light SUBARU IMPREZA 2002 2.G Owners Manual

Maintenance and service
11-61
– CONTINUED –
Front fog light (if equipped)
CAUTION
Halogen fog light bulbs become very hot while
in use. If you touch the bulb surface with barehands or greasy gloves, finger prints orgrease on the bulb surface develop into hotspots, causing the bulb to break. If there are finger prints or grease on the bulb surface,
wipe them away with soft cloth moistenedwith alcohol.
HGB016BA
1. Remove the front fog light assembly by removing
the three bolts. 2. Disconnect the connector.
HGA002BA
3. Remove the front fog light case cap by turning it
counterclockwise.

Maintenance and service
11-62
OM-H0412
1) Spring
2) Connector
4. Disconnect the connector behind the case cap.
5. Release the retainer spring.
6. Replace the bulb with a new one. Then reconnect
the connectors and reinstall the removed parts in
the reverse order of removal.
Front side marker lightHGB020BA
1. Remove the front side marker light assembly by
prying the edge of the lens with a regular screwdriv-
er. At this time, use a cloth to protect the body from
being damaged by the screwdriver.
2. Remove the bulb holder from the front side mark-
er light assembly by turning it counterclockwise.
3. Pull the bulb out of the socket. Install a new bulb.
4. Set the bulb holder into the front side marker light
assembly and turn it clockwise until it locks.
5. Reinstall the front side marker light assembly
onto the side of the front fender.

Maintenance and service
11-63
– CONTINUED –
Rear combination lights
Sedan
HGB011BA
1. Remove the clip from the rear trunk trim with a
regular screwdriver.
HGB012BB
1) Backup light
2) Rear turn
signal light 3) Brake light
4) Tail light
5) Brake/tail light
2. Open the rear portion of the side trunk trim panel.
3. Remove the bulb holder from the rear combina-
tion light assembly by turning it counterclockwise.
4. Remove the bulb from the socket by pushing it
and turning counterclockwise. Install a new bulb.
5. Set the bulb holder into the rear combination light
assembly and turn it clockwise until it locks.
6. Secure the rear trunk trim panel with the clips.

Maintenance and service
11-64
Wagon
HGB013BA
1. Using a Phillips screwdriver, remove the upper
and lower screws that secure the side cover of the
rear combination light assembly.
HGB014BA
2. Remove the upper and lower screws. Then, slide
the rear combination lamp assembly to the rear and
remove it from the vehicle.

Maintenance and service
11-65
– CONTINUED –
HGB015CB
1) Tail/stop light
2) Rear turn signal light
3) Backup light
4) Rear side marker light
3. Remove the bulb holder from the rear combina-
tion light assembly by turning it counterclockwise.
4. Remove the bulb from the socket by pushing it
and turning counterclockwise. Install a new bulb.
5. Set the bulb holder into the rear combination light
assembly and turn it clockwise until it locks.
6. Close the cover and latch the lock.
7. Reinstall the rear combination light assembly and
its side cover.
License plate light
HGF012FA
1. Remove the mounting screws using a phillips
screwdriver.
2. Remove the cover and lens.
3. Pull the bulb out of the socket. Install a new bulb.
4. Reinstall the lens and cover.
5. Tighten the mounting screws.

Maintenance and service
11-66
Room light, spot light and cargo area light
HSA005BA
HBB029BA
HB0386
1) Bulb
1. Remove the lens by prying the edge of the lens
with a regular screwdriver.
2. Pull the bulb out of the socket. Install a new bulb.
3. Reinstall the lens.

Maintenance and service
11-67
– CONTINUED –
Trunk light
HG2009DA
1. Remove the cover by pulling it out.
2. Pull the bulb out of the socket. Install a new bulb.
3. Reinstall the cover.
High mount stop light
SedanOM-H2350
1. Remove the high mount stop light cover by pry-
ing the edge with a screwdriver.
2. Pull the bulb out of the socket. Install a new bulb.
3. Reinstall the cover.

Maintenance and service
11-68
Wagon
HBB028BA
1. Remove the mounting screw covers by prying
the edge with a screwdriver.
2. Remove the mounting screws using a phillips
screwdriver and then remove the high mount stop
light cover.
3. Remove the bulbs from the socket by pushing it
and turning counterclockwise. Install a new bulb.
4. Reinstall the cover.
5. Tighten the mounting screws then reinstall the covers. NOTE
Other bulbs may be difficult to replace. Have your
SUBARU dealer replace these bulbs if necessary.

Specifications
12-6
Fuses and circuits Fuse panel located behind the coin tray
HS0224
Fuse panelFuse ratingCircuit
115AHeater fan
215AHeater fan
315APower door lock
Keyless entry
420ACigarette lighter
Remote controlled rear view mirrors
510ATail light
Parking light
615ASRS airbag
715AFog light
820AABS solenoid
915ARadio
10Empty
1115AEngine ignition sys- tem
SRS airbag
AT control system

Specifications
12-7
– CONTINUED –
Fuse panelFuse ratingCircuit
1210AIllumination bright- ness control
1310ACombination meter
SRS lamp
1410ARear window wiper and washer
1530AWindshield wiper and washer
1620ABrake light
1715AAir conditioner
1815ABackup light
Cruise control
1920AMirror heater