front SUZUKI GRAND VITARA 1999 2.G Service Workshop Manual

YH4
GRAND
VITARA
BODY SERVICE 9-17
1. Stopper pin
1. Rags
2. Wooden piece
1. Upper hinge
mounting bolts
2. Lower hinge
mounting bolt
3. Door
4. Body
1. Front door hinge
2. Upper hinge nut (rear door)
3. Rear door hinge
BODY STRUCTURE
FRONT DOOR ASSEMBLY
REMOVAL
1) Remove front fender. Refer to ªFRONT FENDERº in this section.
2) Disconnect door harness lead wires at each coupler.
3) Remove stopper pin.
4) Support door panel using a jack with a piece of wood placed be-
tween jack and panel, as shown.
5) Remove door assembly by loosening hinge mounting bolts.
INSTALLATION
Reverse removal procedure to install door assembly, noting follow-
ing point.
NOTE:
When replacing door, coat replacement door inside with wax
for proper anticorrosion treatment.
Refer to ªUNDERCOATING / ANTI-CORROSION COMPOUND
APPLICATION AREAº in this section.

Tighten door hinge bolts (and nut) to specified torque.
Tightening torque
(a): 27 N
.m (2.7 kg-m, 19.5 lb-ft)
(b): 23 N
.m (2.3 kg-m, 17.0 lb-ft)

Adjust door latch striker position by referring to ªFRONT DOOR
LOCK INSTALLATIONº section so that door is positioned correctly.

Adjust front door cushion so that door contacts body when closed.

After installation, open and close the door to check looseness.
Replace door open stopper pin when there is looseness.

When weatherstrip is hardened, water leak may develop.
In such case, replace it with new one.

YH4
GRAND
VITARA
9-18 BODY SERVICE
REAR DOOR ASSEMBLY
REMOVAL / INSTALLATION
Follow procedures for Front Door removal / installation in this sec-
tion.

YH4
GRAND
VITARA
BODY SERVICE 9-21
1. Hood lock
2. Hood lock bolts
3. Match marks
1. Hood cushion
HOOD
REMOVAL
1) Remove window washer hose from hood.
2) Remove four mounting bolts to detach hood.
ADJUSTMENT

Fore-and-aft and right-and-left adjustment.
Loosen four mounting bolts for adjustment.

Hood lock adjustment
When installing hood lock, bring bolt at intersection point of match
marks and move it in vertical direction for adjustment, if neces-
sary.
Tightening Torque
(a): 10 N
.m (1.0 kg-m, 7.5 lb-ft)

Vertical adjustment
If only one side (right or left) of hood is not level with front fender,
make it level by tightening or loosening hood cushion.
INSTALLATION
Reverse removal procedure to install hood.
INSPECTION
Check that secondary latch operates properly (check that second-
ary latch keeps hood from opening all the way even when pulling
hood release handle inside vehicle.) Also check that hood opens
and closes smoothly and properly and hood locks securely when
closed.
If any malfunction is found, lubricate hinge and latch, or repair hood
lock system.

YH4
GRAND
VITARA
1. Side body
2. Fender
3. Pad
1. Side body
2. Pad
3. Knife
9-22 BODY SERVICE
1. Front fender
2. Front fender lining
3. Fender attaching bolts
4. Fender lining attaching screws
FRONT FENDER
REMOVAL
1) Remove front bumper.
2) Remove fender splush guard (H25 engine).
3) Remove front fender lining.
4) Remove front fender.
INSTALLATION
1) Remove pad from side body and (or) fender, using care not to
damage painted surface.
2) Attach new pad cutting appropriately size temporarily and adjust
height with a knife so that fender becomes flush with side body.
3) Reverse removal procedure for installation.
NOTE:
If paint on fender bolt is peeled off, be sure to apply paint
again.

YH4
GRAND
VITARA
BODY SERVICE 9-23
1. Front bumper
2. Screws
3. Front bumper member
4. Side marker
FRONT BUMPER
NOTE:

Fasteners are important attaching parts in that they could affect the performance of vital components
and systems, and / or could result in major repair expense. They must be replaced with one of the same
part number or with an equivalent part if replacement becomes necessary.
Do not use a replacement part of lesser quality or substitute design. Torque values must be used as spe-
cified during reassembly to assure proper retention of these parts.

Before removing front bumper, remove fender lining and disconnect connector of side marker.

YH4
GRAND
VITARA
BODY SERVICE 9-25
a. Front bumper
b. 1st mounting
c. Suspension frame
d. Front strut
e. Suspension arm
f. 2nd mounting
g. ù20 zig hole
h. Zig hole
i. 3rd mounting
j. Lower rod
k. Upper rod
l. Lateral rod
m. Rear shock absorber
n. 4th mounting
o. Fuel tank
p. Fuel tank
q. Lower roda ± g : 1315 mm (51.77 in.)
a ± g' : 1534 mm (60.39 in.)
b ± g : 1243 mm (48.94 in.)
b ± g' : 1518 mm (59.76 in.)
c ± g : 1377 mm (54.21 in.)
c ± g' : 1105 mm (43.50 in.)
d ± g' : 1319 mm (51.93 in.)
d ± f : 874 mm (34.41 in.)
e ± g : 525 mm (20.67 in.)
e ± g' : 857 mm (33.74 in.)
f ± g' : 927 mm (36.50 in.)
h ± i : 178 mm (7.01 in.)
h ± j : 133 mm (5.24 in.)
h ± k : 325 mm (12.80 in.)
h ± l : 674 mm (26.54 in.)h ± m : 803 mm (31.61 in.)
h ± n : 1161 mm (45.71 in.)
h ± o : 1184 mm (46.61 in.)
h ± p : 1190 mm (46.85 in.)
i ± q : 999 mm (39.33 in.)
j ± q : 997 mm (39.25 in.)
k ± q : 824 mm (32.44 in.)
l ± q : 1130 mm (44.49 in.)
m ± q : 1258 mm (49.53 in.)
n ± q : 1483 mm (58.39 in.)
o ± q : 1349 mm (53.11 in.)
p ± q : 1334 mm (52.52 in.)
For 4 door model
g' ± q : 1275 mm (50.20 in.)
g ± q : 1534 mm (60.39 in.)
For 2 door model
g' ± q : 995 mm (39.17 in.)
g ± q : 1310 mm (51.57 in.)
UNDER BODY DIMENSIONS

YH4
GRAND
VITARA
Hole to hole distance
ªa ± gº : 276 mm (10.87 in.)
ªa ± kº : 1000 mm (39.37 in.)
ªb ± b'º : 1302 mm (51.26 in.)
ªb ± gº : 730 mm (28.74 in.)
ªc ± c'º : 668 mm (26.30 in.)
ªc ± eº : 414 mm (16.30 in.)
ªc ± gº : 406 mm (15.98 in.)
ªc ± jº : 1029 mm (40.51 in.)
ªc ± kº : 1000 mm (39.37 in.)
ªd ± d'º : 1302 mm (51.26 in.)
ªd ± eº : 189 mm (7.44 in.)
ªd ± c'º : 1016 mm (40.00 in.)
ªd ± gº : 672 mm (26.46 in.)
ªd ± kº : 968 mm (38.11 in.)
ªe ± e'º : 1456 mm (57.32 in.)ªf ± f'º : 1550 mm (61.02 in.)
ªf ± hº : 299 mm (11.77 in.)
ªf ± jº : 811 mm (31.93 in.)
ªg ± kº : 854 mm (33.62 in.)
ªh ± h'º : 1339 mm (52.72 in.)
ªh ± j'º : 1504 mm (59.21 in.)
ªh ± jº : 677 mm (26.65 in.)
ªh ± kº : 927 mm (36.50 in.)
ªi ± i'º : 1344 mm (52.91 in.)
ªi ± jº : 391 mm (15.39 in.)
ªi ± kº : 760 mm (29.92 in.)
ªj ± j'º : 1348 mm (53.07 in.)
ªj ± kº : 676 mm (26.61 in.)
ªl ± jº : 961 mm (37.83 in.)
ªl ± kº : 1018 mm (40.08 in.)
a. Front bumper installation clip hole
b (b'). Front bumper installation hole
c (c'). Headlight installation hole
d (d'). Headlight installation resin nut hole
e (e'). Headlight installation hole
f (f'). Front fender installation hole
g. Center member installation hole
h (h'). Fender installation reference hole
i (i'). Fender installation hole
j (j'). Fender installation reference hole
k. Garnish installation clip hole
l. Mounting installation hole
9-26 BODY SERVICE
BODY DIMENSIONS
4 door model, 2 door model

YH4
GRAND
VITARA
ªh ± h'º : 1521 mm (59.88 in.)
ªh ± oº : 901 mm (35.47 in.)
ªi ± i'º : 1547 mm (60.91 in.)
ªj ± nº : 806 mm (31.73 in.)
ªj ± j'º : 1511 mm (59.49 in.)
ªj ± oº : 649 mm (25.55 in.)
ªk ± k'º : 1126 mm (44.33 in.)
ªk ± oº : 1350 mm (53.15 in.)
ªl ± l'º : 1491 mm (58.70 in.)
ªl ± oº : 1130 mm (44.49 in.)
ªm ± m'º: 939 mm (36.97 in.)
ªm ± oº : 1725 mm (67.91 in.) Hole to hole distance
ªa ± cº : 982 mm (38.66 in.)
ªb ± b'º : 1390 mm (54.72 in.)
ªb ± c'º : 1406 mm (55.35 in.)
ªb ± cº : 755 mm (29.72 in.)
ªc ± c'º : 1012 mm (39.84 in.)
ªd ± d'º : 1545 mm (60.83 in.)
ªd ± nº : 800 mm (31.50 in.)
ªe ± e'º : 1110 mm (43.70 in.)
ªe ± nº : 1036 mm (40.79 in.)
ªf ± f'º : 1511 mm (59.49 in.)
ªf ± nº : 620 mm (34.41 in.)
ªg ± g'º : 1085 mm (42.72 in.)
ªg ± oº : 1099 mm (43.27 in.)
a. Garnish installation clip hole
b (b'). Front end of front windshield lower installation section
c (c'). Front end of front windshield upper installation section
d. Hole in F door lower hinge at rear
e. Trim installation clip hole
f (f'). Scuff installation hole (at rearmost end)
g (g'). Trim installation hole
h (h'). Hole in R door upper hinge in upper part
i (i'). Hole in R door lower hinge in lower part
j (j'). Rear scuff installation hole (at front end)
k (k'). Trim installation hole
l (l'). R door striker lower section installation hole
m (m'). Trim installation hole
n. Installation hole for F seat front inside
o. Installation hole for F seat rear inside
Opposite side of the point shown in figure
BODY SERVICE 9-27
4 door model

YH4
GRAND
VITARA
Hole to hole distance
a ± c : 981 mm (38.62 in.)
b ± b' : 1390 mm (54.72 in.)
b ± c' : 1404 mm (55.28 in.)
c ± c' : 1008 mm (39.69 in.)
e ± e' : 1110 mm (43.70 in.)
e ± i : 1036 mm (40.79 in.)
f ± i : 688 mm (27.09 in.)g ± g' : 1145 mm (45.08 in.)
g ± h : 1017 mm (40.04 in.)
g ± j : 1078 mm (42.44 in.)
h ± h' : 1338 mm (52.68 in.)
h ± j : 1459 mm (57.44 in.)
j ± k : 548 mm (21.57 in.)
l ± l' : 956 mm (37.64 in.)
a. Garnish installation clip hole
b (b'). Front end of front windshield lower installation section
c (c'). Front end of front windshield upper installation section
d. Hole in F door lower hinge at rear
e. Trim installation clip hole
f (f'). Scuff installation hole (at rearmost end)
g (g'). Trim installation hole
h (h').
11 jig hole
i. Installation hole for F seat front inside
j. Installation hole for F seat rear inside
k (k'). F seat belt installation hole
l (l'). Innermost end of side body installation section
9-30 BODY SERVICE
2 door model

YH4
GRAND
VITARA
1. Seat cushion
2. Seat back
3. Reclining assy (RH side)
4. Reclining assy (LH side)
5. Seat adjuster (RH outside)
6. Seat adjuster (RH inside)
7. Seat adjuster (LH outside)
8. Seat adjuster (LH inside)
Tightening Torque
(a): 35 N
.m (3.5 kg-m, 25.5 lb-ft)
(b): 23 N.m (2.3 kg-m, 17.0 lb-ft)
1. Cover
2. Coupler(b)
9-34 BODY SERVICE
SEAT
FRONT SEAT
REMOVAL
1) Disconnect lead wire(s) at coupler (if equipped). Remove four
mounting bolts fixing front seat to seat rail to remove front seat.
2) Disassemble and repair seat as necessary.
INSTALLATION
Reverse removal procedure to install front seat.
Torque to specifications, as shown.
Tightening Torque
(a): 35 N
.m (3.5 kg-m, 25.5 lb-ft)