relay SSANGYONG NEW ACTYON SPORTS 2013 Owner's Manual

02-38710-01
1. PERFORMANCE AND SPECIFICATIONS
1) Rated Load & Input Signals
Rated Load
▶
NO.
Item Rated Load
1 Chime bell / Buzzer DC 12V 350 mA (Inductive load)
2 Front room lamp DC 12V 16W (Lamp load)
3 Rear room lamp DC 12V 8W (Lamp load)
4 Ignition key illumination DC 12V 1.2W (Lamp load)
5 Seat belt indicator DC 12V 1.2W (Lamp load)
6 Parking brake warning lamp DC 12V 1.2W (Lamp load)
7 Door ajar warning lamp DC 12V 1.2W (Lamp load)
8 Door lock relay DC 12V 200 mA (Inductive load)
9 Door unlock relay DC 12V 200 mA (Inductive load)
10 Horn relay DC 12V 260 mA
11 Tail lamp relay DC 12V 200 mA (Inductive load)
12 Hazard warning lamp relay DC 12V 200 mA (Inductive load)
13 Power window relay DC 12V 200 mA (Inductive load)
14 Rear defogger relay DC 12V 200 mA (Inductive load)
15 Wiper LOW relay DC 12V 200 mA (Inductive load)
16 Wiper HIGH relay DC 12V 200 mA (Inductive load)
17 Front washer motor DC 12V 1.5A
18 Head lamp relay DC 12V 750 mA (Inductive load)
19 Front defogger relay DC 12V 200 mA (Inductive load)
20 Mirror lock relay DC 12V 200 mA (Inductive load)
21 Mirror unlock relay DC 12V 200 mA (Inductive load)

02-6
1. GENERAL
STICS of KORANDO SPORTS, called as RKSTICS (REKES + STICS (Super Time \
& Integrated
Control System)), is almost the same as that of ACTYON SPORTS in terms\
of its function and role.
Chime
STICS unit
PAS buzzerICM relay box
Inside of Lower IP Cover on Driver Side

02-8
2) Operation Logic
▶Wiper MIST and Front Washer Coupled Wiper
The wiper relay is turned on at 0.3 seconds after from the time when the washer switch is turned
on for 0.1 to 0.59 seconds with the ignition switch "ON".If the wiper parking terminal gets off, the
wiper relay is turned off.
-
The wiper relay is turned on at 0.3 seconds after from the time when the\
washer switch is turned
on for more than 0.6 seconds with the ignition switch "ON". The wiper re\
lay gets on 3 times
immediately after turning off the washer switch.
-

02-10
▶Auto Washer and Wiper Switch (AFW)When the auto washer switch is turned on with the ignition switch "ON" and the INT switch
"OFF", the washer motor output gets ON for 1 second. If the system recog\
nizes the output signal,
the wiper relay output gets ON during 4 cycles and the washer motor output gets ON for 1
second. Then, the wiper relay output gets OFF after 3 cycles.
-

02-138710-01
Rain sensing unit
(AUTO light integrated type)
▶INT Switch Auto Position Remi nder (Power-Up Reminder Wiper)
When turning off and on the auto INT switch, the system drives the wiper motor through LOW
relay regardless of communication with rain sensor.
When turning the INT-AUTO switch from the "OFF" to "ON" position with the ignition switch in the
"ON" mode, the LOW relay operates to drive the wiper motor for 1 cycle, regar\
dless of the rain
sensor communication.
After that, when turning the INT-AUTO switch fr om the "OFF" to "ON" position, the LOW relay
operates to drive the wiper motor for 1 cycle only if data from the rain\
sensor indicates rain drops.
-
-
Multifunction wiper switch:
AUTO and sensitivity control
A sensor that emits infrared rays through LED and
then detects the amount of rain drops by receiving
reflected rays against sensing section (rain senso
r
mounting section on the windshield) with
photodiode (auto light sensor integrated type) AUTO
: Wiper operates automatically by rain sensor
FAST↔SLOW : Auto delay/Auto speed control. A
position that can control sensitivity against rains on
the windshield and transmits wiping demand signal
accordingly

02-158710-01
▶Sensitivity ControlThe wiper LOW relay is turned on and the wiper motor runs one cycle when the volume sensitivity
is increased (ex: sensitivity 0 ⇒ 1) while the ignition switch and the INT switch is in the "ON"
position, and the wiper motor is in "Parked" position). However, the wiper motor can be operated
only when the rain sensor detects the "Rain Detected" signal.
If the volume sensitivity is changed more than 2 stages within 2 seconds, the wiper motor runs
only one cycle.
-
※

02-178710-01
▶Defective Rain SensorThe wiper relay (LOW) is turned on and the wiper motor runs one cycle when the volume
sensitivity is changed to 2 from 3 during receiving the malfunction sign\
al from the rain sensor,
while the ignition key is in "ON" position and the wiper switch is in "O\
N" position.
-
The wiper relay (LOW) is turned on and the wiper motor runs one cycle when the volume
sensitivity is changed to 3 from 4 during receiving the malfunction sign\
al from the rain sensor,
while the ignition key is in "ON" position and the wiper switch is in "O\
N" position.
-

02-18
Check whether the multifunction wiper switch is in the "AUTO" position.
Check the power to the sensor. Check the conditions of the pin 3 (Groun\
d) and the pin 4
(IGN).
Check the wiper relay for defective.
1)
2)
3)
Symptom 2. It rains but the system does not work in "AUTO" position.
TROUBLE SHOOTING
▶
The wiper does not operate one cy cle when turning the multifunction
wiper switch to the "AUTO" from the "OFF" position or starting the
engine while the wiper switch is in the "AUTO" position.
When starting the engine with the multifunction wiper switch in the "AUTO" position, the
wiper operates one cycle to remind a driver that the wiper switch is in \
the "AUTO" position.
When the multifunction wiper switch is turned to "AUTO" from "OFF", the wiper operates
one cycle.
It always operates one cycle for the initial operation, however, the wiper does not operate
afterwards to prevent the wiper blade wear if not raining when turning the wiper sw\
itch to
"AUTO" from "OFF". However, the wiper operates up to 5 minutes after rain stops\
. If this
function does not occur, check No. 8 pin. If the pin is normal, check the wiper relay related
terminals.
1)
2)
Symptom 3. The wiper operates 3 or 4 times at high speed abruptly.
Check whether the variable resistance knob on the multifunction wiper switch i\
s set in
"FAST". The "FAST" is the highest stage of sensitivity and very sensitive to small amount o
f
rain drops. Therefore, change the knob to low sensitivity.
Symptom 4. The wiper operates continuoulsy even on the dry windshield glass.
Check the wiper blade for wear. If the wiper blade cannot wipe the glass uniformly and
clearly, this problem could be occurred. In this case, replace the wiper\
blade with new one.
Check whether the variable resistance knob on the multifunction wiper switch is set in
"FAST" The "FAST" is the highest stage of sensitivity and very sensitive\
to small amount o
f
rain drops. Therefore, change the knob to low sensitivity.
1)
2)
Symptom 1.

02-22
Cautions for wiper control1. Speed sensitive INT (intermittent) wiper
The wiper relay continues to output for remaining "ON" time even when the INT switch is
turned off during its operation.
IGN switch "ON", INT switch "OFF": Resume the intermittent time when tur\
ning "ON"
IGN switch "OFF", INT switch "ON": Resume the intermittent time when tur\
ning "ON"
1)
2)
3)
2. Controls when the wiper motor parking is defective The wiper relay continues to output when the parking terminal is fixed at the ground or IGN
while the wiper relay is "ON" (INT switch = ON or washer switch = ON)
(The output stops immediately after turning off the switch)
-
[Pause time of vehicle speed sensitive INT wiper]
Pause time against vehicle speed

02-238710-01
▶Ignition Key Reminder WarningThe chime buzzer sounds continuously when opening the driver's door whil\
e the ignition key is in
ignition switch.
When removing the ignition key or closing the driver's door during chime\
buzzer operation, the
buzzer stops.
This function does not work when the IGN1 switch is in "ON" position.
-
-
-
(The function has priority over the "TAILLAMP ON WARNING".)
Chime Buzzer
PAS buzzer
ICM relay box
STICS