light SUBARU IMPREZA 2002 2.G Owners Manual

Maintenance and service
11-36
CAUTION
If you continue to drive despite the scraping noise from the audible brake pad wear indica-
tor, it will result in the need for costly brake rotor repair or replacement.
Breaking-in of new brake pads and linings
When replacing the brake pad or lining, use only
genuine SUBARU parts. After replacement, the new
parts must be broken in as follows:
Brake pad and lining
While maintaining a speed of 30 to 40 mph (50 to 65
km/h), step on the brake pedal lightly. Repeat this
five or more times.
Parking brake lining
1. Drive the vehicle at a speed of about 22 mph (35km/h).
2. With the parking brake release button pushed in,
pull the parking brake lever SLOWLY and GENTLY.
(Pulling with a force of approximately 33 lb [147 N,15 kg].)
3. Drive the vehicle for about 220 yards (200 me- ters) in this condition. 4. Wait 5 to 10 minutes for the parking brake to cool
down. Repeat this procedure.
5. Check the parking brake stroke. If the parking
brake stroke is out of the specified range, adjust it
by turning the adjusting nut located on the parking
brake lever.
Parking brake stroke: 7 – 8 notches / 44 lb (196 N, 20 kg)
WARNING
A safe location and situation should be se- lected for break-in driving.
CAUTION
Pulling the parking brake lever too forcefully
may cause the rear wheels to lock. To avoid
this, be certain to pull the lever up slowly and
gently.

Maintenance and service
11-41
– CONTINUED –
increase in temperature could cause tread
separation, and destruction of the tires. Theresulting loss of vehicle control could lead toan accident.
Wheel balance
Each wheel was correctly balanced when your ve-
hicle was new, but the wheels will become unbal-
anced as the tires become worn during use. Wheel
imbalance causes the steering wheel to vibrate
slightly at certain vehicle speeds and detracts from the vehicle ’s straight-line stability. It can also cause
steering and suspension systems problems and ab-
normal tire wear. If you suspect that the wheels are
not correctly balanced, have them checked and ad-
justed by your SUBARU dealer. Also have them ad-
justed after tire repairs and after tire rotation. NOTE Loss of correct wheel alignment* causes the tires to wear on one side and reduces the ve-
hicle’ s running stability. Contact your SUBARU
dealer if you notice abnormal tire wear.
* : The suspension system is designed to hold each wheel
at a certain alignment (relative to the other wheels and to
the road) for optimum straight-line stability and cornering performance.
Wear indicators
Each tire incorporates a tread wear indicator, which
becomes visible when the depth of the tread
grooves decreases to 0.063 in. (1.6 mm). A tire must
be replaced when the tread wear indicator appears
as a solid band across the tread.
OM-H0231
A) New tread
B) Worn tread
1) Tread wear indicator

Maintenance and service
11-50
Battery
WARNING
Before beginning work on or near any bat-
tery, be sure to extinguish all cigarettes,
matches, and lighters. Never expose a batteryto an open flame or electric sparks. Batteriesgive off a gas which is highly flammable andexplosive. For safety, in case an explosion does occur,
wear eye protection or shield your eyes when
working near any battery. Never lean over a
battery. Do not let battery fluid contact eyes, skin,
fabrics, or paint because battery fluid is a cor- rosive acid. If battery fluid gets on your skin or in your eyes, immediately flush the area
with water thoroughly. Seek medical help im-
mediately if acid has entered the eyes.If battery fluid is accidentally swallowed,
immediately drink a large amount of milk or
water, and seek medical attention immediately. To lessen the risk of sparks, remove rings,
metal watchbands, and other metal jewelry.
Never allow metal tools to contact the positive because a short circuit will result.
Keep everyone including children away
from the battery. Charge the battery in a well-ventilated area.
Battery posts, terminals and related acces-
sories contain lead and lead compounds,
chemicals known to the State of California to
cause cancer and reproductive harm.
Wash
hands after handling.
CAUTION
Never use more than 10 amperes when charg- ing the battery because it will shorten batterylife.

Maintenance and service
11-52
HB8003CA
The other one is housed in the engine compartment.
HS0208
1) Fuse puller 2) Spare fuse
The fuse puller and spare fuses are stored in the main fuse box cover in the engine compartment.
If any lights, accessories or other electrical controls
do not operate, inspect the corresponding fuse. If a
fuse has blown, replace it.
HS0204
A) Good B) Blown
1. Turn the ignition switch to the “LOCK” position
and turn off all electrical accessories.
2. Remove the cover.
3. Determine which fuse may be blown. The backside of each fuse box cover and the “Fuse and cir-
cuits” section in chapter 12 in this manual show the
circuit for each fuse.

Maintenance and service
11-54
Installation of accessories
Always consult your SUBARU dealer before instal- ling fog lights or any other electrical equipment inyour vehicle. Such accessories may cause the elec-
tronic system to malfunction if they are incorrectly
installed or if they are not suited for the vehicle.

Maintenance and service
11-56
Wattage Bulb No.
1) Front turn signal 12V –21W —
2) Spot light 12V –8W —
3) Room light 12V –8W —
4) Side marker light (Front) 12V–5W 168
5) Parking light 12V –5W 168
6) Front fog light 12V –55W —
7) Headlight 12V–60/55W 9007 (HB3)
8) Trunk room light 12V –16W W16W
9) High mount stop light Sedan (in compartment) 12V-18W 921
Sedan (in rear spoiler) 12V-1.2W —
Wagon 12V-13W 912
10) Backup light 12V –21W 7440
11) Rear turn signal 12V –21W —
(Amber)
12) Brake light 12V –21W 7440
13) Licence plate light 12V –5W 168
14) Tail light 12V –21/5W 7443
15) Brake/tail light 12V –21/5W 7443
16 )Cargo area light 12V –13W —
17) Side marker light (Rear) 12V –5W 168
Headlight
CAUTION
Halogen headlight bulbs become very hot while in use. If you touch the bulb surfacewith bare hands or greasy gloves, fingerprints or grease on the bulb surface developinto hot spots, causing the bulb to break. If there are finger prints or grease on the bulb
surface, wipe them away with a soft cloth
moistened with alcohol.
NOTE If headlight aiming is required, consult your
SUBARU dealer for proper adjustment of the headlight aim.

Maintenance and service
11-57
– CONTINUED –
HGB021BB
1) Push 2) Pull
1. Disconnect the electrical connector while press-
ing the lock release tab.
HGB022BA
2. Remove the bulb holder from the headlight as-
sembly by turning it counterclockwise.
HGB023BA
3. Remove the bulb from the headlight assembly.
4. Install the new bulb.
5. Install the bulb holder in the headlight assembly
by turning it clockwise until it locks.
6. Reconnect the electrical connector.

Maintenance and service
11-58
Front turn signal light and parking light
HGB007CB
1) Front turn signal light
2) Parking light
Front turn signal light bulbs
HGB009BA
1. Remove the bulb socket from the headlight as-
sembly by turning it counterclockwise.
2. Pull the bulb out of the socket. Install a new bulb.
3. Set the bulb socket into the headlight assembly
and turn it clockwise until it locks.
Parking light bulbs
The headlight assembly must be removed before
the parking light bulbs can be replaced. When the
headlight assembly has been removed and then re-
installed, it may become necessary to make a head-
light aiming adjustment. It may be difficult to replace
the bulbs. Have your SUBARU dealer replace the
bulbs if necessary.

Maintenance and service
11-59
– CONTINUED –
1. Remove the front grille. Use a screwdriver to de-
tach the four clips at the top and the two hooks on
each side.
HGB027BA
: Clip : Hook
HGB028BA
2. Loosen three clips to remove the headlight side
cover.
HGB029BA

Maintenance and service
11-60
3. Remove three bolts and disconnect connectors,
and then detach headlight assembly.
HGB030BA
HGB031BA4. Remove the bulb socket from the headlight as-
sembly by turning it counterclockwise.
HGB010BA
5. Pull the bulb out of the socket. Install a new bulb.
6. Set the bulb socket into the headlight assembly
and turn it clockwise until it locks.