meter SUBARU FORESTER 2004 Service User Guide
[x] Cancel search | Manufacturer: SUBARU, Model Year: 2004, Model line: FORESTER, Model: SUBARU FORESTER 2004Pages: 2870, PDF Size: 38.67 MB
Page 135 of 2870
AB-3
AIRBAG SYSTEM (DIAGNOSTIC)
Check List for Interview
2. Check List for Interview
A: CHECK
Customer’s Name Inspector’s Name
Date Vehicle Brought In / / Registration No.
Odometer Readingkm
milesVIN
Date Problem Occurred / / Registration Year / /
Weather❏ Fine ❏ Cloudy ❏ Rainy ❏ Snowy ❏ Other:
Temperature°C (°F)
Road Condition❏ Level road❏ Uphill ❏ Downhill❏ Rough road ❏ Others:
Vehicle Operation❏ Starting❏ Idling
❏ Driving (❏ Constant speed❏ Acceleration❏ Deceleration
❏ Steering wheel turn❏ Others: )
Details of Problem
Check Airbag Warning Light❏ Normal (After turning the ignition switch to ON, lit for 7 seconds and goes off.)
❏ Remains ON❏ Remains OFF
Check DTC❏ Normal Code❏ DTC: (Code: )
Page 153 of 2870
AB-21
AIRBAG SYSTEM (DIAGNOSTIC)
Airbag Control Module I/O Signal
5. Airbag Control Module I/O Signal
A: WIRING DIAGRAM
1. LHD MODEL
B31(BLACK)(GREEN)
(GREEN) (YELLOW)
(YELLOW)B82
WI-03204
7
6
2
3
8
GWGRGY
GY
R
GRGB
GRL
W
GYRGRLW
19
BB28
1
R
2354
653192
AIRBAG
CIRCUIT AIRBAG
WARNING LED
IG
IGNITION RELAY
(IG) FB-33
F/B FUSE No. 14
(IG)FB-20
F/B FUSE No. 11
(IG)FB-21
F/B FUSE No. 6
(IG)
L
GR
GW
W
B
GRGR5GR
GB
B9
C8
BB10
1
2
L
W
REF. TO GND(L)-04
CHECK
CONNECTOR
DIAGNOSIS
CONNECTOR
DIAGNOSIS
TERMINAL
B31
AB1
AIRBAG CONTROL MODULE
AB3
B81
B82
B79B38i3
B37i2
TO POWER SUPPLY ROUTING
(GRAY)
B79
1234567891011121314
B
B
12
3456
B37
AB3
COMBINATION
METER B: C:
i11i10
i11
i10 B: C:
A/B(L)-01
A/B(L)-01
12345678910
123456789101112131415161718192021222324252627282930
34 128910 11
12 13 14 15 16 17 18 19 20 21 22 23 24567
1234567891011121314151617
1819202122232425262728
1
34562
B38
219
32
1234 5610 11 12 13 14 15716
23 3019 20
22 26 27 28 29817
24 3118
25
REF. TO GND(L)-02
BB
Page 156 of 2870
AB-24
AIRBAG SYSTEM (DIAGNOSTIC)
Airbag Control Module I/O Signal
2. RHD MODEL
A/B(R)-01A/B(R)-01
WI-03206
7
6
2
3
8
GWGY
GY
R
GRGR
RGRL
W
YWLgRBR
10
BB20
65143
6
B
BW
2
2753192
IG
IGNITION RELAY
(IG)FB-36
F/B FUSE No. 14
(IG)FB-20
F/B FUSE No. 11
(IG)FB-21
F/B FUSE No. 6
(IG)
L
GR
GW
W
B
GYGY16GY
GR
B
B9
C8
B10
1
2
L
W
BL
BL
REF. TO GND(R)-04
REF. TO E/G(RNA)-05REF. TO E/G(RTB20)-05REF. TO E/G(RTB25)-05
CHECK
CONNECTOR
DIAGNOSIS
CONNECTOR
DIAGNOSIS
TERMINAL
B31
AB1
(GRAY)
B79
AIRBAG CONTROL MODULE
AB3
B81
B82
B79
B38i3
TO POWER SUPPLY ROUTING
1234567891011121314
GY
(BLACK)B82
B
REF. TO GND(R)-05
B
i3
B31(GREEN) i11 C:
B:
(GREEN)
i10
AIRBAG
CIRCUIT AIRBAG WARNING
LED LIGHT
COMBINATION
METER B: C:
i11i10
12
34561
3456212345678910
123456789101112131415161718192021222324252627282930
(YELLOW)
AB3
1234567891011121314151617
1819202122232425262728
(YELLOW)
219
32
1234
5610 11 12 13 14 15716
23 3019 20
22 26 27 28 29817
24 3118
25
Page 167 of 2870
AB-35
AIRBAG SYSTEM (DIAGNOSTIC)
Airbag Warning Light Failure
1. LHD MODEL
WIRING DIAGRAM:
Step Check Yes No
1 CHECK POOR CONTACT IN CONNECTORS
(AB1) AND (B31).
1) Turn the ignition switch to OFF, disconnect
the battery ground cable, and wait more than
20 seconds.
2) Remove the side sill cover. (Driver’s side)
3) Confirm that firm contact is secured
between connectors (AB1) and (B31).Is the poor contact in connec-
tors (AB1) and (B31)?Repair the body
harness or replace
the airbag main
harness with body
harness.Go to step 2.
AB-00739
12
34561
2345678910123456789101112131415161718192021222324252627282930
B31 i11AB3
i10
B:
C: i10
i11
AIRBAG
WARNING
LIGHTCOMBINATION
METERB9
B8
B10
NO.14
i3B38 28
i2B37 19
5
AIRBAG CONTROL MODULEAB3
B31
AB1
3
3
AIRBAG
CIRCUIT
E
BATTERY
1234567891011121314151617
1819202122232425262728
IGNITION
SWITCH
B: C:
Page 168 of 2870
AB-36
AIRBAG SYSTEM (DIAGNOSTIC)
Airbag Warning Light Failure
2 CHECK AIRBAG WARNING LIGHT.
1) Turn the ignition switch to OFF, disconnect
the battery ground cable, and wait more than
20 seconds.
2) Connect the connector (1T) in test harness
T to body harness connector (B31).
3) Connect the connector (1M) in test harness
M to connector (2T) in test harness T.
4) Connect the battery ground cable and turn
the ignition switch to ON.
5) Connect the connectors, (3M) and (4M) in
test harness M.Is the airbag warning light
turned off?Go to step 4.Go to step 3.
3 CHECK BODY HARNESS.
Check the body harness.
N
OTE:
After problem has been eliminated, disconnect
the connectors (3M) and (4M).Is the anything unusual to body
harness? Repair the body
harness.Replace the com-
bination meter
printed circuit.
Meter Assembly.>
4 CHECK POOR CONTACT.
Confirm that firm contact is secured between
the airbag control module and the connector
(AB3).
tor (AB3)?Replace the airbag
main harness with
body harness or
replace the airbag
control module.
Module.>Go to step 5.
5 CHECK AIRBAG MAIN HARNESS.
1) Turn the ignition switch to OFF, disconnect
the battery ground cable, and wait more than
20 seconds.
2) Connect the connector (AB1) to (B31).
3) Disconnect the connectors (AB2) and
(AB30).
4) Remove the glove box and disconnect the
connectors (AB4).
5) Disconnect the connector (AB3) from the
airbag control module, and connect the con-
nector (1R) in test harness R.
6) Connect the battery ground cable and turn
the ignition switch to ON.
7) Connect the connectors (5R) and (6R) in
test harness R.
N
OTE:
After problem has been eliminated, disconnect
the connectors (5R) and (6R).Is the airbag warning light
turned off?Go to step 6.Replace the airbag
main harness with
body harness.
6 CHECK GROUNDING CIRCUIT.
1) Turn the ignition switch to OFF, disconnect
the battery ground cable, and wait more than
20 seconds.
2) Disconnect the connector (AB3) from the
airbag control module.
3) Connect the connector (1R) in test harness
R to body harness connector (AB3).
4) Measure the resistance between connector
(2R) in test harness R and the chassis ground.
Connector & terminal
(2R) No. 10 — Chassis ground:
(2R) No. 11 — Chassis ground: Is the resistance less than 10
Ω?Replace the airbag
control module.
Module.>Repair the body-
grounding circuit. Step Check Yes No
Page 169 of 2870
AB-37
AIRBAG SYSTEM (DIAGNOSTIC)
Airbag Warning Light Failure
2. RHD MODEL
WIRING DIAGRAM:
Step Check Yes No
1 CHECK POOR CONTACT IN CONNECTORS
(AB1) AND (B31).
1) Turn the ignition switch to OFF, disconnect
the battery ground cable, and wait more than
20 seconds.
2) Remove the side sill cover. (Driver’s side)
3) Confirm that firm contact is secured
between connectors (AB1) and (B31).Is the poor contact in connec-
tors (AB1) and (B31)?Repair the body
harness or replace
the airbag main
harness with body
harness.Go to step 2.
AB-00740
12
34561
2345678910123456789101112131415161718192021222324252627282930
B31 i11AB3
i10
B:
C: i10
i11
AIRBAG
WARNING
LIGHTCOMBINATION
METERB9
B8
B10
NO.14
i3B38 20
10
16
AIRBAG CONTROL MODULEAB3
B31
AB1
1
3
AIRBAG
CIRCUIT
E
BATTERY
1234567891011121314151617
1819202122232425262728
IGNITION
SWITCH
Page 170 of 2870
AB-38
AIRBAG SYSTEM (DIAGNOSTIC)
Airbag Warning Light Failure
2 CHECK AIRBAG WARNING LIGHT.
1) Turn the ignition switch to OFF, disconnect
the battery ground cable, and wait more than
20 seconds.
2) Connect the connector (1M) in test harness
M to body harness connector (B31).
3) Connect the battery ground cable and turn
the ignition switch to ON.
4) Connect the connectors, (3M) and (4M) in
test harness M.Is the airbag warning light
turned off?Go to step 4.Go to step 3.
3 CHECK BODY HARNESS.
Check the body harness.
N
OTE:
After problem has been eliminated, disconnect
the connectors (3M) and (4M).Is the anything unusual to body
harness?Repair the body
harness.Replace the com-
bination meter
printed circuit.
Meter Assembly.>
4 CHECK POOR CONTACT.
Confirm that firm contact is secured between
the airbag control module and the connector
(AB3).
tor (AB3)? Replace the airbag
main harness with
body harness or
replace the airbag
control module.
Module.>Go to step 5.
5 CHECK AIRBAG MAIN HARNESS.
1) Turn the ignition switch to OFF, disconnect
the battery ground cable, and wait more than
20 seconds.
2) Connect the connector (AB1) to (B31).
3) Disconnect the connectors (AB21) and
(AB26).
4) Remove the glove box and disconnect the
connectors (AB4).
5) Disconnect the connector (AB3) from the
airbag control module, and connect the con-
nector (1R) in test harness R.
6) Connect the battery ground cable and turn
the ignition switch to ON.
7) Connect the connectors (5R) and (6R) in
test harness R.
N
OTE:
After problem has been eliminated, disconnect
the connectors (5R) and (6R).Is the airbag warning light
turned off? Go to step 6.Replace the airbag
main harness with
body harness.
6 CHECK GROUNDING CIRCUIT.
1) Turn the ignition switch to OFF, disconnect
the battery ground cable, and wait more than
20 seconds.
2) Disconnect the connector (AB3) from the
airbag control module.
3) Connect the connector (1R) in test harness
R to body harness connector (AB3).
4) Measure the resistance between connector
(2R) in test harness R and the chassis ground.
Connector & terminal
(2R) No. 10 — Chassis ground:
(2R) No. 11 — Chassis ground: Is the resistance less than 10
Ω?Replace the airbag
control module.
Module.>Repair the body-
grounding circuit. Step Check Yes No
Page 171 of 2870
AB-39
AIRBAG SYSTEM (DIAGNOSTIC)
Airbag Warning Light Failure
B: AIRBAG WARNING LIGHT REMAINS OFF.
DIAGNOSIS:
Fuse No. 14 (in fuse box) is blown.
Body harness circuit is open.
Airbag warning light is faulty.
Airbag main harness is faulty.
Airbag control module is faulty.
CAUTION:
Before diagnosing the airbag system, be sure to turn the ignition switch to OFF, disconnect the
ground cable from battery, and wait more than 20 seconds before starting to work.
After replacing the airbag module, seat belt pretensioner, roll connector, control module or sensor,
reconnect each part and confirm that the airbag warning light operates properly.
When inspecting the airbag main harness, disconnect the airbag module connector of the driver
and passenger seats for safety reasons.
1. LHD MODEL
WIRING DIAGRAM:
AB-00739
12
34561
2345678910123456789101112131415161718192021222324252627282930
B31 i11AB3
i10
B:
C: i10
i11
AIRBAG
WARNING
LIGHTCOMBINATION
METERB9
B8
B10
NO.14
i3B38 28
i2B37 19
5
AIRBAG CONTROL MODULEAB3
B31
AB1
3
3
AIRBAG
CIRCUIT
E
BATTERY
1234567891011121314151617
1819202122232425262728
IGNITION
SWITCH
B: C:
Page 172 of 2870
AB-40
AIRBAG SYSTEM (DIAGNOSTIC)
Airbag Warning Light Failure
Step Check Yes No
1 CHECK COMBINATION METER.
Turn the ignition switch to ON, and confirm that
warning lights equipped in the combination
meter are turned on.Do the warning lights not for
airbag turn on?Go to step 2.Repair the combi-
nation meter
power supply.
Meter System.>
2 CHECK FUSE NO. 14 (IN FUSE&RELAY
BOX).
Remove the fuse No. 14 and perform visual
inspection.Is the fuse No. 14 (in fuse &
relay box) blown out? Replace the fuse
No. 14. If fuse No.
14 blows again, go
to step 3. Go to step 3.
3 CHECK AIRBAG WARNING LIGHT CIRCUIT
(IN COMBINATION METER).
1) Turn the ignition switch to OFF, disconnect
the battery ground cable, and wait more than
20 seconds.
2) Disconnect the connector (AB1) from
(B31).
3) Connect the battery ground cable and turn
the ignition switch to ON.Is the airbag warning light
turned on?Go to step 4.Replace the airbag
warning light bulb
or combination
meter printed cir-
cuit.
Meter Assembly.>
4 CHECK AIRBAG MAIN HARNESS.
1) Turn the ignition switch to OFF, disconnect
the battery ground cable, and wait more than
20 seconds.
2) Connect the connector (AB1) to (B31).
3) Disconnect the connector (AB3) from the
airbag control module.
4) Connect the battery ground cable and turn
the ignition switch to ON.Is the airbag warning light
turned on?Replace the airbag
control module.
Module.>Replace the airbag
main harness with
body harness.
Page 173 of 2870
AB-41
AIRBAG SYSTEM (DIAGNOSTIC)
Airbag Warning Light Failure
2. RHD MODEL
WIRING DIAGRAM:
AB-00740
12
34561
2345678910123456789101112131415161718192021222324252627282930
B31 i11AB3
i10
B:
C: i10
i11
AIRBAG
WARNING
LIGHTCOMBINATION
METERB9
B8
B10
NO.14
i3B38 20
10
16
AIRBAG CONTROL MODULEAB3
B31
AB1
1
3
AIRBAG
CIRCUIT
E
BATTERY
1234567891011121314151617
1819202122232425262728
IGNITION
SWITCH