ignition SSANGYONG RODIUS 2012 Owner's Manual

10-10
4) Recovery of Set Speed (RESUME)
Even if the cruise control is cancelled, the previous set cruise speed can be recovered by pulling
up the cruise control lever when the current vehicle speed is over 36 km/h without an acceleration
intervention. But if you turn off the ignition switch, the memorized set speed is cleared and you
cannot recover the previous set speed.
But the driver should know the previous set speed to react to the changed vehicle speed
properly. If the vehicle speed increases abruptly, depress the brake pedal to adjust the vehicle
speed properly.

10-12
Do not move the shift lever to Neutral position while driving with the cruise control turned on.
Otherwise, it may result in system malfunction or accidents.
Always be prepared to use the brake or accelerator pedal for safe driving while the cruise
control system is running.
The actual speed can be different from the set speed momentarily when driving on a uphill
or downhill. So, it is recommended to disable the cruise control function on a uphill or
downhill. hen driving on a steep hill use the engine brake and foot brake properly to protect
the vehicle system and for a safe driving.
Ensure that the safe distance is maintained and use the brake pedal if needed. 1.
2.
3.
4.
(1) Abnormal Cancellation of the Cruise Control
When the rapid deceleration is applied without braking.
When the rapid acceleration is applied without acceleration pedal intervention.
When the cruise control lever is faulty.
When the brake switch and the brake light switch input signal are implausible. 1.
2.
3.
When the cruise control function is cancelled abnormally or intermittent problems occur, stop the
vehicle and turn off the ignition switch and remove the key to reset the system. After a while, turn
on the ignition switch again to operate the cruise control system.

01-38410-02
1. CAUTIONS WHEN WORKING ON ELECTRICAL UNITS
80℃
10A 15A
Disconnect the negative cable from the
battery in advance when working on
electrical units. -
Make sure to turn "OFF" the ignition switch
and other lamp switches before
disconnecting or connecting the negative
battery cable. (Otherwise, semiconductor
parts can be damaged.)
Do not drop or appy excessive impact to
sensors and relays. -
If a fuse is blown, replace it with a fuse
which has the correct amperage rating. If
you use a fuse with higher capacity than
the specification, the component can be
damaged or catch fire. -

02-6
2. FUNCTIONS OF RK STICS
1) Wiper Control
(1) Wiper MIST and Washer Coupled Wiper
The wiper relay is turned on 0.3 seconds (T1) after turning “ON” the washer switch for 0.2 ~
0.59 seconds (T2) with the ignition key “ON”, and it is turned off when the parking terminal is
turned off. 1.
The wiper relay is turned on 0.3 seconds (T1) after turning “ON” the washer switch over 0.6
seconds (T2) with the ignition key “ON”, and it is turned on three times immediately after
turning off the washer switch. 2.

02-98710-01
▶ Rain sensing operation point
The wiper relay is turned on and the wiper motor runs one cycle when the ignition key is
<009b009c00990095008c008b0047009b0096004702c80076007502c9004700970096009a0090009b0090009600950047004f009e008f00900093008c0047009b008f008c0047009e00900097008c00990047009a009e0090009b008a008f00470090009a00
4700900095004702c80068007c007b007602c9004700970096>sition).
The wiper relay (LO) is turned on and the wiper motor runs one cycle when changing the
<009e00900097008c00990047009a009e0090009b008a008f0047009b0096004702c80068007c007b007602c9004700970096009a0090009b0090009600950047008d00990096009400470088009500a000470096009b008f008c0099004700970096009a00
90009b009000960095009a0047004f009e008f00900093008c> the ignition key is in “ON”
<00970096009a0090009b009000960095005000550047007e008f008c00950047009b008f008c0047009e00900097008c00990047009a009e0090009b008a008f00470090009a0047009b009c00990095008c008b0047009b0096004702c80068007c007b00
7602c9004700970096009a0090009b00900096009500470088>gain from other positions, the
system drives the wiper relay (LO) to run the wiper motor one cycle only when the rain sensor
detects the “Rain Detected” signal. 1)
2)

02-118710-01
The wiper system continuously outputs the parking signal of current sensitivity when the
parking terminal is grounded (while the ignition key is in “ON” position and the wiper switch is
in “AUTO” position). 1)
<0b540047007b008f008c0047009e00900097008c0099004700940096009b0096009900470099009c0095009a004700960095009300a00047009e008f008c00950047009b008f008c004700990088009000950047009a008c0095009a009600990047009900
8c0098009c00900099008c009a0055>
When the parking terminal is fixed to IGN (HIGH), the wiper system outputs the operating
signal of current sensitivity for 2 seconds, then continuously outputs the parking signal of
current sensitivity. 2)
<0b540047007b008f008c0047009e00900097008c0099004700940096009b0096009900470099009c0095009a004700960095009300a00047009e008f008c00950047009b008f008c004700990088009000950047009a008c0095009a009600990047009900
8c0098009c00900099008c009a0055>
▶ Wiper operation when the wiper parking terminal is grounded

02-138710-01
The wiper relay (LO) is turned on and the wiper motor runs one cycle when the wiper
sensitivity is changed to 3 from 4 during receiving the malfunction signal (2) from the rain
sensor (while the ignition key is in “ON” position and the wiper switch is in “AUTO” position). 2)
The wiper relay (LO) is turned on and the wiper motor runs one cycle when the wiper sensitivity
is changed to 2 from 1 during receiving the malfunction signal (3) from the rain sensor (while
<009b008f008c00470090008e00950090009b00900096009500470092008c00a000470090009a004700900095004702c80076007502c9004700970096009a0090009b009000960095004700880095008b0047009b008f008c0047009e00900097008c009900
47009a009e0090009b008a008f00470090009a004700900095> “AUTO” position). Also, the wiper
relay (LO) is turned on and the wiper motor runs one cycle when the wiper sensitivity is
changed to 2 from 1 during receiving the ground fixed or IGN fixed signal from the rain sensor. 3)

02-16
▶INT Switch Auto Position Reminder (Power-Up Reminder Wiper)
When turning off and on the auto INT switch, the system drives the wiper motor through
LOW relay regardless of communication with rain sensor.
When turning the INT-AUTO switch from the "OFF" to "ON" position with the ignition
switch in the "ON" mode, the LOW relay operates to drive the wiper motor for 1 cycle,
regardless of the rain sensor communication.
After that, when turning the INT-AUTO switch from the "OFF" to "ON" position, the LOW
relay operates to drive the wiper motor for 1 cycle only if data from the rain sensor
indicates rain drops. 1.
2.

02-178710-01
2) Ignition Key Reminder
▶Key Reminder Warning
<007b008f008c0047008a008f00900094008c00470089009c00a100a1008c009900470096009c009b0097009c009b0047009000950047009b008f008c00470070006a0074004700890096009f0047008a00960095009b00900095009c008c009a0047009e00
8f008c0095004700960097008c009500900095008e0047009b>he driver’s door while the
ignition key is inserted into ignition switch.
<007e008f008c009500470099008c00940096009d00900095008e0047009b008f008c00470090008e00950090009b00900096009500470092008c00a00047009600990047008a00930096009a00900095008e0047009b008f008c0047008b00990090009d00
8c009902c5009a0047008b0096009600990047008b009c0099>ing chime buzzer output, the
output turns off.
This function is not available when the ignition switch is “ON”. 1.
2.
3.

02-18
This function does not work if the vehicle speed is over 3 km/h.
<007b008f008c0047009a00a0009a009b008c009400470096009c009b0097009c009b009a004702c8007c007500730076006a007202c90047008d009600990047005c0047009a008c008a00960095008b009a0047004f007b005900500047008d0099009600
94004700570055005c0047009a008c008a00960095008b009a> after the driver’s door is
<00960097008c0095008c008b004700880095008b0047009b008f008c0047008b009600960099004700930096008a00920047009a009e0090009b008a008f00470090009a0047008a008f00880095008e008c008b0047009b0096004702c800730076006a00
7202c90047004f009e008f00900093008c0047009b008f008c> ignition key is in ignition
switch).
<007b008f008c0047009a00a0009a009b008c009400470096009c009b0097009c009b009a004702c8007c007500730076006a007202c90047008d009600990047005c0047009a008c008a00960095008b009a0047004f007b005900500047009e008f008c00
950047009b008f008c0047008b009600960099004700930096>ck switch is changed to
“LOCK” from “UNLOCK” and the driver’s door is closed within 0.5 seconds (T1) (while the
ignition key is in ignition switch). 1.
2.
3. ▶Key Reminder
Operating conditions for (*1) and (*2) -
<004f00510058005000610047006b00990090009d008c009902c5009a0047008b00960096009900470090009a004700960097008c0095008c008b004700880095008b0047008b00990090009d008c009902c5009a0047008b00960096009900470093009600
8a00920047009a009e0090009b008a008f00470090009a0047>turned to LOCK
<004f0051005900500061004700770088009a009a008c0095008e008c009902c5009a0047008b00960096009900470090009a004700960097008c0095008c008b004700880095008b004700970088009a009a008c0095008e008c009902c5009a0047008b00
9600960099004700930096008a00920047009a009e0090009b>ch is turned to LOCK