ignition SSANGYONG NEW ACTYON SPORTS 2012 Repair Manual

02-60
You can register up to 2 transmission codes to the remote control key.
The receiver does not output the received code during registration.
The remote control key should be coded using the diagnostic device. a.
b.
c.
1) Operating requirements
You should remove the ignition key.
2) Code registration requirement
You can register the code only using the diagnostic device.
3) Transmitter code registration
5. REKES Key Coding

02-618710-01
4) How to Code REKES Key
If you replace the REKES key or immobilizer & rechargeable key to new one, you should code the
REKES key using the diagnostic device. (maximum 5)
Connect the diagnostic device to the vehilce and select the vehicle type and system (RK-
STICS). When the following screen is displayed, select 'REMOCON CODING'. 1.
Remove the remote control key from the ignition key box and press 'Next'. Press the door
UNLOCK (PANIC) button on the remote control key once (for approx. 2 seconds or longer). 2.

02-630000-00
5) How to Register Transponder
Insert the ignition key into the key cylinder and turn it to the "ON" position.
Select the vehicle type and system (immobilizer) on the diagnosis program.
Select the Transponder registration menu and enter the password. (initial value is "0000") Select
"Next". 1.
2.
3.
Press "Next" with the first key in key box. 4.

03-4
2) System Diagram
The certification for the immobilizer is performed when turning the ignition switch to the "ON" position
after the CAN communication between the ECU and immobilizer is established.

03-97010-06
Immobilizer and Warning Lamp ▶
This indicator comes on when the ignition key
is communicating with the engine control unit
(during engine starting) and goes out after
starting the engine.
When turning the ignition key to the "ON"
position, the ECU (engine control unit)
transmits the challenge message to the
immobilizer & rechargeable unit.
(This is to verify whether the key is valid. If the
verification fails, it transmits re-verification
signals 3 times for 2 seconds. If three re-
verifications fail, it stops verification and starts
re-verification after 10 seconds.) (1)
ECUOnly when the two signals are identical, it recognizes the
key as the authorized one and transmits the positive
message to the ECU. (6)
The ECU enable the engine to be started. (7)
Do not drop or shock to the transponder in the key as it may be damaged.
With a damaged transponder, the engine cannot be started.
When you erase the code or register an extra key, please attend on the site.
In any cases, the immobilizer system can not be removed from the vehicle. If you attempt to
remove it and damage the system, starting will be impossible, so never attempt to remove,
damage or modify it.
The remote engine starter cannot be installed to the vehicle equipped with the immobilizer
system. ·
·
·
·
·ON: In communication
Blinks twice at one second intervals: Immobilizer
system fault
Blinks once at 2 second intervals: Immobilizer unit
not coded
The immobilizer indicator does not come
on if the communication time between
immobilizer key and ECU is too short.
Instrument
panel

04-18
Brightness of LCD display when turning ON/OFF tail lamp ▶
Sequen
ceLevelTail lamp OFF Tail lamp ON
Display brightness Brightness
ratioDisplay brightness Brightness
ratio
1 ILL1 25% 5%
2 ILL2 40%9%
(LCD: 12%)
3 ILL3 55%13%
(LCD: 19%)
4 ILL4 70%17%
(LCD: 26%)
5 ILL5 85%21%
(LCD: 33%)
6 ILL6 100%25%
(LCD: 40%)
Illumination conditions of LCD display when turning ON/OFF tail lamp ▶
The illumination for the LCD display comes on when turning on the tail lamp and is adjustable only
when the ignition is ON. When turning on the tail lamp switch with the ignition OFF, the tail lamp
comes on but the LCD display is not illuminated. Refer to the illustration below.
IGN ON
(Comes on regardless of whether the tail lamp
switch is turned ON or OFF)Tail lamp comes on with IGN OFF
(Tail lamp comes on but the illumination for LC
D
display is not turned on)

04-20
3. WARNING LIGHTS AND INDICATORS
ESP OFF Indicator
This lamp comes on when pressing
the "ESP OFF" switch or the ESP
system is defective. When the ESP
system is activated, this lamp blinks
and a chime sounds.
Immobilizer Indicator
This indicator comes on when the
ignition key is communicating with
the engine control unit for approx.
0.5 seconds.
Glow Indicator
When the ignition key is turned ON,
this indicator lamp comes on and the
combustion chamber is warmed up.
In the vehicle equipped with direct
injection type engine, this indicator
may come on very shortly or may not
come on.
Fog Lamp / Headlamp
High Beam Indicator
This lamp comes on when
the fog lamp or high beam
headlamp operates to
indicate the operating
status.Engine Oil Pressure Warning Ligh
This lamp comes on if there is any
fault in the engine oil system and
goes off when a certain amount of
time has elapsed after turning ON
the ignition switch.
Door ajar warning
light
This light comes on
when a door or
tailgate is either
opened or not
closed completely.Brake warning light
This warning light comes on
and warning buzzer sounds
when the parking brake is
applied and/or the brake fluid
level is lower than specified
level.Seat belt warning lamp
The seat belt warning light comes on
and the seat belt warning chime
sounds for 6 seconds when the
ignition switch is turned to "ON"
position unless the driver's seat belt is
securely fastened. This reminding
operation stops when the driver
fastens the seat belt.
Engine Coolant Overheat
Warning Light
When the coolant temperature is
abnormally hot (over 120℃), this
warning light blinks and a
warning buzzer sounds at 1 Hz.
(check cooling system)

04-218210-01
ABS Warning Light
This warning light comes on
when the ignition switch is
turned to "ON" position and
should go out if the system is
normal.
The vehicle with ABS performs
self-diagnosis. During this
diagnosis, brake pedal
vibration and noise may be
apparent when the driving
motors discharges the
hydraulic pressure from the
internal hydraulic device.4WD IndicatorLow Fuel Level
Warnig Light
This warning light
comes on when the
fuel will soon be
exhausted. The time
it takes turn on,
however, varies
according to the
gradient of the
vehicle.
4WD HIGH Indicator
The lamp blinks momentarily during
the change of driving mode.
4WD LOW Indicator
The lamp blinks momentarily during
the change of driving mode.
4WD CHECK Warning Light
This indicates that there is
something wrong in the transfer
case system. (check the system) -
-
-
Auto Cruise Control
Indicator
Operating the cruise
control switch turns on
the indicator lamp to
indicate the cruise
control system is
activated.
Water Separator Warning Light
This lamp comes on to warn the driver of
water in the fuel tank which causes the
loss of engine power. When a certain
amount of water is accumulated, the lamp
comes on and a chime sounds.
Engine CHECK Warning Light
This warning light comes on when
the ignition switch is turned to "ON"
position and should go out if the
system related to engine control is
normal.
This comes on when different
sensors and devices related to
engine control are defective.
Winter Mode
Indicator
Pressing the "W" side of the
automatic transmission mode
selector switch switches the
driving mode to winter mode and
turns on the indicator lamp.
Use this mode to drive off
smoothly on icy and slippery
roads.
Charge Warning Light
This warning light comes on when the
ignition switch is turned on and go off
when the engine is started.
If this light doesn't go off after engine
starting, it means there is a malfunction in
the system.
Engine Hood Open Warning Light
When the engine hood is open, this light
comes on to inform the driver.

04-22
How to enter self-diagnosis mode ▶
Turn the ignition ON with the TRIP switch pressed.
Press and hold the TRIP switch for 5 to 10 sec. with the ignition ON.
Press and hold the TRIP switch for less than 10 sec. and then cycle the switch between ON
and OFF 5 times within 3 sec.
Confirm that the self-diagnosis mode is activated through the instrument cluster. 1.
2.
3.
4.
4. SELF-DIAGNOSIS CHECK
Self-diagnosis OFF ▶
If the engine speed increases to 396 rpm or more while the engine is cranking or the ignition key
is turned OFF in self-diagnosis mode, the self-diagnosis mode is turned OFF automatically.
Operating process ▶
Speed gauge: changes from 0 to 220 km
RPM gauge: changes from 0 to 6,000 rpm
Fuel gauge: changes from E to F
Temperature gauge: changes from C to H
Warning/Indicator lamps: All indicator/warning lamps controlled by MICOM are turned ON.
Dimming: Illuminates at the highest lighting level.
LCD display: All elements are activated. 1.
2.
3.
4.
5.
6.
7.

07-37810-01
1. OVERVIEW
The wiper and washer system are controlled by STICS according to driver's wiper switch
operation. And the detection of rain drops by rain sensor is transmitted to STICS as the signal for
wiper system control.
(saem as KYRON)
The characteristics of the wiper and washer system including basic functions of manual wiper are
as follows.
1) Wiper Function Coupled Auto Washer
Pressing the AUTO washer switch with the
ignition key OFF and INT AUTO switch OFF
sprays the washer fluid for 2 sec. and
operates the wiper 4 times and then
immediately sprays the washer fluid for 1.5
sec. and operates the wiper 3 times.
2) Integrated Auto Light Sensor in Rain Sensor Unit
The rain sensor unit is installed on the best
location to detect the rain drops and the
lighting intensity. And an auto light sensor is
newly integrated into the rain sensor unit for
more precise measurements. To control the
system, the sensed values of rain sensor and
auto light sensor are sent to pin no. 63 in
STICS unit. Auto
washer
operation
switch
(press)
Auto light
sensor
photodiode Rain sensor
emitter lens