SSANGYONG NEW ACTYON SPORTS 2013 Service Manual

03-8
Front seat warmer switch
1. OVERVIEW
The seat consists of the front seats (driver and front passenger) and rear seats.
The heated wires are inserted into the seat cushion and seatback for front seat and is inserted into the
seat cushion for rear seat.
While the front and rear LH/RH seats have 3-point seat belt, rear center seat has 2-point seat belt.
2. SEAT/SEAT BELT LAYOUT
Driver side
Passenger side
Front seat and seat switchFront seat belt (3-point)

03-97410-01
Rear seat warmer switch
Rear seat
Rear seat
warmer switch
3-point seat belt
2-point seat belt Seat belt buckle
Rear seat belts (3-point and 2-point)

03-10
3. HOW TO ADJUST AND OPERATE SEAT
1) Front Seat
There are two types of front seats: the power seat which uses the electric motor to adjust the seat
movement, seatback and seat cushion and
the manual seat which adjusts them by pulling the lever by hand.
For both power seat and manual seat, the driver can adjust the headrest and driver lumbar support by
hand.
The heated wires are inserted into the seatback and the seat cushion, which are operated by the front
seat warmer switch located to the center fascia.
To adjust headrest ▶
To adjust headrest height
To adjust the height of the headrest, raise or
lower it while pressing the headrest sleeve (A).
To adjust headrest tilting
Pull the headrest forwards and release to adjust
its tilting angle in 3 steps.

03-117410-01
Power Seat
To adjust seat slide
Moving the slide knob forward and rearward
activates the slide motor to move the seat forward
and rearward.
To adjust seatback ▶
Manual seat
To adjust seat slide
To move the seat forward or backward, pull and
hold the seat slide lever up and move the seat as
desired. Then, release the lever.
To adjust seat back angle
When moving the upper part of the recline knob
forward/backward, the seatback angle is adjusted
as the recline motor rotates the rail.To adjust seat back angle
To change the seatback angle, lean forward
slightly and raise the lever. Then, lean back to the
desired angle and release the lever. After
adjusting, make sure the lever is returned to its
original position and the seatback is locked.

03-12
Power Seat
To adjust seat cushion angle
When moving the slide switch forward/backward,
the front and rear up/down motors rotate the rails
to move the front and rear side of the cushion
up/down.Manual seat
To adjust seat cushion angle and
height
You can adjust the angle and height of the front o
r
rear section of the seat cushion by rotating the
adjustment knob on the side of the seat clockwise
or counterclockwise.
To adjust seat cushion height
When moving the slide switch up/down,
the front rear up/down motor rotates the rail to
move the whole seat cushion up/down.To adjust driver seat lumbar support
When you raise and lower the lumbar support
lever on the power and manual seats, the lumbar
support goes in and out of the seat.

03-137410-01
Seat belt reminder
2) Seat Belt Reminder & Pretensioner
In addition to securing the occupants to the seat, the seat belt has the seat belt reminder and the
pretensioner which retracts the seat belts while the air bags are deployed and the load limiter which
protects the seat belt from being retracted excessively.
Driver's seat belt reminder ▶
The STICS detects if the seat belt is fastened or not using a signal from the driver's seat belt switch. The
seat belt reminder flashes and the chime sounds when the seat belt is not fastened.
The seat belt reminder stops its operation as soon as the seat belt is fastened.
Chime
Pretensioner ▶
It is installed on the driver and passenger LH/RH B-pillar and the pretensioner is installed in it, which
retracts the seat belt when the air bag is deployed in case of the front impact to secure the occupant to
the seat.
Anchor
Pretensioner

04-37340-00
1. SPECIFICATIONS
2. CAUTIONS WHEN WORKING
Wear clean work clothes and gloves.
Replace and wash the gloves frequently.
Any unauthorized modification or operational test is not allowed since the sunroof motor and control
unit are preset at the factory.
Take care not to drop the sunroof assembly when removing it and do not keep it right up. 1.
2.
3.
4.
Operating voltage 9 ~ 16 V
Operating current (open & close) Max. 6 A
At no load Max. 2 A
Leakage current Max. 1 mA or less
Roof motor operating speed (at opening and closing)1.2 ± 0.5 sec./100 mm
Motor overload stop conditionsCurrent for up to 26 A and torque (load)
for up to 8.3 Nm
Opening amount230 ± 3
Vertical/horizontal tolerance for sunroof glass panel± 2 mm/± 2.5 mm
3. CAUTIONS FOR OPERATION
Even though the sunroof can be operated when the engine is not running, operating the sunroof
repeatedly with the engine turned off will run down the battery. Operate the sunroof while the engine is
running.
When the sunroof operation is completed, release the switch. Keeping pressing the switch can result
in malfunction.
Especially in winter, never operate the sunroof if operation areas are iced. Wait until melted.
Make sure that the sunroof is completely closed when leaving the vehicle. Leaving the vehicle with the
sunroof open result in a theft. In addition, rain or snow can get into the vehicle through the open
sunroof.
When the sunroof is fully open, wind buffeting symptom can be worse. In this case, try to adjust the
sunroof position manually or open the sunroof until the wind buffeting is disappeared
Parts of the body can be trapped in the sunroof and can be struck by passing objects. Do not stick
hands, head or anything else out of the openings.
Remove any dirt and foreign material stuck on the edge of the sunroof glass periodically.
Noise can occur due to friction when operating the sunroof. -
-
-
-
-
-

04-4
TILTOPEN
Sunroof switch
1. SYSTEM LAYOUT
Sunroof assemblySunroof motor &
control unit

04-57340-00
2. OPERATING PROCESS
1) Sunroof Switch
This can be closed or open manually to block sunlight when the sunroof function is not in use. The sunroof glass can be open automatically and can be tilted by the switch operation. The sunroof switches are included in the overhead console switches and consists of the TILT,
CLOSE and OPEN switches.
CLOSE
OPEN ▷
▷
Sun shade blindSunroof glass Sunroof operation switch ▶
Closes the sunroof.
Opens the sunroof.
Sunroof glass ▶
Roller blind ▶