roof SUBARU TRIBECA 2009 1.G Service User Guide

EI-34
Roof Molding
EXTERIOR/INTERIOR TRIM
11.Roof Molding
A: REMOVAL
1) Turn over the edge of the roof molding, and re-
move the inside clips with flat tip screwdriver by
sliding as arrow indicates.
Right side: slide towards the front of the vehicle.
Left side: slide towards the rear of the vehicle.
2) Pull the roof molding upward, and remove it from
vehicle body.
3) Remove the roof trim. LATION, Roof Trim.>
4) Remove the nuts, and remove the roof carrier at-
tachment.
B: INSTALLATION
1) Install the roof carrier attachment.
Tightening torque:
7.5 N·m (0.77 kgf-m, 5.53 ft-lb)
2) Remove each clip from the roof molding, and in-
stall them to the vehicle side.
CAUTION:
Always replace clips damaged during removal
of the roof moulding with new clips.
3) Push the front edge of roof molding against the
front window, and install the positioning clip on the
front end to the rivet on the vehicle side.
EI-00509
EI-01380
(1) Windshield
(2) Positioning clips
(3) Roof molding
(4) Rivet
(5) Clip
EI-00659
EI-01381
(2)
(1)
(4)(5)
(3)

EI-49
Assist Grip
EXTERIOR/INTERIOR TRIM
22.Assist Grip
A: REMOVAL
1) Remove the screw cover, and remove the screw
inside.
2) Pull the left side of assist grip toward you, and ro-
tate the right side of it counterclockwise to remove.
3) Remove the roof trim. AL, Roof Trim.>
4) Remove the bolts, and remove the assist grip
bracket.
B: INSTALLATION
Install in the reverse order of removal.
CAUTION:
Be sure to install the grommet to assist grip
bracket.
When the assist grip is installed with no grom-
met, it ill cause the grip to not return properly.
(A) Grommet
EI-00809
EI-01065
(A)

EI-50
Roof Trim
EXTERIOR/INTERIOR TRIM
23.Roof Trim
A: REMOVAL
1) Disconnect the ground cable from battery.
2) Remove the spot map light. MOVAL, Spot Map Light.>
3) Remove the room light or rear entertainment
(model with rear entertainment system). LI-30, REMOVAL, Room Light.>
4) Remove the sun visor. AL, Sun Visor.>
5) Remove the assist grip. AL, Assist Grip.>
6) Remove the front pillar upper trim and center pil-
lar upper trim. Trim.>
7) Remove the rear quarter upper trim. 45, REMOVAL, Rear Quarter Trim.>
8) Remove the sunroof opening trim.
9) Remove the clips and each harness, pull out the
rear center seat belt, and remove the roof trim.
B: INSTALLATION
Install in the reverse order of removal.
EI-00501
EI-01354

GW-28
Sun Roof Glass
GLASS/WINDOWS/MIRRORS
19.Sun Roof Glass
A: REMOVAL

B: INSTALLATION

C: ADJUSTMENT

AC-46
Air Vent Grille
HVAC SYSTEM (HEATER, VENTILATOR AND A/C)
25.Air Vent Grille
A: REMOVAL
1. UPPER GRILL
1) Disconnect the ground cable from battery.
2) Lift the upper grill, and remove the catch on the
hazard switch side.
3) Hold the side of the monitor and remove the
catch on the upper, right and left sides.
4) Detach the connectors and remove the panel.
2. CENTER GRILLE
1) Disconnect the ground cable from battery.
2) Remove the front control panel. FRONT, REMOVAL, Control Panel.>
3) Remove the screw, and remove the center grill
3. SIDE GRILLE
Remove the catch in 2 locations to remove the side
air vent grill.
4. ROOF GRILL
Remove the catch, and remove the roof air vent
grill.
B: INSTALLATION
Install in the reverse order of removal.
C: INSPECTION
1) Check that the direction and amount of air can
be adjusted smoothly.
2) Check that the adjustment can be maintained in
each position.
AC-01345
AC-01346
AC-01347
AC-01309
AC-001354

AC-48
Heater Vent Duct
HVAC SYSTEM (HEATER, VENTILATOR AND A/C)
27.Heater Vent Duct
A: REMOVAL
1. INSTRUMENT
1) Remove the instrument panel. REMOVAL, Instrument Panel Lower Cover.>
2) Remove the screws and detach the center vent
duct (A).
3) Remove the screws and detach the side vent
duct (B).
4) Remove the screws and detach the side defrost-
er duct (C).
2. ROOF DUCT
Remove the roof trim. Roof Trim.>
NOTE:
The roof duct is one piece with the roof trim. If it re-
quires replacement, replace the roof trim.
B: INSTALLATION
Install in the reverse order of removal.
AC-01352
(C)(B)
(C)
(A)

AC(diag)-5
General Description
HVAC SYSTEM (AUTO A/C) (DIAGNOSTICS)
4) Inspection of the rear cooler switch
5) Inspection of rear cooler
6) Inspection of illumination control
No. Point to check Switch operation Judgment standard
1FAN switch Turn the FAN switch.
Blower fan switches OFF → LO → ML → MH
→ HI each time turning the switch and it
switches in reverse order when turned back-
ward.
No. Point to check Switch operation Judgment standard
1Roof grill Turn the FAN switch.
Fr on t A / C O N ( co mp r es so r op e rat i ng ) : COOL
Fr on t A / C O FF ( co mp r e ss or n ot o pe ra t in g) :
Blower ON
No. Point to check Switch operation Judgment standard
1Illumination Turn the lighting switch to ON. Illumination comes on.

LI-28
High-mounted Stop Light
LIGHTING SYSTEM
26.High-mounted Stop Light
A: REMOVAL
1) Disconnect the ground cable from battery.
2) Detach the roof spoiler. AL, Roof Spoiler.>
3) Remove the nuts (A), then detach the high-
mounted stop light.
B: INSTALLATION
Install in the reverse order of removal.
C: INSPECTION
1) Install the high-mounted stop light to test if it illu-
minates normally.
2) If the high-mounted stop light does not illumi-
nate, replace it with a new one.
NOTE:
Since LEDs (Light Emitting Diodes) are used for
the high-mounted stop light, replace the high-
mounted stop light assembly when the LEDs went
out.
LI-00312
(A)(A)

SB-12
Second Seat Belt
SEAT BELT SYSTEM
6. Second Seat Belt
A: REMOVAL
1. OUTER SEAT BELT RH ASSEMBLY AND
LH ASSEMBLY
1) Remove the second row seats. REMOVAL, Second-row Seats.>
2) Remove the third-row seats. REMOVAL, Third-row Seats.>
3) Remove the rear quarter trim. REMOVAL, Rear Quarter Trim.>
4) Remove the lower anchor bolt.
5) Remove the bolt to remove outer seat belt re-
tractor.
2. SHOULDER SEAT BELT CENTER AS-
SEMBLY
1) Remove the rear quarter trim. REMOVAL, Rear Quarter Trim.>
2) Remove the cover (A) from roof trim, and then
insert it to the inside of roof trim.
3) Remove the clips, and then lower the roof trim
end.
CAUTION:
When removing the roof trim clip, do not pull
the roof trim end backward with excessive
force, otherwise roof trim may be damaged.
4) Remove the bolt to remove the seat belt retrac-
tor.
3. INNER SEAT BELT RH ASSEMBLY
1) Remove the RH second-row seat assembly.
ond-row Seats.>
2) Remove the LH hinge outer cover.
3) Remove the bolt, and then detach the inner belt
assembly.
SB-00308
SB-00309
SB-00236
(A)
SB-00155
SB-00316
SB-00310

SR-2
General Description
SUNROOF/T-TOP/CONVERTIBLE TOP (SUNROOF)
1. General Description
A: COMPONENT
(1) Glass lid (5) Drain tubeTightening torque: N·m (kgf-m, ft-lb)
(2) Weather strip (6) Motor ASSYT1: 4.5 (0.46, 3.3)
(3) Cover (7) Frame ASSYT2: 6.0 (0.61, 4.4)
(4) Sunshade (8) Deflector
SR-00125
(1)
(2)
(3)
(4)
(5)
(5)
(6)
(7)
T1(8)
T2
T2
T2