light SUBARU FORESTER 1999 Service Manual PDF

2) Turn the headlights on. Perform the aiming
adjustment for the other headlight as follows:
CAUTION:
Do not perform lateral headlight aiming adjust-
ment.
H6M0709A
WH L h
1,060 mm
(41.73 in)710 mm
(27.95 in)712 mm
(28.03 in)11 4 m m
(4.49 in)
B: REMOVAL AND INSTALLATION
1. HEADLIGHT AND SIDE MARKER LIGHT
1) Disconnect ground cable from battery.
2) Remove front grille and
disconnect connector from headlight.
3) Remove screw (A) then remove side marker
light while disconnecting connector.
4) Remove extension (B)
5) Remove bolts (C) which secure headlight and
remove headlight.
S6M0044A
6) Install in the reverse order of removal.
Tightening torque:
6.4
±0.5 N´m (0.65±0.05 kg-m, 4.7±0.4 ft-lb)
NOTE:
When installing, securely fit clip (on fender side)
into locating (on front turn signal light side).
2. REAR COMBINATION LIGHT
1) Disconnect ground cable from battery.
2) Remove rear quarter upper and lower trim.
3) Remove nuts and disconnect connector.
S6M0045
4) Attach adhesive cloth tape to body area around
rear combination light.
5) Using a standard screwdriver, carefully pry rear
combination light off and away from the front of the
vehicle.
6) Install in the reverse order of removal.
Tightening torque:
6.4
±0.5 N´m (0.65±0.05 kg-m, 4.7±0.4 ft-lb)
CAUTION:
IDo not pry on the rear combination light
forcefully as this may scratch the vehicle body.
IRemove all traces of adhesive tape from
body before installation.
IAttach butyl rubber tape to back of rear com-
bination light before installing rear combina-
tion light on body for sealing purposes.
3. REAR FINISHER LIGHT
1) Disconnect ground cable from battery.
2) Remove rear gate trim access hole cover.
3) Remove the four nuts.
S6M0427
4) Detach rear finisher light while disconnecting
connector.
6
6-2[W4B1]SERVICE PROCEDURE
4. Lighting

5) Install in the reverse order of removal.
4. HIGH-MOUNTED STOP LIGHT
1) Disconnect ground cable from battery.
2) Remove cap (A) by prying on the edge with a
screwdriver.
3) Remove screws (B) and then detach cover (C).
4) Remove screws (D) and then detach high-
mounted stop light while disconnecting connector.
B6M1343B
5) Install in the reverse order of removal.
5. COMBINATION SWITCH
1) Disconnect ground cable from battery.
2) Remove instrument panel lower cover. 5-4 [W1A0].>
3) Remove screws which secure upper column
cover to lower column cover.
S6M0042
4) Disconnect connector from combination switch.
5) Remove screws which secure switch and
remove switch.
S6M0046
6) Install in the reverse order of removal.
C: INSPECTION
1. COMBINATION SWITCH (LIGHTING)
Move combination switch to respective positions
and check continuity between terminals.
H6M0500B
B6M1458A
7
[W4C1]6-2SERVICE PROCEDURE
4. Lighting

2. HEADLIGHT RELAY
Check continuity between terminals when terminal
No. 4 is connected to battery and terminal No. 3 is
grounded.
When current
flowsBetween terminals
No. 1 and No. 2Continuity exists.
When current
does not flowBetween terminals
No. 1 and No. 2Continuity does not
exist.
Between terminals
No. 3 and No. 4Continuity exists.
S6M0048B
3. TAIL AND ILLUMINATION RELAY
Check continuity between terminals (indicated in
table below) when terminal No. 4 is connected to
battery and terminal No. 3 is grounded.
When current
flowsBetween terminals
No. 1 and No. 2Continuity exists.
When current
does not flowBetween terminals
No. 1 and No. 2Continuity does not
exist.
Between terminals
No. 3 and No. 4Continuity exists.
S6M0048B
5. Front Wiper and Washer
A: ADJUSTMENT
1) Turn the wiper switch to OFF position.
2) Adjust so that the blades meet the ceramic print
point mark (A).
S6M0049B
3) Adjust washer ejecting area on windshield
glass as shown in the figure when vehicle stops.
Ejecting area:
A: 350 mm (13.78 in)
B: 100 mm (3.94 in)
C: 60 mm (2.36 in)
B6M1315A
8
6-2[W4C2]SERVICE PROCEDURE
5. Front Wiper and Washer

2. HEADLIGHT RELAY
Check continuity between terminals when terminal
No. 4 is connected to battery and terminal No. 3 is
grounded.
When current
flowsBetween terminals
No. 1 and No. 2Continuity exists.
When current
does not flowBetween terminals
No. 1 and No. 2Continuity does not
exist.
Between terminals
No. 3 and No. 4Continuity exists.
S6M0048B
3. TAIL AND ILLUMINATION RELAY
Check continuity between terminals (indicated in
table below) when terminal No. 4 is connected to
battery and terminal No. 3 is grounded.
When current
flowsBetween terminals
No. 1 and No. 2Continuity exists.
When current
does not flowBetween terminals
No. 1 and No. 2Continuity does not
exist.
Between terminals
No. 3 and No. 4Continuity exists.
S6M0048B
5. Front Wiper and Washer
A: ADJUSTMENT
1) Turn the wiper switch to OFF position.
2) Adjust so that the blades meet the ceramic print
point mark (A).
S6M0049B
3) Adjust washer ejecting area on windshield
glass as shown in the figure when vehicle stops.
Ejecting area:
A: 350 mm (13.78 in)
B: 100 mm (3.94 in)
C: 60 mm (2.36 in)
B6M1315A
8
6-2[W4C2]SERVICE PROCEDURE
5. Front Wiper and Washer

2) Remove front pillar lower trim.
S6M0097
3) Disconnect connector from cruise control mod-
ule.
4) Remove bolt, then remove cruise control mod-
ule.
S6M0098
5) Install in the reverse order of removal.
5. STOP AND BRAKE SWITCH
1) Disconnect ground cable from battery.
2) Disconnect connector from switch, then remove
the switch.
3) Install in the reverse order of removal.
6. CLUTCH SWITCH
1) Disconnect ground cable from battery.
2) Disconnect connector from switch, then remove
the switch.
3) Install in the reverse order of removal.
13. Front Fog Light
A: REMOVAL AND INSTALLATION
1) Disconnect ground cable from battery.
2) Remove the two screws, then draw out the front
fog light from front bumper.
S6M0085
3) Disconnect the connector.
4) Install in the reverse order of removal.
22
6-2[W12B5]SERVICE PROCEDURE
13. Front Fog Light