lock SUZUKI BALENO 1999 1.G User Guide

60G-74E

STEERING COLUMN CONTROLS

WINDSCREEN WIPER AND

WASHER LEVER

60G-04-007E

Windscreen Wipers

To turn the windscreen wipers on, move the

lever down to one of the three operating

positions. In the "INT position (if equipped),

the wipers operate intermittently. The "INT'

position is very convenient for driving in mist

or light rain. In the "LO" position, the wipers

operate at a steady low speed. In the "HI"

position, the wipers operate at a steady high

speed. To turn off the wipers, move the lever

back to the "OFF position.
60G-04-008E

If the lever is equipped with "INT TIME" control,

turn the control toward the "SLOW" or "FAST'

positions to adjust the intermittent wiper

operation to the desired interval.

60G-04-011E

The operation of windscreen wiper and washer

Type-2 is same as Type-1.
60G-04-009E

Windscreen Washer

To spray windscreen washer fluid, pull the

lever toward you. The windscreen wipers will

automatically turn on at low speed if

they are not already on and the "INT" position

is equipped.

To prevent windscreen icing in cold

weather, turn on the defroster to heat

the windscreen before and during

windscreen washer use.

Do not use radiator antifreeze in the

windscreen washer reservoir. It can

severely impair visibility when

sprayed on the windscreen, and can

also damage your vehicle's paint.

35

4-4

STEERING COLUMN CONTROLS
60G-74E

CAUTION

To help prevent damage to the

windscreen wiper and washer system

components, you should take the

following precautions:

• Do not continue to hold in the lever

when there is no windscreen washer

fluid being sprayed or the washer

motor can be damaged.

• Do not attempt to remove dirt from

a dry windscreen with the wipers or

you can damage the windscreen and

the wiper blades. Always wet the

windscreen with washer fluid before

operating the wipers.

• Clear ice or packed snow from the

wiper blades before using the

wipers.

• Check the washer fluid level

regularly. Check it often when the

weather is bad.

• Only fill the washer fluid reservoir

3/4 full during cold weather to allow

room for expansion if the

temperature falls low enough to

freeze the solution.
HORN
REAR WIPER AND WASHER

(if equipped)

60G-04-010

Press the horn button of the steering wheel to

sound the horn. The horn will sound with the

ignition switch in any position.
Press the button located at the end of the

windscreen wiper and washer lever to operate

the rear washer and turn the lever anti

clockwise to operate the rear washer.

4-5
36

60G-74E
INSTRUMENT PANEL

ASHTRAY

GLOVE BOX

60G-05-010

843-05-011E

Front Ashtray

To remove the front panel ashtray for cleaning,

push down on the metal plate, and pull the

ashtray completely out of its holder.
Rear Ashtray

To remove the rear ashtray, push down on the

tongue and pull the ashtray out of its holder.

Make sure tobacco is fully extinguished

before closing the ashtray. Never throw

waste in the ashtray: it could create a

fire hazard.
60G-05-011

To open the glove box, pull the latch lever.

To close it, push the lid until It latches securely.

If a lock is equipped on the latch lever, lock

the glove box by inserting the key and turning

it clockwise and unlock the glove box by

turning the key counterclockwise.

Never drive with the glove box lid open.

It could cause injury if an accident

occurs.

45

5-8

INSTRUMENT PANEL
60G-74E

HEATING SYSTEM (if equipped)

The heating system provides heating

demisting, and ventilation.

a. Windscreen defroster

b. Side defroster

c. Side outlet

d. Center outlet

e. Floor outlet

60G-05-012

@

RECIRCULATED AIR FRESH AIR

60G-05-013

5-9
46

OTHER CONTROLS AND EQUIPMENTS

60G-74E

FUEL FILLER CAP

60G-06-002

The fuel filler cap is located on the left rear

side of the vehicle. The fuel filler lid can be

unlocked by pulling up the opener lever located

on the outboard side of the driver's seat and

locked by simply closing the lid.

Remove the fuel filler cap slowly. The

fuel may be under pressure and may

spray out, causing injury.
Petrol Is extremely flammable. Do not

smoke when refuelling, and make sure

there are no open flames or sparks in

the area.
60G-06-OO3

The fuel tank filler cap has a "screw-on ratcheting

type" feature.

• To remove - turn the cap counterclockwise.

Turn the cap slowly to allow any residual

pressure to escape.

• To install - turn the cap clockwise and

tighten it securely until a "ratcheting"

(clicking) sound is heard. The "ratcheting"

sound indicates that the cap is on properly.

6-3
56

60G-74E
OTHER CONTROLS AND EQUIPMENT

FOLDING REAR SEATS

70F-04-008E

If you need to replace the fuel cap, use

only a cap specified for your model.

Using an improper fuel cap can cause

a serious malfunction of the fuel

system. You can get the correct

replacement cap from your MARUTI

dealer.
63B-06-013

The rear seat of your vehicle can be folded

forward ro provide additional luggage space.

To lower the seatback, hook the webbing of

both outboard lap-shoulder belts in the belt

hangers, pull up the lock knobs (© and @)

simultaneously and fold forward the seatback.

To raise the seatback, lift it up and push back

until it locks into place.

When you move a seatback, make sure

the belt webbing is hooked in the belt

hangers (if equipped) so the seat belts

are not caught by the seatback, seat

hinge, or seat latch.This helps prevent

damage to the belt system.
63B-06-014

When returning a rear seat to the

normal position, make sure that

movement of the seatback is

unobstructed and the seatback is

securely latched.

57

6-4

OTHER CONTROLS AND EQUIPMENTS

60G-74E

SUN VISOR
INTERIOR LIGHT SWITCH

70F-04-024

Luggage or other cargo should be

stowed in the luggage compartment

with the rear seat in an upright position,

whenever possible. If you need to carry

cargo in the passenger compartment

with the rear seat back folded forward,

be sure to secure the cargo or it may

be thrown about, causing injury. Never

pile cargo higher than the seatbacks.
The sun visors can be pulled down to block

glare coming through the wind screen, or they

can be unhooked and turned to the side to

block glare coming through the side window.

CAUTION

When unhooking and hooking a sun

visor, be sure to handle it by the hard

plastic parts or the sun visor can be

damaged.
60G-06-004

This light switch has three positions which

function as described below:

© The light comes on and stays on

regardless of whether the door is open or

closed.

© The light comes on when the door is

opened.

® The light remains off even when the door

is opened.

NOTE:

Both Front and Rear doors are involved in

lighting operation of the interior light.

6-5
58

60G-74E
OTHER CONTROLS AND EQUIPMENT

ASSIST GRIPS
BONNET

70F-04-015

Assist grips are provided for passenger

convenience.

Do not hang Herns on the assist grips.

They could obstruct the driver's view,

resulting in an accident, or could be

thrown about in an accident or abrupt

manoeuvre, causing injury.
60G-06-005

To open the bonnet:

1) Pull the bonnet release handle located on

the outboard side of the driver's side of

the instrument panel. This will disengage

the bonnet lock halfway.
60G-06-006

2)
Push the under-bonnet release lever

sideways with your finger, as shown in the

illustration. While pushing the lever, lift up

the bonnet.

59
6-6

OTHER CONTROLS AND EQUIPMENTS

60G-74E

CUP HOLDER (if equipped)
TYRE CHANGING TOOLS

60G-06-007

3)
Continue to lift up the bonnet until it is high

enough to support with the prop rod.

Make sure the bonnet Is fully closed

and latched before driving. If it is not,

it can fly up unexpectedly during

driving, obstructing your view and

resulting in an accident.
60G-06-008

To use the cup holder, pull it out fully. After

using the holder, push it back in.

Do not use the cup holder to hold cups

containing hot liquids, or objects other

than cups. Objects in the cup holder

may be thrown about during a sudden

stop or impact, and could cause

personal injury.
60G-06-009

The jack, wheel wrench and jack crank are

stowed in the luggage compartment behind

the rear seat.

To remove the jack, turn its shaft

counterclockwise and pull the jack out of the

storage bracket. To stow the jack, place it in

the storage bracket and turn the shaft

clockwise until the jack is securely held in

place.

6-7
60

60G-74E
OTHER CONTROLS AND EQUIPMENT

LUGGAGE COMPARTMENT TRIM TRUNK (BOOT) LIGHT (if equipped)

Luggage or other cargo placed in the luggage

compartment are hidden from view by a

luggage compartment trim.

Do not carry items on top of the

luggage compartment trim, even if they

are small and light. Objects on top of

the trim could be thrown about In an

accident, causing injury, or could

obstruct the driver's rear view.

60G-06-010
6OG-O6-O11

The jack should be used only to change

wheels. It is important to read the

jacking Instructions in the

EMERGENCY SERVICE section of this

manual before attempting to use the

jack.
When you open the trunk (boot) lid, the trunk

(boot) light comes on and remains on as

long as you keep the lid open.

Do not leave the boot (trunk) lid open

for a long time, or the battery will

discharge.

After using the jack, jack crank and

wheel wrench, be sure to stow them

securely or they can cause injury if an

accident occurs.

61

6-8

OTHER CONTROLS AND EQUIPMENTS
60G-74E

FRONT SEAT BACK POCKET

(if equipped)
REAR SPOILER WITH STOP LAMP

Other Controls (if equipped)

63B-06-022

This pocket is provided for holding light and

soft things such as gloves, newspapers or

magazines.

Do not put hard or breakable objects

In the pocket. If an accident occurs,

objects such as bottles, cans etc. can

injure the occupants in the rear seat.
60G-50-002E

Rear Spoiler is provided to improve

aerodynamic stability at higher speeds and

better asthetics. Stop Lamp (if equipped) is

fitted inside the Rear Spoiler. The stop lamp

will glow as and when the Brake Pedal is

depressed.

CAUTION

Never close the dicky door too hard or

with jerk or lift the dicky by holding

spoiler, rear spoiler may get damaged.

Close the dicky door gently and make

sure it is closed properly.
ALLOY WHEELS

Maintenance with tyre wears (if equipped)

60G-50-003E

Wider alloy wheels are provided in the vehicle

for better grip on the road and more fuel

economy. For balancing of wheels please

consult MARUTI authorised workshop.

CAUTION

Never try to remove the tyre from alloy

wheel rim in convention manner (by

hammering), it will damage the wheel

rim. Always insist on tyre changing

machine.

6-9
62

60G-74E

OTHER CONTROLS AND EQUIPMENT

POWER ANTENNA Other Controls

(if equipped)
LEATHER COVER

Steering Column Controls (if equipped)

60G-50-004E

60G-50-006E

Power antenna on the rear side will

automatically come up on switching on the

AM/FM receiver fitted in the vehicle.
For better control on steering wheel leather

cover is provided.
HIGH MOUNT STOP LAMP

(if equipped)

High mount stop lamp is provided with your

vehicle and is fitted on rear parcel tray. The

stop lamp will glow as when the brake pedal

will be depressed.

To change the bulb of the stop lamp, remove

the clips at both sides of the cover, by

pressing the inner pin inside so that the clip

gets loose and remove the bulb on turning

it anticlock-wise

The rating of bulb is 21W/12V.There are one

bulb in high mount stop lamp.

63

6-10

60G-74E
OPERATING YOUR VEHICLE

Once a week, or each time you fill your fuel

tank, perform the following under-bonnet

checks:

1) Engine oil level.

2) Coolant level.

3) Brake fluid level.

4) Power steering (if equipped) fluid level.

5) Windscreen washer fluid level.

6) Battery solution level.

7) Bonnet latch operation.

Pull the bonnet release handle inside the

vehicle. Make sure that you can not open

the hood all the way without releasing the

secondary latch. Be sure to close the hood

securely after checking for proper

operation. See "All Latches, Hinges &

Locks" of "PERIODIC MAINTENANCE

SCHEDULE" in the "INSPECTION AND

MAINTENANCE" section for lubrication

schedule.

Make sure the bonnet is fully closed

and latched before driving. If it is not,

it can fly up unexpectedly during

driving, obstructing your view and

resulting in an accident.
STARTING THE ENGINE

Before starting the engine:

1) Make sure the parking brake is applied

fully.

2) Manual Transmission - Shift into "N"

(neutral) and depress the clutch pedal all

the way to the floor. Hold it while starting

the engine.

Make sure that the parking brake is

applied fully and the transmission is in

Neutral before attempting to start the

engine.

CAUTION

Stop turning the starter immediately

after the engine has started or the

starter system can be damaged.

Do not crank the engine for more

than 15 seconds at a time. If the

engine doesn't start on the first try,

wait about 15 seconds before trying

again.
Starting a Cold Engine

Engine which is started after 6 hours should

be treated as cold engine.

For Electronic fuel injection models

• With your foot off the accelerator pedal,

crank the engine by turning the ignition

key to "START1. Release the key when the

engine starts.

• If the engine does not start after 15

seconds of cranking, wait about 15

seconds, then press down the accelerator

pedal to 1/3 of its travel and try cranking

the engine again. Release the key and

accelerator pedal when the engine starts.

• If the engine still does not start, try holding

the accelerator pedal all the way to the

floor while cranking. This should clear the

engine if it is flooded.

Starting a Warm Engine

For Electronic fuel injection models:

Use the same procedure as for "Starting a cold

Engine".

67

7-2

OPERATING YOUR VECHILE

60G-74E

USING THE TRANSMISSION

70F-04-005E

Starting off

To start off, depress and maintain pressure

upon the clutch pedal and change into 1st

gear. After releasing the parking brake,

gradually release the clutch. When you hear

a change in the engine's sound (speed), gently

apply pressure to the accelerator to keep the

engine sound (speed) constant whilst

continuing to gradually release the clutch.
Gear changing

All forward gears are synchronized, which

provides for quiet, easy changing. Always

depress the clutch pedal fully before changing

gears.The following table shows the maximum

allowable speed for each gear.
GEAR

First

Second

Third

Fourth

Fifth
MAXIMUM SPEED

50 km/h

95 km/h

140 km/h

Top Speed

Top Speed

7-3
68

60G-74E
OPERATING YOUR VEHICLE

CATALYTIC CONVERTER

(if equipped)

70F-05-005

The purpose of the catalytic converter installed

on your vehicle is to convert exhaust pollutants

to harmless water vapour, carbon dioxide, and

nitrogen. Use of leaded fuel in vehicles

equipped with catalytic converters is

prohibited, because lead deactivates the

pollutant-reducing components of the catalyst

system.

It is very important to keep the engine properly

tuned. Engine misfiring, which can result from

an improperly tuned engine, may cause

overheating of the catalyst. This may result in

permanent heat damage to the catalyst and

other vehicle components.
CAUTION

To minimize the possibility of catalyst

or other vehicle damage:

• Maintain the engine in the proper

operating condition.

• In the event of an engine

malfunction, particularly one

involving engine misfire or other

apparent loss of performance, have

the vehicle serviced promptly.

• Do not turn off the engine or

interrupt the ignition when the

transmission is in gear and the

vehicle is in motion.

• Do not try to start the engine by

pushing or towing the vehicle, or

coasting down a hill.

• Do not idle the engine with any spark

plug wires disconnected or

removed, such as during diagnostic

testing.

• Do not idle the vehicle for prolonged

periods if idling seems rough or

there are other malfunctions.

• Do not allow the fuel tank to get near

the empty level.
60Q-07-002E

Be careful where you park and drive;

the catalytic converter and other

exhaust components can get very hot.

As with any vehicle, do not park or

operate this vehicle in areas where

combustible materials such as dry

grass or leaves can come in contact

with a hot exhaust system.

7-6

OPERATING YOUR VECHILE

60G-74E

IMPROVING FUEL ECONOMY

The following instructions will help you improve

fuel economy.

Avoid excessive idling:

If you are to wait for more than a minute while

you are parked, stop the engine and start it

again later. When warming up a cold engine,

allow the engine to idle until the temperature

gauge pointer comes up to the "C" position. In

this position, the engine is sufficiently warm

for starting off.

Avoid "fast" starts:

Fast starts away from lights or stop signs will

consume fuel unnecessarily and shorten

engine life. Start off slowly.

Avoid unnecessary stops:

Avoid unnecessary deceleration and stopping.

Try to maintain a slow, steady speed whenever

possible. Slowing down and then accelerating

again uses more fuel.

Keep a steady cruising speed:

Keep as constant a speed as road and traffic

conditions will permit.
Air Outlet side

(Facing up)

60G-09-010

Keep the air cleaner clean:

A dirty air cleaner will cause the carburation

system to supply too much fuel to the engine

for the amount of air being supplied. The result

is waste of fuel due to incomplete combustion.

Keep weight to a minimum:

The heavier the load, the more fuel the vehicle

consumes. Take out any luggage or cargo

when it is not necessary.

Keep tyre pressures correct:

Under-inflation of the tyres can waste fuel due

to increased running resistance of the tyres.

Keep your tyres inflated to the correct pressure

shown on the label on the driver's side door

or door lock pillar.
TRAILER TOWING

Your MARUTI was originally designed to carry

people and a normal amount of cargo, not to

tow a trailer. Maruti does not recommend you

use your vehicle to tow a trailer.Towing a trailer

can adversely affect handling, durability, and

fuel economy.

7-7

72
71

60G-74E
INSPECTION AND MAINTENANCE

Interval: This interval should be Judged

by odometer reading or months,

whichever comes first.
km (x 1,000)

months

FUEL

1. Air cleaner Paved-road

Dusty condition

2. Accelerator cable and Throttle shafts

3. Fuel tank cap, fuel lines & connections(leakage,damage)

4. Fuel filter (leakage)

CLUTCH AND TRANSMISSION

1. Clutch pedal (play)

2. Clutch slipping (dragging or excessive damage)

3. Manual Transmission/Transfer and Differential oil (level, leakage)

DRIVE SHAFTS

1. Drive shafts boots (bent of boots damage)

BRAKE

1. Brake fluid (level, leakage)

2. Brake pedal (pedal-to-wall clearance)

3. Parking brake lever and cable (play, damage)

4. a. Brake discs and pads, (wear)

b. Brake drums & shoes

5. Master cylinder and wheel cylinder or calliper (oil leakage.boot kit)

6. Brake hoses and pipes (leakage, damage)
FREE

1

1
INSPECTIONS

5

6
10

12

Clean every 5,000 km. F
PERIODIC MAINTENANCE

20

24
30

36
40

48

Replace every 40,000 krr
50

60
SERVICE

60

72
AT

70

84
COST

80

96

Clean every 2,500 km or as required. Replace every 40,000 km. More frequent

replacement if dust condition is severe.

-

-

I

I

I

I

-

I

I

I

-

-

I

I
I&L

I

I

I

I

I

I

I

I

I

I

-

I

I
I&L

-

I

I

I

I

I

I

I

I

I

I

I

I
I&L

-

I

I

I

R

I

R

I

I

I

I

I

I
I&L

-

I

I

I

I

I

I

I

I

I

I

I

I
I&L

I

R

I

I

R

I

R

I

I

I

I

R

I
I&L

-

I

I

I

I

I

I

I

I

I

I

I

I
I&L

-

I

I

I

R

I

R

I

I

I

I

I

I
I&L

-

I

I

I

I

I

I

I

I

I

I

I

I
I&L

I

R

I

I

R

I

R

I

I

I

I

R

I

87

9-4

INSPECTION AND MAINTENANCE

60G-74E

Interval: This Interval should be judged

by odometer reading or months,

whichever comes first
km (x 1,000)

months

WHEEL

1. Tyres (air pressure, abnormal wear, crack, ROTATION)

2. Wheels (damage)

3. Front wheel bearings (loose, damage)

4. Rear wheel bearings (loose, damage)

FRONT AND REAR SUSPENSION

1. Suspension strut (oil leakage, damage)

2. Suspension arms and knuckle supports (loose.damage)

3. Rear spring (damage)

4. Shock absorbers (oil leakage, damage)

5. All bolts and nuts (loose)

6. Suspension arms and Tension rods

STEERING

1. Steering wheel (play, loose)

2. Power steering fluid (level, leakage)/connections

3. All rods and arms (loose, damage, wear)

ELECTRICAL

1. Battery electrolyte (level, leakage)

2. Wiring harness connection (looseness, damage)

3. Lighting system (operation, stains, damage)

4. Horn (operation)

5. System voltage

BODY

1. All chassis bolts and nuts (tighten)

2. All Latches, Hinges & Locks (function)
FREE

1

1
INSPECTIONS

5

6

Rotate and

I

-

-

I

-

-

I

-

-

I

I

I

I

-

I

I

-

-

I
I

I

I

I

I

I

I

T

I

I

I

I

I

I

I

I

I

I

I&L
10

12
PERIODIC

20

24

inspect every 5,000

I

I

I

I

I

I

I

T

I

I

I

I

I

I

I

I

I

T

I&L
I

I

I

I

I

I

I

T

I

I

I

I

I

I

I

I

I

T

I&L
30

36

km

I

I

I

I

I

I

I

T

I

I

I

I

I

I

I

I

I

T

I&L
MAINTENANCE

40

48

I

I

I

I

I

I

I

T

I

I

I

I

I

I

I

I

I

T

I&L
50

60

I

I

I

I

I

I

I

T

I

I

I

I

I

I

I

I

I

T

I&L
SERVICE

60

72

I

I

I

I

I

I

I

T

I

I

I

I

I

I

I

I

I

T

I&L
AT

70

84

I

I

I

I

I

I

I

T

I

I

I

I

I

I

I

I

I

T

I&L
COST

80

96

I

I

I

I

I

I

I

T

I

I

I

I

I

I

I

I

I

T

I&L

9-5
88

60G-74E
INSPECTION AND MAINTENANCE

60G-09-002E

Oil Level Cheek

It is important to keep the engine oil at the

correct level for proper lubrication of your

vehicle's engine. Check the oil level with the

vehicle on a level surface. The oil level

indication may be inaccurate if the vehicle is

on a slope. The oil level should be checked

either before starting the engine or at least 5

minutes after stopping the engine.

Pull out the oil dipstick, wipe oil off with a clean

cloth, insert the dipstick all the way into the

engine, then remove it again. The oil on the

stick should be between the upper and lower

limits shown on the stick. If the oil level

indication is near the lower limit, add enough

oil to raise the level to the upper limit.

91
60G-09-003E

Refilling

Remove the oil filler cap and pour oil slowly

through the filler hole to bring the oil level to the

upper limit on the dipstick. Be careful not to

overfill. Too much oil is almost as bad as too

little oil. After refilling, start the engine and allow

it to idle for about a minute. Stop the engine,

wait for five minutes and check the oil level again.

Changing Engine Oil and Fitter

Drain the engine oil while the engine is still

warm.

1) Remove the oil filler cap.

2) Place a drain pan under the drain plug.

3) Using the correct spanner remove the

drain plug and drain out the engine oil.
60G-09-004

The engine oil temperature may be high

enough to burn your fingers when the

drain plug Is loosened. Watt until the

drain plug is cool enough to touch with

your bare hands.

9-8

INSPECTION AND MAINTENANCE
60G-74E

New and used oil can be hazardous.

Children and pets may be harmed by

swallowing new or used oil. Keep new

and used oil and used oil fitters away

from children and pets.

Continuous contact with used engine

oil has been found to cause (skin)

cancer in laboratory animals. Brief

contact with used oil may irritate skin.

To minimize your exposure to used oil,

wear a long-sleeve shirt and

moistureproof gloves (such 'as

dishwashing gloves) when changing

oil. If oil contacts your skin, wash

thoroughly with soap and water.

Launder any clothing or rags if wet with

oil.

Recycle or properly dispose of used oil

and filters.

4) Reinstall the drain plug and gasket.

Tighten the plug to a torque of

5.0 kg-m (36.5 Ib-ft).
70F-07-010

Replace the oil filter

1) Using an oil filter wrench, turn the oil filter

counterclockwise and remove it.

2) Using a clean rag, wipe off the mounting

surface on the engine where the new filter

will be seated.

3) Smear a little engine oil around the rubber

gasket of the new oil filter.

4) Screw on the new filter by hand until the

filter gasket contacts the mounting

surface.
60G-09-005

CAUTION

To tighten the oil filter properly, it is

important to accurately identify the

position at which the filter gasket first

contacts the mounting surface.

5) Tighten the filter 3/4 turn from the point of

contact with the mounting surface, [or to

1.4 kg-m (10.5 Ib-ft)] using an oil filter

wrench.

9-9
92