ignition SSANGYONG RODIUS 2012 Workshop Manual

02-358710-01
▶Auto Door Unlock (Crash Unlock)
The air bag collision signal input cannot be accepted within 7 seconds after turning the ignition
key to "ON" position.
After this period, the door lock system outputs "UNLOCK" for all doors for 5 seconds from 40
ms after receiving the air bag collision signal.
Even though the key is turned to "OFF" position during the output of "UNLOCK", the output
continues on for remaining period.
The function is erased when turning "OFF" the ignition switch. 1.
2.
3.
4.
The "Unlock" control by air bag signal prevails over any "LOCK" or "UNLOCK" control by
other functions.
The "LOCK/UNLOCK" request by other functions will be ignored after/during the output of
"UNLOCK" by the air bag. However, the door lock is controlled by other functions when the
ignition switch is "OFF".
"LOCK" (or "UNLOCK") output is ignored if "LOCK" (or "UNLOCK") output is required while
performing the output of "LOCK" (or "UNLOCK"). (However, UNLOCK by air bag signal and
operation by the remote control key are valid.)
If the door lock system outputs "LOCK" and "UNLOCK" simultaneously, only the "LOCK"
output can be activated. 1.
2.
3.
4.

02-36
12) Time Lag Power Window Control
<007b008f008c004700970096009e008c00990047009e00900095008b0096009e00470090009a0047009b009c00990095008c008b00470096008d008d0047009e008f008c00950047009b009c0099009500900095008e0047009b008f008c00470090008e00
950090009b00900096009500470092008c00a00047009b0096> “ON” position.
<007b008f008c004700970096009e008c00990047009e00900095008b0096009e00470099008c0093008800a000470090009a0047009b009c00990095008c008b004702c80076007502c90047008d009600990047006000570047009a008c008a0096009500
8b009a0047004f007b005800500047009e008f008c00950047>turning the ignition key to
“OFF” position.
However, the power window relay stays on for 90 seconds (T2) when the ignition key is turned
to “OFF” position while the door is opened.
The
p<0096009e008c00990047009e00900095008b0096009e00470099008c0093008800a000470090009a0047009b009c00990095008c008b004702c80076007502c900470088008e0088009000950047008d009600990047006000570047009a008c008a009600
95008b009a0047004f007b0059005000470091009c009a009b> for once when opening
the door during its extended operation period of 90 seconds (T1).
<007b008f008c004700970096009e008c00990047009e00900095008b0096009e00470099008c0093008800a000470090009a0047009b009c00990095008c008b004702c80076006d006d02c90047009e008f008c00950047008a00930096009a0090009500
8e0047009b008f008c0047008b0096009600990047008b009c>ring its extended operation
period of 90 seconds (T2). 1.
2.
3.
4.

02-378710-01
13) Theft Deterrent
(1) Description of Burglar Alarm Function
The “LOCK” output is “ON” when receiving the “LOCK” signal from transmitter while the ignition
key is removed and all doors are closed. The armed mode is activated when the door lock
switch is locked (theft deterrent horn output: once, hazard relay output: twice).
<007b008f008c0047009b008f008c008d009b0047008b008c009b008c00990099008c0095009b0047008f009600990095004700880095008b0047008f008800a100880099008b00470099008c0093008800a000470096009c009b0097009c009b009a004700
880099008c004702c80076007502c90047009e008f008c0095> receiving the “LOCK” signal
from the remote control key again in armed mode (theft deterrent horn output: once, hazard
relay output: twice).
<007e008f008c009500470099008c008a008c0090009d00900095008e004702c800730076006a007202c90047009a0090008e0095008800930047008d0099009600940047009b008f008c00470099008c00940096009b008c0047008a00960095009b009900
96009300470092008c00a00047009e008f00900093008c0047>any of doors is not closed,
<00960095009300a00047009b008f008c004702c800730076006a007202c900470096009c009b0097009c009b0047008a0088009500470089008c0047008b00960095008c004700880095008b0047009b008f008c009500470088008a009b0090009d008800
9b008c009a0047009b008f008c0047008800990094008c008b> ready mode (without theft
deterrent horn and hazard warning flasher). At this moment, if the ignition key is in the ignition
<009a009e0090009b008a008f00530047009b008f008c0047008b0096009600990047009c009500930096008a00920047009a009e0090009b008a008f00470090009a0047009b009c00990095008c008b004702c80076007502c90047009600990047009b00
8f008c0047008b009600960099004700930096008a00920047>switch is unlocked (after 0.6
seconds), cancels the armed mode and activates the normal mode. However, in these cases, if
closing the door and locking the door lock switch, the theft deterrent horn outputs once and the
hazard warning flasher outputs twice and then activates armed mode.
When the door is not opened or the ignition key is not inserted into ignition switch for 30
seconds after receiving “UNLOCK” signal, outputs “LOCK” and then activates armed mode
(RELOCK operation). Also, at this moment, the system outputs the theft deterrent horn and
hazard warning flasher.
The armed mode will not be activated except above conditions.
Ex) The armed mode will not be activated when the door is locked by the ignition key. 1.
2.
3.
4.
5.
▶Theft deterrent mode ON conditions

02-40
(3) Auto Light Function
The lights automatically come on and off according to the ambient brightness when the
multifunction light switch is in “AUTO” position while the ignition key is in “ON” position. 1.
(4) Auto Door Lock
The doors are locked and the theft deterrent mode is activated again if any of doors is not
opened after unlocking them with a REKES key.
Sends the message in 5 seconds after locking the doors automatically. 1.
2.

03-4
2) System Diagram
The certification for the immobilizer is performed when turning the ignition switch to the "ON"
position after the CAN communication between the ECU and immobilizer is established.

03-57010-06
2. OVERVIEW
The Immobilizer System provides an additional theft deterrent to the vehicle in which it is installed
and prevents it from being started by unauthorized persons. The transponder integrated in the key
and the engine control unit have the same code. When the ignition key with the integrated
transponder is turned to the ON position, the ECU (Engine Control Unit) checks the crypto code
of the key and, if correct, allows the vehicle to start the engine. If the verification has been failed,
the engine cannot be started and the immobilizer warning lamp blinks.
Immobilizer unit

03-77010-06
ECU
Immobilizer Indicator and Warning Lamp ▶
This indicator comes on when the ignition
key is communicating with the engine
control unit (during engine starting) and
goes out after starting the engine.
When turning the ignition key to ON
position, the ECU transmits the challenge
message to the immobilizer unit to verify
whether the key is valid. (1)
Only when the two signals are identical, it
recognizes the key as the authorized one and
transmits the positive message to the ECU.
The ECU allows the engine to be started. (6)
(7)
Do not drop or shock to the transponder in the key as it may be damaged.
With a damaged transponder, the engine cannot be started.
When you erase the code or register an extra key, let the owner attend on the site.
In any case, the immobilizer system cannot be removed from the vehicle. If you attempt to
remove it and damage the system, starting will be impossible, so never attempt to remove,
damage or modify it.
The remote engine starter cannot be installed on the vehicle equipped with the immobilizer
system. -
-
-
-
-Lamp ON: in communication
Blinking twice for one second: immobilize
r
system failure
Blinking once for two seconds: immobiliz
e
unit is not coded
The immobilizer indicator does not
come on if the communication time
between immobilizer key and ECU is
too short.
Immobilizer Indicator and Warning Lamp

07-4
2. CAUTIONS ON RAIN SENSOR
When the wiper switch is in the AUTO position, the wiper will operate for 1 cycle if the initial
engine start is made. This may cause the wiper blades to wear prematurely. Therefore, other
than rainy days, set the switch to the OFF position. Especially during the winter time, check if
the wiper blades are not frozen to the windshield.
Operating the wiper with the blades frozen can damage the wiper motor.
If you operate the wipers when the windshield is dry without spraying washer fluid, the
windshield can be scratched and the wiper blades can wear prematurely. Use the wiper with the
washer fluid when the windshield is dry.
When it does not rain, turn the wiper switch to the OFF position.
Turn the wiper switch to the OFF position before any car wash to avoid unwanted operation of
the wipers. -
-
-
-
When cleaning the windshield over the sensor with damp clothes, the wiper may operate
suddenly. It could cause serious injury. Make sure to place the wiper switch to the OFF
position and ignition switch OFF when not in use.
Irregular operation (abrupt operation) ▶
Check if the sensor is off the position.
Check if the rain sensor cover is securely installed.
Check if the customer is familiar to how to control the wiper sensitivity.
Check if the wiper sensitivity control is set to the FAST side (step 5).
Check the wiper blade for wear.
If the wiper blade cannot wipe the glass uniformly and clearly, it may cause the rain sensor to
work irregularly. Therefore, in this case, replace the wiper blade with a new one. -
-
-
-

08-78610-11
▶ Rain sensing operation point
The wiper relay is turned on and the wiper motor runs one cycle when the ignition key is
<009b009c00990095008c008b0047009b0096004702c80076007502c9004700970096009a0090009b0090009600950047004f009e008f00900093008c0047009b008f008c0047009e00900097008c00990047009a009e0090009b008a008f00470090009a00
4700900095004702c80068007c007b007602c9004700970096>sition).
The wiper relay (LO) is turned on and the wiper motor runs one cycle when changing the
<009e00900097008c00990047009a009e0090009b008a008f0047009b0096004702c80068007c007b007602c9004700970096009a0090009b0090009600950047008d00990096009400470088009500a000470096009b008f008c0099004700970096009a00
90009b009000960095009a0047004f009e008f00900093008c> the ignition key is in “ON”
<00970096009a0090009b009000960095005000550047007e008f008c00950047009b008f008c0047009e00900097008c00990047009a009e0090009b008a008f00470090009a0047009b009c00990095008c008b0047009b0096004702c80068007c007b00
7602c9004700970096009a0090009b00900096009500470088>gain from other positions, the
system drives the wiper relay (LO) to run the wiper motor one cycle only when the rain sensor
detects the “Rain Detected” signal. 1)
2)

08-98610-11
The wiper system continuously outputs the parking signal of current sensitivity when the
parking terminal is grounded (while the ignition key is in “ON” position and the wiper switch is
in “AUTO” position). 1)
<0b540047007b008f008c0047009e00900097008c0099004700940096009b0096009900470099009c0095009a004700960095009300a00047009e008f008c00950047009b008f008c004700990088009000950047009a008c0095009a009600990047009900
8c0098009c00900099008c009a0055>
When the parking terminal is fixed to IGN (HIGH), the wiper system outputs the operating
signal of current sensitivity for 2 seconds, then continuously outputs the parking signal of
current sensitivity. 2)
<0b540047007b008f008c0047009e00900097008c0099004700940096009b0096009900470099009c0095009a004700960095009300a00047009e008f008c00950047009b008f008c004700990088009000950047009a008c0095009a009600990047009900
8c0098009c00900099008c009a0055>
▶ Wiper operation when the wiper parking terminal is grounded