torque SUBARU TRIBECA 2009 1.G Service User Guide

AB-25
Front Sub Sensor
AIRBAG SYSTEM
12.Front Sub Sensor
A: REMOVAL
1) Turn the ignition switch to OFF.
2) Disconnect the ground cable from battery and
wait for at least 20 seconds before starting work.
3) Remove the front bumper face. FRONT BUMPER FACE, REMOVAL, Front
Bumper.>
4) Remove the bolt, and then detach the front sub
sensor.
5) Disconnect the connector from front sub sensor.
B: INSTALLATION
CAUTION:
•Do not reuse the bolt and nut.
•Always use new bolts and nuts for them.
Install in the reverse order of removal.
Tightening torque:
13 N·m (1.32 kgf-m, 9.6 ft-lb)
C: INSPECTION
Check for the following, and replace the damaged
parts with new parts.
•Front sub sensor, mounting bracket and connec-
tor are damaged.
•Airbag is deployed.
AB-00636

EB-7
General Description
EXTERIOR BODY PANELS
B: COMPONENT
1. FRONT HOOD
(1) Front hood panel (6) Front hood release handle ASSYTightening torque: N·m (kgf-m, ft-lb)
(2) Front hood insulator (7) Front grille weatherstripT1: 7.5 (0.76, 5.5)
(3) Front hood hinge T2: 20 (2.04, 14.5)
(4) Front hood damper T3: 24.5 (2.5, 18.1)
(5) Front hood weather strip T4: 33 (3.4, 24.5)
EB-00273
T3
T1
T3
T2
(2)
(3)
(4)
(5)
(1)
T4
(6)
(7)

EB-8
General Description
EXTERIOR BODY PANELS
2. FRONT FENDER PANEL
Tightening torque: N·m (kgf-m, ft-lb)
T: 7.4 (0.75, 5.5)
EB-00274
T
T
T
T

EB-9
General Description
EXTERIOR BODY PANELS
3. FRONT DOOR PANEL
(1) Front door panel (6) Lower hingeTightening torque: N·m (kgf-m, ft-lb)
(2) Sealing cover T1: 7.4 (0.75, 5.5)
(3) Front door weather strip T2: 24.5 (2.5, 18.1)
(4) Checker T3: 29.4 (3.0, 21.7)
(5) Upper hinge T4: 32.3 (3.3, 23.8)
EB-00289
T4
T1
T3
T2
T3
T2
(6)
(2)
(5)
(1)
(3)
(4)

EB-10
General Description
EXTERIOR BODY PANELS
4. REAR DOOR PANEL
(1) Rear door panel (6) Lower hingeTightening torque: N·m (kgf-m, ft-lb)
(2) Sealing cover T1: 7.4 (0.75, 5.5)
(3) Rear door weather strip T2: 24.5 (2.5, 18.1)
(4) Checker T3: 29.4 (3.0, 21.7)
(5) Upper hinge T4: 32.3 (3.3, 23.8)
EB-00290
T1
T3
T2
(5)
(1)
T3
T2(6)
T4
(4)
(2)
(3)

EB-11
General Description
EXTERIOR BODY PANELS
5. REAR GATE PANEL
C: CAUTION
•Exterior body panels are heavy. Do not drop and
damage the panels. During removal and installa-
tion, do not damage the panel painting surface.
•While removing mounting bolts, using assistance
devices such as a support jack will help support the
panel.
•Be careful not to lose small parts.
(1) Rear gate damper stay Tightening torque: N·m (kgf-m, ft-lb)
(2) Hinge T1: 10 (1.02, 7.2)
(3) Rear gate panel T2: 20 (2.04, 14.5)
T3: 25 (2.6, 18.4)
EB-00277
(3)
T3
T3
T1
T2
(2)
(1)

EB-14
Front Hood
EXTERIOR BODY PANELS
4) Remove the front fender. MOVAL, Front Fender.>
5) Remove the bolts of front hood hinge.
5. FRONT HOOD STRIKER
Refer to the front hood lock assembly of SL section.
Assembly.>
6. FRONT HOOD PANEL
1) Remove the front hood insulator.
2) Open the front hood to remove the window
washer hose.
3) Remove the front hood weather strip.
4) Remove the hood lock assembly.
sembly.>
5) Remove the window washer hose and nozzle.
zle.>
6) Remove the front hood damper.
7) Remove the bolt, and remove the front hood
panel from the front hood hinge.
B: INSTALLATION
Install in the reverse order of removal.
NOTE:
Be careful not to catch the window washer hose in.
Tightening torque:
Refer to “COMPONENT” of “General Descrip-
tion”. NENT, General Description.>
C: ADJUSTMENT
1) Adjust the clearance between front hood panel
and front fender panel. Clearance must be equal at
both sides. For the dimension of clearance, refer to
“SPECIFICATION” in “General Description”. to EB-2, SPECIFICATION, General Description.>
2) Use the hinge mounting bolts to align the front
hood longitudinal and lateral position.
3) Adjust the height at the front end of hood. to SL-44, ADJUSTMENT, Front Hood Lock Assem-
bly.>
4) Rotate the hood buffer to adjust lateral height.
D: DISPOSAL
For the disposal procedures of front hood damper
stay, refer to the disposal procedures of rear gate
damper stay. Gate.>
EB-00286
EB-00285
EB-00285
EB-00287

EB-15
Front Fender
EXTERIOR BODY PANELS
3. Front Fender
A: REMOVAL
1) Disconnect the ground cable from battery.
2) Remove the side sill guarnish. REMOVAL, Side Garnish.>
3) Remove the front bumper. MOVAL, Front Bumper.>
4) Remove the headlight assembly. REMOVAL, Headlight Assembly.>
5) Remove the mud guard. MOVAL, Mud Guard.>
6) Remove the cowl panel side.
7) Remove the bolt, and remove the front fender
panel.
B: INSTALLATION
1) Install in the reverse order of removal.
2) Install with attention to make uniform clearance
between front fender panel and front hood panel.
For the dimension of clearance, refer to “SPECIFI-
CATION” in “General Description”. SPECIFICATION, General Description.>
Tightening torque:
7.4 N·m (0.75 kgf-m, 5.5 ft-lb)
EI-01280
(A)
EB-00279

EB-17
Front Door
EXTERIOR BODY PANELS
B: INSTALLATION
1) Put a wooden block on jack and place the front
door on that.
2) Apply grease to the sliding area of door hinges,
and install the door hinge to vehicle.
3) Install the front door to upper hinge and lower
hinge adjusting by jack.
4) Tighten bolt of door checker.
5) Connect door harness connector, and install the
instrument panel lower cover.
6) Install the front pillar lower trim.
Tightening torque:
Refer to “COMPONENT” of “General Descrip-
tion”.
PONENT, General Description.>
C: ADJUSTMENT
1) Using the ST, loosen the body-side bolts of up-
per and lower hinges to align the position for verti-
cal and horizontal direction of the front door panel.
ST 925610000 DOOR HINGE WRENCH
2) Loosen the screw (A) and tap striker (B) using
plastic hammer to adjust the gap between rear end
surface of front door panel and front end surface of
rear door.
CAUTION:
Do not use an impact wrench. Welding area on
the striker nut plate is easily broken.
EB-00013
EB-00016
ST
EB-00017
(B)(A)

EB-20
Rear Door
EXTERIOR BODY PANELS
B: INSTALLATION
1) Put a wooden block on jack and place the rear
door on that.
2) Apply grease to the moving part of door hinges.
3) Install the rear door to upper hinge and lower
hinge adjusting by jack.
4) Tighten bolt of door checker.
5) Connect the door harness connector.
Tightening torque:
Refer to “COMPONENT” of “General Descrip-
tion”.
PONENT, General Description.>
C: ADJUSTMENT
1) Open the rear door, loosen the door-side bolts of
upper and lower hinges to align the position for ver-
tical and horizontal direction of rear door panel.
2) Loosen the screw (A) and tap striker (B) using
plastic hammer to adjust the gap between rear end
surface of rear door panel and body surface.
CAUTION:
Do not use an impact wrench. Welding area on
the striker nut plate is easily broken.
EB-00013
EB-00015
EB-00017
(B)(A)