bulkhead SUBARU TRIBECA 2009 1.G Service Workshop Manual

AB(diag)-35
Subaru Select Monitor
AIRBAG SYSTEM (DIAGNOSTICS)
2. WITHOUT DTC
DETECTING CONDITION:
•Defective combination meter
•Open circuit of harness
TROUBLE SYMPTOM:
•Airbag warning light remains on.
•“NO TROUBLE CODE” will be displayed on the Subaru Select Monitor.
For detailed operation procedure, refer to “Airbag Warning Light Failure”. ing Light Failure.>
NOTE:
•For detailed operation procedure, refer to “Airbag Warning Light Failure”. Warning Light Failure.>
•When the airbag warning light is OFF and “NO TROUBLE CODE” is displayed on Subaru Select Monitor,
the system is in normal condition.
9CHECK THE HARNESS BETWEEN THE AIR-
BAG CONTROL MODULE AND DATA LINK
CONNECTOR.
1) Turn the ignition switch to OFF, disconnect
the battery ground cable, and wait more than
20 seconds.
2) Disconnect the connector (AB6) from air-
bag control module.
3) Connect the connector (1U) in the test har-
ness U to connector (AB6).
4) Measure the resistance between connector
(4U) in the test harness U and the data link
connector.
Connector & terminal
(4U) No. 18 — (B40) No. 10:
Is the resistance less than 10
Ω?
Go to step 10.Repair the har-
ness between the
airbag control
module and the
data link connec-
tor. Or replace the
airbag main har-
ness with the bulk-
head harness.
10 CHECK POWER SUPPLY CIRCUIT.
1) Turn the ignition switch to ON.
2) Measure the voltage between connector
(2U) in the test harness U and chassis ground.
Connector & terminal
(2U) No. 1 — Chassis ground:
(2U) No. 6 — Chassis ground:
Is the voltage more than 10 V? Go to step 11.Repair the har-
ness between the
airbag control
module and the
battery. Or replace
the airbag main
harness with the
bulkhead harness.
11 CHECK BETWEEN THE AIRBAG CONTROL
MODULE AND CHASSIS GROUND.
1) Turn the ignition switch to OFF.
2) Measure the resistance between connector
(2U) in the test harness U and chassis ground.
Connector & terminal
(2U) No. 10 — Chassis ground:
(2U) No. 11 — Chassis ground:
Is the resistance less than 10
Ω?
Go to step 12.Repair the har-
ness between the
airbag control
module and the
chassis ground. Or
replace the airbag
main harness with
the bulkhead har-
ness.
12 CHECK POOR CONTACT OF CONNECTOR.Is there poor contact in the
control module power supply,
ground circuit and data link
connector?
Repair the con-
nector. (Replace
the harness with-
out repairing the
airbag system
connector.)
Replace the only
airbag control
module. AB-21, REMOVAL,
Airbag Control
Module.>
Step Check Yes No

AB(diag)-41
Airbag Warning Light Failure
AIRBAG SYSTEM (DIAGNOSTICS)
Step Check Yes No
1READ DTC.
Read the DTC. DIAGNOSTIC TROUBLE CODE (DTC),
OPERATION, Subaru Select Monitor.>
Is DTC displayed? Perform the diag-
nosis according to
DTC.
Go to step 2.
2CHECK POOR CONTACT.
1) Turn the ignition switch to OFF, disconnect
the battery ground cable, and wait more than
20 seconds.
2) Confirm that there is solid connection
between the airbag control module and con-
nector (AB6).
Is there poor contact in con-
nector (AB6)?
If the poor contact
of the connector is
not fixed, replace
the airbag main
harness with body
harness or replace
the airbag control
module. AB-21, Airbag
Control Module.>
Go to step 3.
3CHECK AIRBAG MAIN HARNESS.
1) Remove the instrument panel lower cover
and disconnect the connectors (AB7) and
(AB2).
2) Remove the console side cover lower on
the passenger's side and disconnect the con-
nectors (AB10) and (AB9).
3) Disconnect the connector (AB6) from air-
bag control module, and connect the connector
(1U) in the test harness U.
4) Connect the battery ground terminal and
turn the ignition switch to ON.
5) Connect the connectors (7U) and (8U) in
the test harness U.
NOTE:After the fault has been cleared, disconnect the
connectors (7U) and (8U).
Does the airbag warning light
go off?
Go to step 4.Go to step 5.
4CHECK GROUND CIRCUIT.
1) Turn the ignition switch to OFF, disconnect
the battery ground cable, and wait more than
20 seconds.
2) Disconnect the connector (AB6) from air-
bag control module.
3) Connect the connector (1U) in the test har-
ness U to body harness connector (AB6).
4) Measure the resistance between connector
(2U) in the test harness U and chassis ground.
Connector & terminal
(2U) No. 10 — Chassis ground:
(2U) No. 11 — Chassis ground:
Is the resistance less than 10
Ω?
Replace the airbag
control module.
Airbag Control
Module.>
Repair the chas-
sis ground circuit.
5CHECK AIRBAG MAIN HARNESS AND
BULKHEAD HARNESS.
1) Disconnect the connectors (7U) and (8U).
2) Remove the combination meter.
3) Measure the resistance between connector
(i11) and connector (2U) in the test harness U.
Connector & terminal
(2U) No. 7 — (i11) No. 12:
Is the resistance less than 10
Ω?
Check the combi-
nation meter.
Go to step 6.

AB(diag)-42
Airbag Warning Light Failure
AIRBAG SYSTEM (DIAGNOSTICS)
6CHECK POOR CONTACT OF CONNEC-
TORS (AB1) AND (B31).
1) Turn the ignition switch to OFF, disconnect
the battery ground terminal, and wait more
than 20 seconds.
2) Confirm that there is firm contact between
connectors (AB1) and (B31).
Is there poor contact between
connectors (AB1) and (B31)?
Repair the bulk-
head harness or
replace the airbag
main harness with
body harness.
Go to step 7.
7CHECK AIRBAG MAIN HARNESS.
Check the airbag main harness for defect.
Is there any defect in the air-
bag main harness?
Replace the airbag
main harness with
bulkhead harness.
Repair the bulk-
head harness.
Step Check Yes No

AB(diag)-44
Airbag Warning Light Failure
AIRBAG SYSTEM (DIAGNOSTICS)
Step Check Yes No
1CHECK COMBINATION METER.
Tu r n t h e i g n i t i o n s w i t c h t o O N , a n d c o n f i r m t h a t
warning light of combination meter is turned
on.
Do warning lights except for
airbag turn on?
Go to step 2.Check the combi-
nation meter.
2CHECK DTC.
Read the DTC. DIAGNOSTIC TROUBLE CODE (DTC),
OPERATION, Subaru Select Monitor.>
Is DTC displayed? Perform the diag-
nosis according to
DTC.
Go to step 3.
3CHECK FUSE NO. 5 (IN MAIN FUSE BOX).
Remove the fuse No. 5 and perform visual
inspection.
Is the fuse No. 5 (in main fuse
box) blown out?
Replace the fuse
No. 5. If the fuse
No. 5 is blown out
again, go to step
4.
Go to step 4.
4CHECK AIRBAG WARNING LIGHT CIRCUIT
(IN COMBINATION METER).
1) Turn the ignition switch to OFF, disconnect
the battery ground cable, and wait more than
20 seconds.
2) Disconnect the connector (AB1) from
(B31).
3) Connect the battery ground terminal and
turn the ignition switch to ON.
Does airbag warning light turn
on?
Go to step 5.Check the combi-
nation meter.
5CHECK AIRBAG MAIN HARNESS.
1) Turn the ignition switch to OFF, disconnect
the battery ground cable, and wait more than
20 seconds.
2) Connect the connector (AB1) to (B31).
3) Disconnect the connector (AB6) from air-
bag control module.
4) Connect the battery ground terminal and
turn the ignition switch to ON.
Does airbag warning light turn
on?
Replace the airbag
control module.
Airbag Control
Module.>
Replace the airbag
main harness with
bulkhead harness.

WI-9
Basic Diagnostic Procedure
WIRING SYSTEM
•Each connector number shown in the wiring dia-
gram corresponds to that in the wiring harness. The
location of each connector in the actual vehicle is
determined by reading the first character of the
connector (for example, a “F” for F8, “i” for i16, etc. )
and the type of wiring harness. The first character
of each connector number corresponds to the area
or system of the vehicle.
Symbol Wiring harness and cord
FFront wiring harness
BBulkhead wiring harness
EEngine wiring harness
TTransmission cord
DDoor cord LH & RH, Rear gate cord
Rear door cord LH & RH, Rear defogger cord
iInstrument panel wiring harness
R
Rear wiring harness,
Fuel tank cord,
Roof cord, Rear gate cord,
Rear defogger ground cord (Sedan model)
AB Airbag wiring harness
F23
F98F21
F58
F100F5
F27
F47
F34F19F22
F96
WI-02753
Each connector number shown in wiring diagram corresponds to that in the vehicle.
F19
FRONT TURN SIGNAL LIGHT LH (UPPER)
BG2B1
F22
FRONT TURN SIGNAL LIGHT LH (LOWER)
BG3B2
(GRAY)F3(GRAY)F19
12

WI-149
Harness Components Location
WIRING SYSTEM
54.Harness Components Location
A: LOCATION
(1) Front wiring harness (6) Rear door cord RH (10) Rear door cord LH
(2) Engine wiring harness (7) Rear wiring harness (11) Front door cord LH
(3) Bulkhead wiring harness (8) Roof cord (12) Transmission cord
(4) Instrument panel wiring harness (9) Rear gate cord (13) Rear oxygen sensor cord
(5) Front door cord RH
WI-08150
(8)
(6)(7)
(5)(4)
(3)
(7)
(13)
(12)
(11)
(2)
(1)
(7)
(7)
(9)
(10)

WI-152
Bulkhead Wiring Harness (In Engine Compartment)
WIRING SYSTEM
56.Bulkhead Wiring Harness (In Engine Compartment)
A: LOCATION
Connector Connecting to
No. Pole Color Area No. Description
B3 5 Black B-2 Air flow sensor
B6 2 Gray B-2 Front ABS wheel speed sensor RH
B8 5 Black B-4 Front wiper motor
B10 4 Gray B-4 Pressure switch
B11 20 Gray B-3 T4Tr a n s m i s s i o nB12 8 Brown B-3 T3
B14 1 Black B-3 Starter (Magnet)
B15 2 Gray B-4 Front ABS wheel speed sensor LH
B16 2 Gray B-4 Brake fluid level switch
B20 16 Brown B-3 E1
Engine wiring harnessB21 54 Black B-3 E2
B22 16 Brown B-3 E3
B143 20 B-4
Main fuse box (M/B)B144 9 Brown B-4
B145 7 Brown B-4
B146 6 Gray C-4 Washer motor & washer tank
B186 8 B-4 Main fuse box (M/B)
B310 46 Black B-2 VDC control module
B360 16 Gray C-4 F109Through joint connectorB361 14 Gray B-4 F108
B407 2 Black B-5 Paddle light LH
B409 4 Black B-5Wiper relay unitB410 3 Gray B-5
B411 3 Black B-4 Pressure sensor
B417 2 Gray C-3 Vacuum pump
B422 4 Black B-3 Vacuum pump relay
B423 8 Black B-3 Relay box
B430 2 Black B-2 Paddle light RH
B432 8 Black B-4 SBF holder
B433 2 B-4 Main fuse box (M/B)
: White or natural color
Connector Connecting to
No. Pole Color Area No. Description
AB13 2 Yellow C-3 Front sub sensor LH
AB16 2 Yellow C-1 Front sub sensor RH
Connector Connecting to
No. Pole Color Area No. Description
E3 16 Brown A-3 B22 Bulkhead wiring harness
E24 4 Light gray C-3 Front oxygen (A/F) sensor LH
E25 4 Dark gray B-4 Rear oxygen sensor LH
E47 4 Light gray C-3 Front oxygen (A/F) sensor RH
E61 4 Dark gray C-3 Rear oxygen sensor RH

WI-153
Bulkhead Wiring Harness (In Engine Compartment)
WIRING SYSTEM

WI-154
Bulkhead Wiring Harness (In Compartment)
WIRING SYSTEM
57.Bulkhead Wiring Harness (In Compartment)
A: LOCATION
Connector Connecting to
No. Pole Color Area No. Description
B31 12 Yellow C-1 AB1 Airbag wiring harness
B32 8 C-2Tu r n s i g n a l & h a z a r d
unit
B36 28 Blue B-2 i1Instrument panel wir-
ing harnessB38 20 B-5 i3
B41 2 C-2Powe r w in d ow ci r cu i t
breaker
B47 6 Brown B-5 Main relay
B52 24 B-2 Fuse & relay box (F/B)
B54 24 C-2TCMB55 24 Gray C-3
B65 4 Black B-3Stop light and brake
switch
B68 8 B-3 Roll connector
B69 4 B-3 Parking light switch
B70 18 B-3
Combination switch
(Wiper & washer
switch)
B71 17 B-3
Combination switch
(Front fog light switch)
(Lighting switch)
B72 6 B-3 Ignition switch
B77 7 Green B-4 Mode actuator
B86 5 B-4 Blower fan controller
B87 2 C-5 Blower fan motor
B88 2 B-4Evaporation thermo
switch
B90 12 B-4 R50 Roof cord
B91 7 Green B-4FRESH/RECIRC actu-
ator
B96 8 Black B-2Daytime running light
control module
B97 20 C-1 R1Rear wiring harnessB98 24 Black B-5 R2
B116 12 C-4 AT select lever
B122 8 D-5 Joint connector
B134 34 C-4
ECMB135 35 C-4
B136 35 C-4
B137 31 D-5
B152 10 Gray B-2
Fuse & relay box (F/B)B158 8 B-2
B159 9 Brown B-2
B177 2 B-4 Wiper deicer
B225 40 Black C-2
Seat heater relay
Starter relay
Pow er w i n dow r el ay
Fuse (Relay block)
Blower fan relay
Fr o nt fog li g ht r el ay
Mirror heater relay
Rear fog light relay
Wiper deicer relay
B228 15 B-2 OP connector
B231 4 B-3 Steering angle sensor
B235 7 Green B-4Passenger’s side air
mix actuator
B242 10 B-2Daytime running light
control module
B280 30 C-3Body integrated unitB281 28 C-3
B282 16 C-5Auto A/C control mod-
ule
B283 26 C-5
Auto A/C control mod-
ule (Rear defogger
switch)
B315 6 Black B-4Accelerator pedal
position sensor
B327 6 Brown B-5Rear oxygen sensor
relay
B350 4 B-3Key war ning switch &
key lock solenoid
B351 2 Black B-4 Antenna
B352 8 C-3CAN joint connectorB355 8 B-3
B356 4 Black C-3 Back-up light relay
B357 4 Black C-3 P-VIGN relay
B359 5 Black D-4 Yaw rate sensor
B362 8 Black B-5 Relay holder
B370 2 Black B-4 Diode
B373 2 B-1 Fuse box
B390 7 Green B-4Driver’s side air mix
actuator
B402 16 Black B-2 Data link connector
B403 25 B-2 i2Instrument panel wir-
ing harness
B404 1 Black B-2 Parking brake switch
B405 4 Brown B-2Diode (Daytime run-
ning light & parking)
B413 2 B-3In vehicle tempera-
ture sensor
B414 2 B-4 Key illumination
Connector Connecting to
No. Pole Color Area No. Description

WI-155
Bulkhead Wiring Harness (In Compartment)
WIRING SYSTEM
B416 8 D-4 CAN joint connector
B418 2 B-4Foot light (Passen-
ger’s side)
B419 7 B-4 Blower fan relay
B420 2 Green C-4Te s t m o d e c o n n e c t o rB421 2 Green C-4
B424 8 D-5Joint connectorB426 8 D-5
B431 2 B-3Foot light (Driver’s
side)
: White or natural color
Connector Connecting to
No. Pole Color Area No. Description
Connector Connecting to
No. Pole Color Area No. Description
AB1 12 Yellow C-1 B31Bulkhead wiring har-
ness
AB2 4 Yellow B-4 AB7Inflator (Driver’s seat)
(Roll connector)
AB6 28 Yellow C-3 Airbag control module
AB9 4 Yellow C-3 C-3Inflator (Passenger’s
seat)
AB3
52BlackB-1 Fuse & relay box (F/B)
AB5
52YellowB-5AB5
7Rear wiring harness