UNLOCK" control by
other functions.
The "LOCK/UNLOCK" request by other functions will be ignored after/during the output of
"UNLOCK" by the air bag.
However, the door lock is controlled by other functions when the ignition switch is "OFF".
"LOCK" (or "UNLOCK") output is ignored if "LOCK" (or "UNLOCK") output is required while
performing the output of "LOCK" (or "UNLOCK").
(However, UNLOCK by air bag signal and operation by the remote control key are valid.)
If the door lock system outputs "LOCK" and "UNLOCK" simultaneously, only the "LOCK"
output can be activated. 1.
2.
3.
4.

02-44
▶Time Lag Power Window Control
The power window relay output is "ON" when turning on the ignition switch.
The power window relay output is "ON" for 30 seconds when turning off the ignition
switch.
The power window relay output is "OFF" when opening the driver's door or the
passenger's door.
The power window relay is turned "OFF" when receiving the remote control key lock signal
(armed mode) during its extended operation period of 30 seconds. 1.
2.
3.

02-46
2) Description of Theft Deterrent Function
(1) Armed mode activation requirements
The "LOCK" output is "ON" when the "LOCK" signal is received from transmitter while the
ignition key is removed and all doors are closed.
The armed mode is activated when the door lock switch is locked (hazard warning flasher
blink twice).
The armed mode is still activated and the hazard warning flasher blink twice when the
"LOCK" signal is received from the remote control key again in armed mode.
When the "LOCK" signal is received from the remote control key while any of doors is not
closed, only the "LOCK" output can be done and then activates the armed ready mode
(without theft deterrent horn and hazard warning flasher). At this moment, if the ignition key is
inserted or the door lock switch is unlocked, it cancels the armed mode and activates the
normal mode.
When the door is opened or the ignition key is not inserted into ignition switch within 30
seconds after receiving "UNLOCK" signal from the remote control key, it outputs "LOCK" and
then activates armed mode (RELOCK operation). Also, at this moment, the system blinks
hazard warning flasher twice.
The armed mode will not be activated except above conditions.
Ex) The armed mode will not be activated when the door is locked by the ignition key. a.
b.
c.
d.
e.

02-478710-01
(2) Armed mode cancellation requirements
(3) Warning operation requirements
(4) Warning operation
(5) Warning cancellation requirements
(6) Operation when warning is cancelled
Receiving UNLOCK signal from the remote control key or starting the engine. a.
When opening the door in armed mode
When unlocking the door lock switch in armed mode by other than the remote control key
When closing and then opening the door after completion of warning (27 seconds) a.
b.
c.
The theft deterrent horn and hazard warning flasher output is "ON" for 27 seconds at the interval
of 1 second. a.
Cancels warning by using any signal from the remote control key (LOCK, UNLOCK, PANIC,
ESCORT) during warning operation.
Cancels warning after 27 seconds (remaining time) while the ignition key is turned to "ON"
position.
If the ignition switch is turned to ON position when the warning is activated in armed mode,
the warning is cancelled immediately and the warning buzzer stops after 27 seconds
(remaining time). a.
b.
c.
The theft deterrent horn and hazard warning flasher outputs are "OFF". a.

02-48
(7) Operation when warning is cancelled
The theft deterrent horn and hazard warning flasher is activated when fitting the battery in armed mode.
(The same operation as when alarm condition is met in armed mode is performed.)
PANIC Warning ▶
The PANIC warning output is "ON" for 27 seconds using the horn and hazard warning
flasher, when receiving the PANIC signal from the remote control key.
The PANIC warning output is "OFF" when pressing any button on the remote control key
during PANIC warning.
The followings are about the theft deterrent warnings. 1.
2.
3.
The theft deterrent warning is deactivated when receiving PANIC signal from the
remote control key during theft deterrent warning.
The theft deterrent warning output is "ON" when the theft deterrent conditions are
established during PANIC warning (PANIC output is "OFF").
The PANIC warning output is "ON" when receiving the PANIC signal from the remote
control key in Armed Ready / Armed / Warning Completion / Relock Ready mode
(maintaining the theft deterrent mode). a.
b.
c.
This function operates only in armed mode. 4.
RemovedNormal Armed Warning Remark
Normal O
RELOCK operation:
When the door is not
opened or the ignition key
is not inserted into ignition
switch for 30 seconds after
receiving "UNLOCK" signal,
outputs "LOCK" and then
activates armed mode Armed Ready O
Armed O
Warning O
Warning Completion O O O
RELOCK Ready O
Installed

02-498710-01
Automatic Hazard Warning Lamp Switch (SHP: Safety Hazard Protection) ▶
When the automatic hazard warning lamp switch is pressed for approx. 0.1 to 0.59
seconds, the hazard warning lamp blinks 3 times at an interval of 0.35 seconds.
When the automatic hazard warning lamp switch is pressed for approx. 0.6 seconds or
longer, the hazard warning lamp blinks 10 times at an interval of 0.35 seconds.
This function is only available when the ignition key is in the "ON" position.
If the ignition key is turned to the "OFF" position during this function is activated, this
function is immediately deactivated.
If the system receives signals for the turn signal lamp operation during this function is
activated, this function is immediately deactivated.
While the turn signal lamp signals are already inputted, pressing the automatic hazard
warning lamp switch does not activate the automatic hazard warning lamp function. 1.
2.
3.
4.
5.
6.
Automatic hazard warning lamp switch ▶
Press briefly (0.1 ~ 0.59 seconds): The hazard
warning lamp blinks three times.
Press and hold (more than 0.6 seconds): The
hazard warning lamp blinks ten times. ·
·

02-52
Specification of Receiver ▶
Operating requirements 1.
You should remove the ignition key. -
Code registration requirement 2.
You can register the code only using the diagnostic device. -
Transmitter code registration 3.
You can register up to 5 transmission codes to the remote control key.
The receiver does not output the received code during registration.
Connect the device to the diagnostic terminal.
The code can be registered only by the panic signal from the transmitter.
(Other switches (LOCK/UNLOCK/ESCORT) can't code.) a.
b.
c.
Remote Door Lock ▶
All doors are locked when briefly pressing the door LOCK burron on remote control key (less
than 0.5 seconds).
The system outputs LOCK signal immediately after receiving the door lock message from the
remote control key. The system activates the theft deterrent mode when all doors are locked
while they are fully closed (the hazard warning lamps blink twice.). 1.
2.

02-56
Outside rearview mirror folding/unfolding control ▶
If you press the folding/unfoling switch with the ignition switch in "ON" position, the outside
rearview mirror is folded or unfolded depending on the previous status. At this time,
folding/unfolding outputs are maintained for about 15 to 17 seconds.
Even though the ignition switch is turned to "OFF" position during folding/unfolding output,
the output continues on for remaining time.
When removing and refitting the battery, the first switch input folds the mirror.
If you turn the ignition switch to the "OFF" from "ON" position, operating time is extended by
60 seconds. Unlikely the previous model, opening the front door does not affect the
extension time. (i.e., opening/closing the front door is irrelevant)
If the unfolding input is received from the switch during folding output or the folding input is
received during unfolding output, the existing output stops and new output is activated after
the delay time of about 0.1 second.
When the vehilce speed is above 50 km/h with the mirror unfolded, even though the folding
signal is received it is overridden.
(folding is possible only at vehicle speed of less than 50 km/h ) 1.
2.
3.
4.
5.
6.

02-578710-01
STICS Outside Rearview Mirror Folding/Unfolding Control Circuit ▶
If you remove the ignition switch and open the driver's door with the sunroof open, the chime
buzzer sounds.
As soon as you close the driver's door or the sunrooof, the chime buzzer output stops.
However, when operating conditions in step (1) are met after the operation in step (2), the
chime buzzer will not sound again. If you turn the ignition swtich to the "ON" position again
and the operating contions in step (1) are met, the chime buzzer sounds again.
If the operating condtions for door ajar warning and sunroof open warning are met at the
same time, the sunroof open warning is activated preferentially. 1.
2.
3.
4. In order to prevent the driver from getting off the vehicle with the sunroof open, the reminder
function for the driver is added. This function is activated as follows:Sunroof open warning ▶