SSANGYONG TURISMO 2013 Service Manual

08-14
Parking Brake Adjustment ▶
Adjust the brake adjuster using a flat-bladed screwdriver so that the parking brake shoe is tight on the
inner face of the brake disk when installing it, then unscrew the adjuster by 4 ~ 5 notch. (Clearance
between the inner face of brake disk and brake shoe should be about 0.2 mm) 1.
Turn in direction of (A) to decrease the clearance
Turn in direction of (B) to increase the clearance -
-
1
Adjust the parking brake shoe, depress the
parking brake pedal 5 times and release it. 2.
Adjust the equalizer assembly bolt under
the vehicle so that the equalizer assembly
stops at the first notch when the parking
brake pedal is depressed with a force of 19
to 22 kgf. 3.
Turn in the direction of (A) to tension the
parking brake cable
Turn in the direction of (B) to loosen the
parking brake cable -
-

08-154850-03
1. COMPONENTS

08-16

08-174850-03
1) Front Brake
The front brake system uses the ventilated disc and double piston caliper.
Caliper carrier
Pad spring
Brake pad
Bolt-caliper
Brake disc
CaliperPiston
Brake hose
Caliper assemblyBrake discBrake pad

08-18
2) Rear Brake
▶ Brake Disc
Brake disc
Lock nutCaliper
Brake hose
Backing plate
Adjusting bolt
Brake shoe Lock nut
Parking brake
operating lever

08-194850-03
▶Caliper Assembly
Bolt-caliper
CaliperPiston
Pad springCaliper carrierBrake pad
Caliper assembly
Brake pad

08-20
4) Parking Brake
▶Parking Brake Controls
Operating lever
Return spring - lowerShoe holding
springReturn spring - upper
Adjusting bolt
Pedal assembly
Equalizer assembly

08-214850-03
Parking brake switch Release lever
Brake damper
Pedal assembly
Pedal
Rear brake cable - LH
Rear brake cable - RH Tension spring
Equalizer boltEqualizer assembly Release cable

09-34891-01
1. SPECIFICATIONS
1) Pressure Sensor
UnitDescription
Location
ABS ESP
HECU
(Hydraulic &
Electronic Control
Unit) CPU:MCU60 (32bit)
Clock Frequency:
28 MHz
Memory: 128~256 KB CPU:MCU60 (32bit)
Clock Frequency:
28 MHz
Memory:256~512 KB Under the front washer
reservoir
Wheel Speed
SensorActive type wheel speed
sensorActive type wheel speed
sensorOn each wheel
Front air gap:
0.3 ~ 1.3mm,
Rear air gap:
0.3 ~ 1.3 mm
Steering Wheel
Angle SensorN/AMaximum angular speed:
1500°/sec
Operating voltage:
9~16 VUnder the steering
wheel
Sensor ClusterN/AIntegrated with yaw rate
sensor and lateral sensorUnder the audio
assembly
Pressure Sensor
N/A Analog outputUnder the master
cylinder
Description Specification
Supplying voltage approx. 5 V (4.75~5.25 V)
Max. pressure 350 bar

09-4
2) Sensor Cluster
3) Steering Wheel Angle Sensor
Air gap between sensor and rotorFront 0.3 ~ 1.3 mm
Rear 0.3 ~ 1.3 mm
Current (at 2.75 km/h)IHIGH : 14 mA
ILOW : 7 mA
Voltage (when turning the steering wheel one turn per second) 7.5 ~ 20 V
4) Active Wheel Speed Sensor
Operating voltage 9~16 V
Maximum output current 10 mA
Max. current consumption100 ma
Maximum detection angle speed 1500˚/s
Operating temperature -30~75℃
Supplying voltage 9 to 16 V (battery voltage)
Description Specification
Description Specification
Description Specification
Supplying voltage approx. 5 V (4.75~5.25 V)
Output voltage while in stationary approx. 2.5 V (Ignition ON)
Output range 0.2~4.8 V
Operating start speed4˚/s