front SUZUKI GRAND VITARA 1999 2.G Service Workshop Manual

YH4
GRAND
VITARA
7E-12 DIFFERENTIAL (FRONT)
1. Pump assembly
Air Pump Assembly
Removal / Installation
1) Disconnect air hoses and coupler from air pump assembly.
2) Remove pump assembly by removing bolts.
3) Reverse removal procedure for installation.
Tightening Torque
(a): 13 N
.m (1.3 kg-m, 9.5 lb-ft)
Inspection
1) Install special tool, voltmeter and battery to pump assembly as
shown in figure.
2) Tighten adjusting screw of special tool as far as it stops and
close its air check side opening by using fuel hose as blind plug.
Special Tool
(A): 09918-18110
3) Check that motor starts to run (a sound can be heard) when bat-
tery is connected and it stops when specified pressure is ob-
tained.
Check also for air leakage.
Specified pressure: 30.0 ± 45.0 kPa
(0.30 ± 0.45 kg / cm
2, 4.25 ± 6.40 psi)
4) Check that value indicated on voltmeter is within specification
shown below.
When motor is running: 0 ± 1 V
When motor has stopped running: 10 ± 14 V
CAUTION:
Do not run motor more than 10 seconds continuously to
prevent motor breakage.

YH4
GRAND
VITARA
DIFFERENTIAL (FRONT) 7E-13
1. Mounting bracket bolt
2. Mounting bracket R
3. Differential housing
4. Mounting front bolt
1. Differential housing
2. Mounting front bolt3. Mounting bracket L
4. Mounting bracket bolt
1. Mounting bracket
1. Mounting bracket L
2. Bush3. Mounting bracket R
A: Slit alignment 45
4
2
3
1
2
REMOVAL AND INSTALLATION
Differential Mountings
1) Lift up vehicle and turn steering wheel all way to the right.
2) Separate mounting bracket R from differential housing by re-
moving bolts from its lower part.
3) Remove mounting bracket R by removing mounting front bolt
from its upper part.
4) Remove mounting bracket L by removing upper and lower fas-
tening bolts.
5) Check conditions of each bush. If it is damaged or deteriorated,
drive it out with special tools and press for replacement.
Special Tool
(A): 09951-26010
(B): 09951-16080
6) Position slit in each bush as shown when press-fitting it.

YH4
GRAND
VITARA
7E-14 DIFFERENTIAL (FRONT)
1. Mounting bracket R
2. Mounting bracket L
1. Bolt and nut
2. Differential carrier
3. Cross member
4. Bolt
5. Differential rear mounting assembly
7) Position each bush to bracket as shown.
Length ªaº: 3.0 mm (0.12 in.)
8) Use following torque for reinstallation.
Tightening Torque
(a): 85 N
.m (8.5 kg-m, 61.5 lb-ft)
(b): 50 N
.m (5.0 kg-m, 36.5 lb-ft)
REAR MOUNTING
(For front differential carrier)
1) Lift up vehicle and remove mounting assembly by removing 2
bolts and nuts from differential carrier side and 2 bolts from cross
member side.
2) Check mounting rubber for damage or deterioration and replace
as necessary.
3) Use following torque for reinstallation.
Tightening Torque
(a): 50 N
.m (5.0 kg-m, 36.5 lb-ft)

YH4
GRAND
VITARA
DIFFERENTIAL (FRONT) 7E-15
A: Match marks
1. Mounting bracket bolt
2. Flange bolt and nut
1. Bolts
1. Mounting bracket bolt
2. Mounting bracket R
3. Differential housing
DISMOUNTING
1) Lift up vehicle and drain oil.
2) Disconnect air hose and breather hose from differential housing.
3) Before removing propeller shaft, give match marks on joint
flange and propeller shaft as shown.
4) Remove propeller shaft flange by removing its 4 bolts and sus-
pend it with cord or the like.
NOTE:
If pull out propeller shaft, transfer oil must be drained be-
fore pulling out.
5) Remove 3 bolts for left mounting bracket and 3 bolts for drive
shaft flange to set left side of differential free.
6) Remove 2 bolts from cross member to set differential rear
mounting free.
7) With differential housing assembly held with transmission jack,
remove mounting bolts on right end of housing.

YH4
GRAND
VITARA
7E-16 DIFFERENTIAL (FRONT)
(a)
(a)
(a)
1. Drive shaft joint R
2. Differential housing3. Transmission jack
4. Screw driver
8) Using 2 large screwdrivers as levers, pull out right side drive
shaft joint from differential and dismount housing assembly from
vehicle.
CAUTION:
During above work, use care not to cause damage to
drive shaft boot.
REMOUNTING
For remounting, reverse dismounting procedure and use following
tightening torque.
Tightening Torque
(a): 50 N
.m (5.0 kg-m, 36.5 lb-ft)
After tightening all fasteners properly, fill hypoid gear oil as speci-
fied and check tightening of plugs with specification.

YH4
GRAND
VITARA
DIFFERENTIAL (FRONT) 7E-17
09951-16080
Bearing installer09951-26010
Bush remover plate09918-18110
Air pressure regulator
09367-04002
3-way joint
UNIT REPAIR
Refer to the same section of UNIT REPAIR MANUAL mentioned in FOREWORD of this manual.
TIGHTENING TORQUE SPECIFICATIONS
FasteningportionTightening torqueFastening ortionN.mKg-mlb-ft
Differential oil filler / level plug232.317.0
Differential oil drain plug232.317.0
Differential mounting front bolts858.561.5
Differential mounting bracket bolts505.036.5
Front drive shaft flange bolts505.036.5
Propeller shaft flange bolts505.036.5
Pump assembly bolts131.39.5
REQUIRED SERVICE MATERIAL
MATERIALRECOMMENDED
SUZUKI PRODUCTUSE
SealantSUZUKI BOND NO. 1215
(99000-31110)Front differential drain plug
SPECIAL TOOLS

YH4
GRAND
VITARA
LIGHTING SYSTEM 8B-5
CLEARANCE, TAIL AND LICENCE PLATE LIGHTS
TroublePossible causeCorrection
All lights do not light
ªTAILº fuse blown

Lighting switch faulty

Wiring or grounding faultyReplace fuse to check for short
Replace switch
Repair
Some lights do not light
up
Bulb(s) blown

Wiring or grounding faultyReplace bulb(s)
Repair
BACK-UP LIGHTS
TroublePossible causeCorrection
Back-up lights do not
light
ªTURN / BACKº fuse blown (Hard Top Model)
ªTRNº fuse blown (Canvas Top Model)

Bulb blown

 
  
 switch faulty

Wiring or grounding faultyReplace fuse to check for short
Replace bulb
Replace switch
Repair
Back-up lights remains
ON
Back-up light switch or shift switch faulty

Wiring or grounding faultyReplace switch
Repair
BRAKE LIGHTS
TroublePossible causeCorrection
Brake lights do not light
up
ªSTOP / HORNº fuse blown (Hard Top
Model)
ªSTPº fuse blown (Canvas Top Model)

Bulb(s) blown

Brake light switch faulty

Wiring or grounding faultyReplace fuse to check for short
Replace bulb(s)
Adjust or replace switch
Repair
Brake lights stay on
Brake light switch faultyAdjust or replace switch
Only one light does not
light
Bulb blown

Wiring or grounding faultyReplace bulb
Repair
REAR FOG LIGHT (IF EQUIPPED)
TroublePossible causeCorrection
Rear fog light does not
come on
ªFOGº fuse blown

Rear fog light switch faulty

Lighting switch faulty

Wiring or grounding faulty

Bulb blownReplace fuse to check for short
Replace fog light switch
Replace switch
Repair
Replace bulb
INTERIOR LIGHTS
TroublePossible causeCorrection
Interior light (s) does (do)
not light up
Bulb(s) blown

ªDOMEº fuse blown (Hard Top Model)
ªDOMº fuse blown (Canvas Top Model)

Wiring or grounding faulty

Door switch faulty

Interior light switch faultyReplace bulb(s)
Replace fuse to check for short
Repair
Replace switch
Replace light assy
Front spot lights do not
light up
Bulb(s) blown

Wiring or grounding faulty

Spot light switch faultyReplace bulb(s)
Repair
Replace light assy

YH4
GRAND
VITARA
Terminal
Wire ColorSwitch Position
Terminal
Switch Position
Wire Color
HEAD
OFFHI
PASS SMALL
8B-6 LIGHTING SYSTEM
ON-VEHICLE SERVICE
HEADLIGHTS
HEADLIGHT SWITCH (IN COMBINATION SWITCH)
INSPECTION
1) Disconnect negative cable at battery.
2) Disconnect combination switch lead wire coupler.
3) Check for continuity between terminals at each switch position
shown below. If check result is not as specified, replace switch.
Lighting Switch
ELTH
WGR
OFF
SMALL
HEAD
Dimmer & Passing Switch
EDHLHUHF
W/BR/WRR/B
Passing (PASS)
Low Beam
High Beam (HI)
REMOVAL AND INSTALLATION
For vehicle without air bag system, refer to Section 3C COMBINA-
TION SWITCH, and for vehicle with air bag system, refer to Section
3C1 CONTACT COIL AND COMBINATION SWITCH ASSEMBLY.
REMOVAL
1) Disconnect negative cable at battery.
2) Remove front grille.
3) Disconnect harness and couplers from headlight assembly.
4) Remove three bolts and pull headlight assembly off vehicle.
INSTALLATION
Reverse removal procedure for installation.
Make sure to follow HEADLIGHT AIMING WITH SCREEN and aim
headlight after installation.

YH4
GRAND
VITARA
LH steering vehicle shown
X-X:Horizontal center line of headlight bulbs
A-A:Vertical center line of left headlight bulb
B-B:Vertical center line of right headlight bulb1. Screen
2. For right / left adjustment
3. For up / down adjustment
(for vehicle without leveling system)
4. For up / down adjustment
(for vehicle with leveling system)
5. Headlight leveling actuatorHOT
SPOT LH. HEADLIGHT RH. HEADLIGHT
LIGHTING SYSTEM 8B-7
BULB REPLACEMENT
WARNING:
Don't touch when the bulb is hot.
1) Disconnect negative cable at battery.
2) Disconnect harness from bulb.
3) Remove socket cover and bulb.
4) Replace bulb and install in reverse removal procedure.
HEADLIGHT AIMING WITH SCREEN
NOTE:

Unless otherwise obligated by local regulations, adjust
headlight aiming according to following procedure.

After replacing headlight, be sure to perform its aiming.

When inspecting and adjusting headlight with leveling sys-
tem, make sure to set the leveling switch to ª0º position with
IG switch ON.
Before adjustment, make sure the following.
a) Place vehicle on a flat surface in front of blank wall as below
ahead of headlight surface.
Clearance ªaº: 10 m (32.8 ft)
b) Adjust air pressure of all tires to a specified value respectively.
c) Bounce vehicle body up and down by hand to stabilize suspen-
sion.
d) Carry out one driver aboard.
Driver's weight: 75 kg (165 lb)
Adjustment
1) Check to see if hot spot (high intensity zone) of each main (low)
beam axis falls as illustrated.
Clearance ªHº: Approx. 130 mm (5.15 in.)
2) If headlight aiming is not set properly, align it to specification by
adjusting aiming screw and aiming gear.

YH4
GRAND
VITARA
LIGHTING SYSTEM 8B-11
REAR FOG LIGHT (IF EQUIPPED)
REAR FOG LIGHT SWITCH
INSPECTION
Check for continuity between terminals at each switch position
shown below. Hold the switch button (ON or OFF) pushed in during
checking switch.
NOTE:
Rear fog light lights up only when headlights (low or high
beams) or front fog lights (if equipped) are ON.
Rear fog lights turns OFF automatically when headlights or
front lights are turned OFF.