brake rotor SUBARU LEGACY 1999 Service Repair Manual

No. Part Name Part Number Dimension mm (in) Application
1 Rotor (Oil pump)15008AA060
15008AA070
15008AA08011.37 Ð 11.38 (0.4476 Ð 0.4480)
11.38 Ð 11.39 (0.4480 Ð 0.4484)
11.39 Ð 11.40 (0.4484 Ð 0.4488)Adjusting side clearance of oil
pump
2 Thrust bearing806528050
806528060
806528070
806528080
806528090
8065281004.11 (0.1618)
4.3 (0.169)
4.5 (0.177)
4.7 (0.185)
4.9 (0.193)
5.1 (0.201)Adjusting total end play
3Retaining plate
(High clutch)31567AA710
31567AA720
31567AA730
31567AA740
31567AA670
31567AA680
31567AA690
31567AA7004.7 (0.185)
4.8 (0.189)
4.9 (0.193)
5.0 (0.197)
5.1 (0.201)
5.2 (0.205)
5.3 (0.209)
5.4 (0.213)Adjusting clearance of high
clutch
4Retaining plate
(Reverse clutch)31567AA750
31567AA760
31567AA770
31567AA780
31567AA790
31567AA800
31567AA810
31567AA8203.8 (0.150)
4.0 (0.157)
4.2 (0.165)
4.4 (0.173)
4.6 (0.181)
4.8 (0.189)
5.0 (0.197)
5.2 (0.205)Adjusting clearance of reverse
clutch
5Retaining plate
(2-4 brake)31567AA610
31567AA620
31567AA630
31567AA640
31567AA650
31567AA6605.6 (0.220)
5.8 (0.228)
6.0 (0.236)
6.2 (0.244)
6.4 (0.252)
6.6 (0.260)Adjusting clearance of 2-4
brake
6Retaining plate
(Low clutch)31567AA830
31567AA840
31567AA850
31567AA860
31567AA8703.8 (0.150)
4.0 (0.157)
4.2 (0.165)
4.4 (0.173)
4.6 (0.181)Adjusting clearance of low
clutch
7Retaining plate
(Low and reverse
brake)31667AA320
31667AA330
31667AA340
31667AA350
31667AA360
31667AA370
31667AA3804.2 (0.165)
4.5 (0.177)
4.8 (0.189)
5.1 (0.201)
5.4 (0.213)
5.7 (0.224)
6.0 (0.236)Adjusting clearance of low
and reverse brake
8Pressure plate
(Transfer clutch)31593AA151
31593AA161
31593AA171
31593AA1813.3 (0.130)
3.7 (0.146)
4.1 (0.161)
4.5 (0.177)Adjusting clearance of transfer
clutch
9Thrust bearing
(Transfer clutch)806536020
806535030
806535040
806535050
806535060
806535070
8065350903.8 (0.150)
4.0 (0.157)
4.2 (0.165)
4.4 (0.173)
4.6 (0.181)
4.8 (0.189)
5.0 (0.197)Adjusting end play of transfer
clutch
10Washer
(Front differential)803038021
803038022
8030380230.95 (0.0374)
1.00 (0.0394)
1.05 (0.0413)Adjusting backlash of differen-
tial bevel gear
7
[S1B0]3-2SPECIFICATIONS AND SERVICE DATA
1. Automatic Transmission and Differential

1. Front Axle
A: REMOVAL
1) Disconnect ground cable from battery.
2) Jack-up vehicle, support it with safety stands,
and remove front wheels.
3) Unlock axle nut.
G4M0214
4) Remove axle nut using a socket wrench.
CAUTION:
Be sure to loose and retighten axle nut after
removing wheel from vehicle. Failure to follow
this rule may damage wheel bearings.
5) Remove stabilizer link.
G4M0215
6) Remove DOJ/SFJ from transmission spindle.7) Remove front drive shaft assembly from hub. If
it is hard to remove, use STs.
ST1 926470000 AXLE SHAFT PULLER
ST2 927140000 PLATE
CAUTION:
IBe careful not to damage oil seal lip when
removing front drive shaft.
IWhen replacing front drive shaft, also
replace inner oil seal.
G4M0216
8) Remove disc brake caliper from housing, and
suspend it from strut using a wire.
9) Remove disc rotor from hub.
If disc rotor seizes up within hub, drive disc rotor
out by installing an 8-mm bolt in screw hole on the
rotor.
G4M0217
10) Remove cotter pin and castle nut which
secure tie-rod end to housing knuckle arm.
G4M0218
9
[W1A0]4-2SERVICE PROCEDURE
1. Front Axle

12) Attach hub to ST1 securely.
13) Clean dust or foreign particles from the pol-
ished surface of hub.
14) sing ST2, press bearing into hub by driving
inner race.
ST1 927080000 HUB STAND
ST2 927120000 HUB INSTALLER
G4M0235
E: INSTALLATION
1) Install transverse link ball joint to housing.
Tightening torque:
44
±6 N´m (4.5±0.6 kg-m, 32.5±4.3 ft-lb)
2) While aligning alignment mark on camber
adjusting bolt head, connect housing and strut.
CAUTION:
Use a new self-locking nut.
Tightening torque:
147
±15 N´m (15±1.5 kg-m, 108±11 ft-lb)
3) Install speed sensor and harness on housing
(only vehicle equipped with ABS).
4) Install disc rotor on hub.
5) Install disc brake caliper on housing.
Tightening torque:
59
±10 N´m (6±1 kg-m, 43±7 ft-lb)
6) Install front drive shaft.
7) Connect stabilizer link.8) Install tie-rod end ball joint on housing knuckle
arm.
Tightening torque:
27.0
±2.5 N´m (2.75±0.25 kg-m, 19.9±1.8
ft-lb)
G4M0236
9) While depressing brake pedal, tighten axle nut
and lock it securely.
CAUTION:
IUse a new axle nut.
IAlways tighten axle nut before installing
wheel on vehicle. If wheel is installed and
comes in contact with ground when axle nut is
loose, wheel bearings may be damaged.
IBe sure to tighten axle nut to specified
torque. Do not overtighten it as this may dam-
age wheel bearing.
Tightening torque:
186
±20 N´m (19±2 kg-m, 137±14 ft-lb)
G4M0237
10) After tightening axle nut, lock it securely.
G4M0238
13
[W1E0]4-2SERVICE PROCEDURE
1. Front Axle

11) Install wheel and tighten wheel nuts to speci-
fied torque.
Tightening torque:
88
±10 N´m (9±1 kg-m, 65±7 ft-lb)
2. Rear Axle
A: REMOVAL
1. DISC BRAKE
1) Disconnect ground cable from battery.
2) Jack-up vehicle, and remove rear wheel cap
and wheels.
CAUTION:
Be sure to loosen and retighten axle nut after
removing wheel from vehicle. Failure to follow
this rule may damage wheel bearings.
3) Unlock axle nut.
4) Remove axle nut using a socket wrench.
5) Return parking brake lever and loosen adjust-
ing nut.
B4M0050A
6) Remove disc brake caliper from back plate, and
suspend it from strut using a piece of wire.
G4M0240
7) Remove disc rotor from hub.
NOTE:
If disc rotor seizes up within hub, drive it out by
installing an 8-mm bolt into bolt hole in disc rotor.
14
4-2[W2A1]SERVICE PROCEDURE
2. Rear Axle

11) Install wheel and tighten wheel nuts to speci-
fied torque.
Tightening torque:
88
±10 N´m (9±1 kg-m, 65±7 ft-lb)
2. Rear Axle
A: REMOVAL
1. DISC BRAKE
1) Disconnect ground cable from battery.
2) Jack-up vehicle, and remove rear wheel cap
and wheels.
CAUTION:
Be sure to loosen and retighten axle nut after
removing wheel from vehicle. Failure to follow
this rule may damage wheel bearings.
3) Unlock axle nut.
4) Remove axle nut using a socket wrench.
5) Return parking brake lever and loosen adjust-
ing nut.
B4M0050A
6) Remove disc brake caliper from back plate, and
suspend it from strut using a piece of wire.
G4M0240
7) Remove disc rotor from hub.
NOTE:
If disc rotor seizes up within hub, drive it out by
installing an 8-mm bolt into bolt hole in disc rotor.
14
4-2[W2A1]SERVICE PROCEDURE
2. Rear Axle

11) Using ST1 and ST2, press bearing into hub.
ST1 927080000 HUB STAND
ST2 927450000 HUB INSTALLER
G4M0262
E: INSTALLATION
1. DISC BRAKE
1) Connect rear housing assembly and strut
assembly.
CAUTION:
Use a new self-locking nut.
Tightening torque:
147
±15 N´m (15±1.5 kg-m, 108±11 ft-lb)
2) Fit BJ (bell joint) to rear housing splines.
CAUTION:
Be careful not to damage inner oil seal lip.
3) Connect rear housing assembly to lateral link
assembly.
CAUTION:
Use a new self-locking nut.
Tightening torque:
137
±20 N´m (14±2 kg-m, 101±14 ft-lb)
G4M0245
4) Connect rear housing assembly to trailing link
assembly.
CAUTION:
Use a new self-locking nut.
Tightening torque:
98 Ð 127 N´m (10 Ð 13 kg-m, 72 Ð 94
ft-lb)
G4M0246
5) Connect parking brake cable to parking brake.
6) Install disc rotor on rear housing assembly.
7) Install disc brake caliper on back plate.
Tightening torque:
52
±6 N´m (5.3±0.6 kg-m, 38.3±4.3 ft-lb)
G4M0240
8) Install rear speed sensor to back plate (only
vehicle equipped with ABS).
G4M0266
9) Bleed air from brake system. [W11B0].>
10) Adjust parking brake lever stroke by turning
adjuster.
11) Move brake lever back to apply brakes. While
depressing brake pedal, tighten axle nut using a
20
4-2[W2E1]SERVICE PROCEDURE
2. Rear Axle

1. Front Disc Brake
A: EXCEPT 2500 cc MODEL
B4M1152C
(1) Caliper body
(2) Air bleeder screw
(3) Guide pin (Green)
(4) Pin boot
(5) Piston seal
(6) Piston
(7) Piston boot
(8) Lock pin (Yellow)(9) Support
(10) Pad clip
(11) Outer shim
(12) Inner shim
(13) Pad (Outside)
(14) Pad (Inside)
(15) Disc rotor
(16) Disc coverTightening torque: N´m (kg-m, ft-lb)
T1:
8±1 (0.8±0.1, 5.8±0.7)
T2:18±5 (1.8±0.5, 13.0±3.6)
T3:37±5 (3.8±0.5, 27.5±3.6)
T4:78±10 (8.0±1.0, 58±7)
6
4-4[C1A0]COMPONENT PARTS
1. Front Disc Brake

B: 2500 cc MODEL
B4M1151C
(1) Caliper body
(2) Air bleeder screw
(3) Guide pin (Green)
(4) Pin boot
(5) Piston seal
(6) Piston
(7) Piston boot
(8) Boot ring(9) Lock pin (Yellow)
(10) Support
(11) Pad clip
(12) Outer shim
(13) Inner shim
(14) Pad (Outside)
(15) Pad (Inside)
(16) Disc rotor(17) Disc cover
Tightening torque: N´m (kg-m, ft-lb)
T1:
8±1 (0.8±0.1, 5.8±0.7)
T2:18±5 (1.8±0.5, 13.0±3.6)
T3:37±5 (3.8±0.5, 27.5±3.6)
T4:78±10 (8.0±1.0, 58±7)
7
[C1B0]4-4COMPONENT PARTS
1. Front Disc Brake

2. Rear Disc Brake
B4M0066B
(1) Lock pin
(2) Lock pin sleeve
(3) Lock pin boot
(4) Air bleeder screw
(5) Caliper body
(6) Guide pin
(7) Guide pin boot
(8) Piston seal
(9) Piston
(10) Piston boot
(11) Boot ring
(12) Support
(13) Shim
(14) Inner shim
(15) Inner pad(16) Pad clip
(17) Outer pad
(18) Outer shim
(19) Shoe hold-down pin
(20) Cover
(21) Back plate
(22) Retainer
(23) Spring washer
(24) Parking brake lever
(25) Parking brake shoe (Secondary)
(26) Parking brake shoe (Primary)
(27) Adjusting spring
(28) Strut
(29) Strut shoe spring
(30) Shoe guide plate(31) Secondary shoe return spring
(32) Primary shoe return spring
(33) Adjuster
(34) Shoe hold-down cup
(35) Shoe hold-down spring
(36) Disc rotor
Tightening torque: N´m (kg-m, ft-lb)
T1:
8±1 (0.8±0.1, 5.8±0.7)
T2:20±4 (2.0±0.4, 14.5±2.9)
T3:26±5 (2.7±0.5, 19.5±3.6)
T4:52±6 (5.3±0.6, 38.3±4.3)
8
4-4[C200]COMPONENT PARTS
2. Rear Disc Brake

1. Front Disc Brake
A: ON-CAR SERVICE
1. PAD
1) Remove lock pin.
2) Raise caliper body.
3) Remove pad.
B4M1167
4) Check pad thickness A.
B4M1168A
Pad thickness
(including back metal)
mm (in)Standard value 17 (0.67)
Wear limit 7.5 (0.295)
CAUTION:
IAlways replace the pads for both the left and
right wheels at the same time. Also replace pad
clips if they are twisted or worn.
IA wear indicator is provided on the inner
disc brake pad. If the pad wears down to such
an extent that the end of the wear indicator
contacts the disc rotor, a squeaking sound is
produced as the wheel rotates. If this sound is
heard, replace the pad.
IReplace pad if there is oil or grease on it.5) Apply thin coat of PBC GREASE (Part No.
003607000) to the frictional portion between pad
and pad clip.
B4M1169A
6) Install pads on support.
7) Install caliper body on support.
NOTE:
If it is difficult to push piston during pad
replacement, loosen air bleeder to facilitate work.
2. DISC ROTOR
1) Install disc rotor by tightening the five wheel
nuts.
2) Set a dial gauge on the disc rotor. Turn disc
rotor to check runout.
G4M0364
NOTE:
Make sure that dial gauge is set 5 mm (0.20 in)
inward of rotor outer perimeter.
Disc rotor runout limit:
0.075 mm (0.0030 in)
18
4-4[W1A1]SERVICE PROCEDURE
1. Front Disc Brake