weight SSANGYONG RODIUS 2012 Service Manual

02-22
Rear view
5. CYLINDER HEAD COVER AND OIL SEPARATOR
The cylinder head cover is made by high strength plastic to reduce the weight. The multi twist type
oil separator improves the oil consumption.
Components ▶
1) Cylinder Head Cover
Cylinder head cover
Cylinder head cover

02-290000-00
1) Chain Drive
(1) Overview
The drive chain is single chain drive system with simple design and variable performance, and it
utilizes the hydraulic tensioner to reduce the wave impact generated by the chain. This chain is light
weight and has high durability through single bush chain. Shoulder bolts are used for better NHV.
7. CHAIN AND GEAR DRIVE SYSTEM
D20DTR engine uses single stage chain drive system. Timing chain drives the exhaust side and
gear drive the intake side. Timing chain is single bush type. Upper chain drives HP pump
connected to intake Camshaft by driving exhaust cam shift sprocke, and lower chain drives oil
pump to lubricate the engine.

04-31719-00
1. SPECIFICATIONS
Shorten the service interval under severe conditions such as driving on a dusty road or off-
road. *
Unit Description Specification
Air cleaner elementFilter type Dry, filter element
Initial resistance Max. 300 mmAq
Service interval EU: Change every 20,000 km
GEN: Change every 15,000 km
Air cleaner assemblyWeight 2.36kg
Operating temperature-30 ~ 100℃
IntercoolerRadiation over 13,000 Kcal
Pressure loss at turbocharger below 90 mmHg
Cooling type Air cooled type
Core size 450W*130H*70T
Core type C/FIN

06-31914-01
1. SPECIFICATION
Unit Description Specification
TurbochargerMax. expansion coefficient 4.0
Max. turbine speed 226,000rpm
Max. temperature of turbine
housing790 ℃
Weight 6.5kg
E-VGT actuator Operation duty cycle 250Hz

08-31520-00
1. SPECIFICATION
Description Specification
Cooling system Type Water cooling, forced circulation
Coolant Capacity approx. 11.5 L
RadiatorCore size589W x 538H x 27T (over 3,170 cm²)
Flow type Cross flow
AntifreezeType Long life coolant
Mixing ratio
(water:antifreeze)50 : 50
Cooling fan
moduleMotor type DC motor
Motor weight 2.14 kg
Control type PWM type
Fan runout 3 mm
Coolant reservoirCapacity over 1.5 L
Circulation Closed roof type
Pressure cap Screw type
Pressure 1.4bar
ThermostatType Wax pallet type
Opening temperature90 ℃
Fully open temperature
100℃
Valve lift 8mm

11-31461-01
1. SPECIFICATION
Description Specification
Capacity 12V 2.3kW
Engagement Meshed type
Rotating direction Clockwise
Pinion gear manufacturing Cooled forging
Solenoid operating voltage Max. 8 V
Weight 2.5 kg
Bracket manufacturing Aluminum die casting

09-38790-01
1. SPECIFICATIONS
1) Parking Aid Unit
Detecting type :
Detecting distance : Ultrasonic wave
Description Specification
Rated voltage DC 12V
Operating voltage DC 9V ~ 16V
Current consumption Unit below 100 mA
Sensor below 20 mA (for each sensor)
Sensor insulating resistanceover 5 MΩ
Operating temperature-30˚C ~ +80˚C
Storage temperature-40˚C ~ +85˚C
Relative humidity 95% RH max
Weight Unit160g ± 10g max
Sensor70g ± 10g max
25 ~ 120 cm (distance
between sensor and
obstacle)

05-33240-01
Weight 32.4 kg (including oil)
Oil capacity 1.4L
Oil type ATF DEXRON II or III
Location Transfer case
Major element Housing Part-time
Bolt 11EA, M8 x 1.25
Input shaft A/T: outer spline
Description Specifications
Total length 343mm
1. SPECIFICATIONS

07-74411-01
Coil Spring ▶
Description 4WD 2WD
Spring rate (kg/mm)10.01 ± 5% 10.01 ± 5%
Coil diameter (mm)16.7 16.7
Inner diameter
(mm)D 158.3 58.3
D 288.3 88.3
Spring identificationNone + Red or Blue Yellow + Red or Blue
Number of windings8.49 8.49
Number of active windings6.99
CVW (Curved
Vehicle Weight)Height (mm)256.0 256.0
Weight (kg)976.9 ± 4% 834.9 ± 4%
Stress (kg/mm)69.53 59.42
Winding directionClockwise Clockwise

07-10
(2) Coil Spring
High tensile steel used.
Minimum length should be 20 mm longer than the fully compressed length.
Spring seat used. -
-
-
Description 4WD 2WD
Part number45110-21000 45110-21000
Spring rate (kg/mm)12.0 ±5% 12.0 ±5%
Coil diameter (mm)15.9 15.9
Inner diameter (mm)69.1 69.1
Pitch (mm)85.0 85.0
Number of windings9.55 9.55
Number of active windings8.35 8.35
CVW (Curved Vehicl
e
Weight)Height (mm)250 250
Weight (kg)880 880
Stress (kg/mm)
62.1 62.1
Winding directionClockwise Clockwise
Spring length (mm)323.3 323.3
Dimension ▶