lock SUZUKI BALENO 1999 1.G Owner's Manual

60G-74E
INSPECTION AND MAINTENANCE

CAUTION

When adding or replacing coolant,

use a high quality ethylene glycol

antifreeze and anticorrosion (Non-

Amine type) diluted with distilled

water. If the lowest ambient

temperature in your area is expected

to be -15°C (5°F) or above, make the

antifreeze concentration of the

mixture you use at least 30% but no

more than 50%. If -16°C (3°F) or

below, make the concentration at

least 50%. If the 50% concentration

does not provide adequate

protection against freezing, follow

the instructions on the antifreeze

container to obtain the desired

freezing point.

When putting the cap on the

reservoir tank, line up the arrow on

the cap and the arrow on the tank,

or coolant can leak out.
70F-07-019E

Coolant Replacement

1) When the engine is cool, remove the

radiator cap by turning it slowly to the left

until a "stop" is felt. Do not press down

while turning the cap. Wait until any

pressure is released, then press down on

the cap and continue turning it

anticlockwise.
60G-09-039E

It is dangerous to remove the radiator

cap when the water temperature is

high, because scalding fluid and steam

may be blown out under pressure. Watt

until the coolant temperature has

lowered before removing the cap.

2) Remove the reservoir tank cap. Remove

the reservoir by lifting it up, and drain the

reservoir completely by pouring the

coolant in to a suitable container.

95
9-12

INSPECTION AND MAINTENANCE

60G-74E

WINDSCREEN WASHER FLUID

AIR CLEANER

60G-09-008

3) Loosen the drain plug attached to the

lower part of the radiator and drain the

coolant into a suitable container.

4) Tighten the drain plug on the radiator, fill

the radiator with coolant and install the

radiator cap.

5) Refit the reservoir and fill it with the correct

coolant to the "FULL" line. Refit the

reservoir tank cap, ensuring the arrows are

correctly aligned.

CAUTION

The coolant must be replaced with the

vehicle on level ground.
63B-09-001

Check that there is washer fluid in the tank.

Refill it if necessary. Use a good quality

windscreen washer fluid, diluted with water as

necessary.

Do not use "antifreeze" solution in the

windscreen washer reservoir.This can

severely impair visibility when sprayed

on the windscreen, and can also

damage your vehicle's paint.

CAUTION

Damage may result if the washer motor

is operated whilst the fluid or fluid

nozzles are frozen or with no fluid in

the washer tank.
6OG-09-009

If the air cleaner is clogged with dust, there

will be greater intake resistance, resulting in

decreased power output and increased fuel

consumption.

Take out the air cleaner element after

unhooking the clamps shown in the illustration.

Blow off dust on air cleaner element by

compressed air. If the air cleaner element

appears to be dirty, replace it with a new one.

9-13
96

60G-74E
INSPECTION AND MAINTENANCE

70F-07-029
Do not use any fluid other than SAE

J1703 or DOT-3 brake fluid. Do not

use reclaimed fluid or fluid that has

been stored in old or open

containers. It is essential that foreign

particles and other liquids are kept

out of the brake fluid reservoir.

CAUTION

The brake fluid should be replaced

every two years or 20,000 km.

panel will come on (the engine must

be running with the parking brake

fully disengaged). Should the light

come on, immediately ask your

MARUTI dealer to inspect the brake

system.

A rapid fluid loss Indicates a leak in

the brake system which should be

inspected by your MARUTI dealer

immediately.

Brake fluid can harm your eyes and

damage painted surfaces. Use

caution when refilling the reservoir.
NOTE:

With disc brakes, the fluid level can be

expected to gradually fall as the brake pads

wear.

99
70F-07-030

Brake Pedal

Check if the brake pedal stops at the regular

height without "spongy" feeling when you

depress it. If not, have the brake system

inspected by your MARUTI dealer. If you doubt

the brake pedal for the regular height, check

it as follows:

With the engine running, measure the distance

between the brake pedal and floor wall when

the pedal is depressed with approximately 30

kg (66 lbs) of force. The minimum distance

required is 80 mm (3.1 in). Since your vehicle's

brake system is self-adjusting, there is no need

for pedal adjustment. If the pedal to floor wall

distance as measured above is less than the

minimum distance required, have your vehicle

inspected by your MARUTI dealer.

9-16

INSPECTION AND MAINTENANCE

60G-74E

STEERING

60G-09-015E

NOTE:

When measuring the distance between the

brake pedal and floor wall, be sure not to

include any floor covering in the measurement.

If you experience any of the following

problems with your vehicle's brake

system, have the vehicle inspected

immediately by your MARUTI dealer.

Poor braking performance

Uneven braking (Brakes not working

uniformly on all wheels.)

Excessive pedal travel

Brake dragging

Excessive noise

Pedal pulsation (Pedal pulsates

when depressed.)
63B-09-00SE

Parking brake

Check the parking brake for proper adjustment

by counting the number of clicks made by the

ratchet teeth as you slowly pull up on the

parking brake lever to the point of full

engagement. The parking brake lever should

stop between the 3rd and 5th ratchet tooth

and the rear wheels should be securely locked.

If the parking brake is not properly adjusted

or the brakes drag after the lever has been

fully released, have the parking brake

inspected and/or adjusted by your MARUTI

dealer.
60G-09-016

Check the play of the steering wheel by gently

turning it from left to right and measuring the

distance that it moves before you feel slight

resistance. The play should be between 0 -

30
mm
(0.0 -1.2 in).

Check that the steering wheel turns easily and

smoothly without rattling by turning it all the

way to the right and to the left while driving

very slowly in an open area. If the amount of

free play is outside the specification or you

find anything else to be wrong, an inspection

must be performed by your MARUTI dealer.

9-17

100

60G-74E
INSPECTION AND MAINTENANCE

60G-09-031

Headlights

Open the bonnet. Disconnect the coupler.Turn

the lock ring counterclockwise and remove it.

Remove the sealing rubber.

NOTE:

Your vehicle is provided with two spare

headlight bulbs for replacement in

emegency.
60G-09-037

Push the retaining spring forward and unhook

it. Then remove the bulb. Install a new bulb in

the reverse order of removal.

NOTE:

Your vehicle is provided with two spare

headlight bulbs for replacement in emergency

situations.
70F-07-0S0E

Front Clearance/Turn Signal Light, Side

Turn Signal Light, rear Combination

Light, Registration Plate Light.

To remove a bulb holder from a light housing,

turn the holder counterclockwise and pull it

out. To install the holder, push the holder in

and turn it clockwise.

Two types (small oval and round) of bulb are

used for these lights. To remove and install a

small oval bulb, simply pull out or push in the

bulb.

109

9-26

INSPECTION AND MAINTENANCE

60G-74E

70F-07-051E

To remove a round bulb from a bulb holder,

push in the bulb and turn it counterclockwise.

To install a new bulb, push it in and turn it

clockwise. You can access the individual bulb

holders as described above:
60G-09-032

Front clearance light (A)

Open the bonnet.

Front turn signal light (B)

Trust this replacement job to your authorized

MARUTI dealer as the front bumper and the

headlight housing must be removed for this

job.
70F-07-054

Side turn signal light

Remove the lens by using a plain screw driver

covered with a soft cloth.

9-27
110

60G-74E
INSPECTION AND MAINTENANCE

60G-09-033

60G-09-034

60G-09-035

Rear combination light (tail, stop, turn Registration plate tight Trunk (boot) light (if equipped)

signal, etc.) Undo the two screws and remove the light Turn the lens counterclockwise and pull it off.

Undo the screws that secure the housing and housing.

remove the housing by sliding in the direction

of the white arrow in the illustration.

111

9-28

INSPECTION AND MAINTENANCE

60G-74E

WIPER BLADES

60G-09-036

High mount stop light

Trust this replacement job to your authorized

MARUTI dealer.
70F-07-059

If the wiper blades become brittle or damaged,

or make streaks when wiping, replace the

wiper blades.

To install new wiper blades, follow the

procedure below.

CAUTION

To avoid scratching or breaking the

window, do not let the wiper arm strike

the windshield while replacing the

wiper blade.
NOTE:

Some wiper blades may be different from the

ones described here depending on vehicle

specifications. If so consult your MARUTI

dealer for proper replacement method.

The left and the right wiper arm

assemblies are different from each

other. In case you have to remove the

wiper arm assemblies for any reason,

remember not to interchange the two

while fitting them back. Wrong fitment

may lead to windshield breakage.

9-29
112

60G-74E
INSPECTION AND MAINTENANCE

70F-07-060

For windshield wipers:

1. Hold the wiper arm away from the

window.
72F-09-008

2. Squeeze lock lever (A) towards wiper arms

(B) and remove the wiper frame from the

arm as shown.

113

9-30

60G-74E
EMERGENCY SERVICE

EMERGENCY SERVICE

Jacking Instructions 10-1

Jump Starting Instructions 10-2

Towing 10-4

Emergency Remedies 10-4

Warning Triangle 10-5

115

60G-74E
INSPECTION AND MAINTENANCE

70F-07-060

For windshield wipers:

1. Hold the wiper arm away from the

window.
72F-09-008

2. Squeeze lock lever (A) towards wiper arms

(B) and remove the wiper frame from the

arm as shown.

113

9-30

60G-74E
EMERGENCY SERVICE

EMERGENCY SERVICE

Jacking Instructions 10-1

Jump Starting Instructions 10-2

Towing 10-4

Emergency Remedies 10-4

Warning Triangle 10-5

115

EMERGENCY SERVICE

60G-74E

JACKING INSTRUCTIONS

60G-06-009

1) Park the vehicle securely on hard level

ground.

2) Apply the parking brake firmly and shift into

"R" (Reverse). Choke the front and rear wheel

diagonally opposite the wheel to be changed.

3) Switch on the hazard warning flasher if your

vehicle is in or near traffic.

4) Slacken but do not remove wheel nuts on the

wheel to be changed.

5) Position the jack vertically and raise the jack

by turning the jack handle clockwise until the

jack head recess fits the frame boss.

6) Continue to raise the jack slowly and smoothly

until the tyre clears the ground. Do not raise

the vehicle more than necessary.

10-1
63B-10-001E

70F-08-001

60G-10-001

NOTE:

Use the wheel nut wrench in combination with

jack crank to raise or lower the jack as shown

in the illustration.
Use the jack only to change wheels.

Never jack up the vehicle on an

inclined surface.

Never raise the vehicle with the jack in

a location other than under the frame

boss near the wheel to be changed.

Make sure that the jack is raised at

least 2 inches (51 mm) before it

contacts the vehicle. Use of the jack

when it is within 2 inches of being

fully collapsed may result in failure

of the jack.

Never get under the vehicle when it

is supported by the jack. t=>

116

60G-74E
EMERGENCY SERVICE

JUMP STARTING INSTRUCTIONS

60G-10-002
60G-10-003

Never run the engine when the

vehicle is supported by the jack and

never allow passengers to remain in

the vehicle.
Never attempt to jump start your

vehicle if the battery appears to be

frozen. Batteries in this condition

may explode or rupture if jump

starting is attempted.

When making jump lead

connections, be certain that your

hands and the Jump leads remain

clear from pulleys, belts, or fans.

Batteries produce flammable

hydrogen gas. Keep flames and

sparks away from the battery or an

explosion may occur. Never smoke

when working in the vicinity of the

battery.

If the booster battery you use for

jump starting is installed in another

vehicle, make sure the two vehicles

are not touching each other.

If your battery discharges

repeatedly, for no apparent reason,

have your vehicle inspected by an

authorized MARUTI dealer.

To avoid harm to yourself or damage

to your vehicle or battery, follow the

jump starting instructions below

precisely and in order. If you are in

doubt, call for qualified road service.

10-2

EMERGENCY SERVICE

60G-74E

CAUTION

Vehicle equipped with electronic fuel

injection system will not start by

pushing or towing as the fuel pump

will not work in this condition. This

starting method could also result in

permanent damage to the catalytic

converter. Use jump leads to start a

vehicle with a weak or flat battery.

60G-10-004E

When jump starting your vehicle, use the

following procedure:

1) Use only a 12 volt battery to jump start

your vehicle. Position the good 12V battery

close to your vehicle so that the jump leads

will reach both batteries. When using a

battery installed on another vehicle, DO

NOT LET THE VEHICLES TOUCH. Apply

the parking brakes fully on both vehicles.

2) Turn off all vehicle accessories, except

those necessary for safety reasons (for

example, headlights or hazard lights).
3) Make jump lead connections as follows:

a) Connect one end of the first jump lead

to the positive (+) terminal of the flat

battery.

b) Connect the other end to the positive

(+) terminal of the booster battery.

c) Connect one end of the second jump

lead to the negative (-) terminal of the

booster battery.

d) Make the final connection to an

unpainted, heavy metal part of the

engine of the vehicle with the flat

battery.

Never connect the jump lead directly

to the negative (-) terminal of the

discharged battery, or an explosion

may occur.

10-3
4) If the booster battery you are using is fitted

to another vehicle, start the engine of the

vehicle with the booster battery. Run the

engine at moderate speed.

5) Start the engine of the vehicle with the flat

battery.

6) Remove the jump leads in the exact

reverse order in which you connected

them.

118

60G-74E
EMERGENCY SERVICE

TOWING

If you need to have your vehicle towed, contact

a professional service.

CAUTION

To help avoid damage to your vehicle

during towing, proper equipment and

towing procedures must be used.

Manual Transmission

Whenever possible, your vehicle should be

towed from the front with the front wheels lifted.

If the steering and drivetrain are in good

condition, your vehicle may be towed from the

rear with the rear wheels lifted and the front

wheels on the ground. Before towing, make

sure the steering is unlocked and the

transmission is in neutral.
EMERGENCY REMEDIES

If the Starter Does Not Operate:

1) Try turning the ignition switch to the

"START" position with the headlights

turned on to determine the battery

condition. If the headlights go excessively

dim or go off, it usually means that either

the battery is flat or the battery terminal

contact is poor. Recharge the battery or

correct battery terminal contact as

necessary.

2) If the headlights remain bright, check the

fuses. If the reason for failure of the starter

is not obvious, there may be a major

electrical problem. Have the vehicle

inspected by your authorized MARUTI

dealer.

If the Engine is Flooded

If the engine is flooded with petrol, it may be

hard to start. If this happens, press the

accelerator pedal all the way to the floor and

hold it there while cranking the engine. (Do

not operate the starter motor for more than

15 seconds). Release the accelerator as soon

as the engine has started.
If the Engine Overheats

The engine could overheat temporarily under

severe driving conditions. If the engine coolant

temperature gauge indicates overheating

during driving:

1) Turn off the air conditioner, if equipped.

2) Take the vehicle to a safe place and park.

3) Let the engine run at normal idle speed

for a few minutes until the indicator is within

the normal, acceptable temperature range

between "H" and "C".

If you see or hear escaping steam, stop

the vehicle in a safe place and

Immediately turn off the engine to let it

cool. Do not open the bonnet when

steam is present. When the steam can

no longer be seen or heard, open the

hood to see if the coolant is still boiling.

If it is, you must wait until it stops

boiling before you proceed.

119

10-4

EMERGENCY SERVICE

60G-74E

WARNING TRIANGLE (TYPE-1)

If the temperature indication does not come

down to within the normal, acceptable range:

1) Turn off the engine and check that the

water pump belt and pulleys are not

damaged or slipping. If any abnormality is

found, correct it.

2) Check the coolant level in the reservoir. If

it is found to be lower than the "LOW" line,

look for leaks at the radiator, water pump,

and radiator and heater hoses. If you

locate any leaks that may have caused the

overheating, do not run the engine until

these problems have been corrected.

3) If you do not find a leak, carefully add

coolant to the reservoir and then the

radiator, if necessary. (Refer to "ENGINE

COOLANr in the "INSPECTION AND

MAINTENANCE" section.)
K is dangerous to remove the radiator

cap when the water temperature is

high, because scalding fluid and steam

may be blown out under pressure. The

cap should only be taken off when the

coolant temperature has lowered.

To help prevent personal Injury, keep

hands, tools and clothing away from the

engine cooling fan and airconditioner

fan (if equipped). These electric fans

can automatically turn on without

warning.
843-10-004

In case of vehicle break-down or during

emergency stopping where your vehicle could

become a potential traffic hazard, please keep

the warning triangle, provided with your

vehicle, on the pathway (road) behind the

vehicle so as to warn the approaching traffic,

at an approximate distance of 5-15 m, such

that reflecting side of the triangle faces the

rear. Please activate the hazard warning lamps

before alighting the vehicle to keep the warning

triangle.

10-5
120

60G-74E
EMERGENCY SERVICE

WARNING TRIANGLE (TYPE-2)

In case of vehicle breakdown or during

emergency stopping where your vehicle

could become a potential traffic hazard,

keep the warning triangle, provided with

your vehicle, on the road free from any

obstacles behind your vehicle so as to warn

the approaching traffic, at an approximate

distance of 50-100 m, the reflecting side of

the triangle should face the on coming

traffic. Please activate the hazard warning

lamps before alighting the vehicle to keep

the warning triangle.
Remove the warning triangle

carefully from the box as shown by arrow

1.

Open both the reflector arms as shown

by arrows and lock arms with each other

with the clip provided in the right arm.

Open the bottom stand in counter clock-

wise direction as shown by arrow 3.

Position the warning triangle behind the

vehicle on a plain surface.

Reverse the removal procedure

keeping inside the box.
for

121

10-6

60G-74E
GENERAL INFORMATION

GENERAL INFORMATION

Vehicle Identification 12-1

127

GENERAL INFORMATION

60G-74E

VEHICLE IDENTIFICATION

70F-10-001

Chassis Serial Number

The chassis and/or engine serial numbers are

used to register the vehicle.They are also used

to assist your dealer when ordering or referring

to special service information. Whenever you

have occasion to consult your MARUTI dealer,

remember to identify your vehicle with this

number. Should you find the number difficult

to read, you will also find it on the identification

plate.
70F-10-002

Engine Serial Number

The engine serial number is stamped on the

cylinder block as shown in the illustration and

also on the identification plate.

12-1
128