SUZUKI GRAND VITARA 1999 2.G Service Workshop Manual
GRAND VITARA 1999 2.G
SUZUKI
SUZUKI
https://www.carmanualsonline.info/img/20/7582/w960_7582-0.png
SUZUKI GRAND VITARA 1999 2.G Service Workshop Manual
Page 656 of 801
YH4
GRAND
VITARA
1. Side body inner panel
2. Rear wheel housing outer rear panel
3. Rear wheel housing panel
4. Rear floor panel
5. Tail lower member
6. Center floor panel
7. Front floor panel
8. Center floor member
9. Side sill inner panel
10. Side outer panelªAº: Apply sealant
ªBº: Brush treatment
9-38 BODY SERVICE
SEALANT APPLICATION AREA
4 door model
Page 657 of 801
YH4
GRAND
VITARA
1. Cowl top panel
2. Dash panel
3. Cowl front panel
4. Front floor panel
5. Front pillar inner lower panelªAº: Apply sealant
ªBº: Brush treatment
BODY SERVICE 9-39
Page 658 of 801
YH4
GRAND
VITARA
9-40 BODY SERVICE
1. Side body inner panel
2. Side body outer panel
3. Back pillar outer panel
4. Front pillar inner panel
5. Roof panel
6. Front pillar upper reinforcement
7. Rear wheel housing panel
8. Fuel inlet boxªAº: Apply sealant
ªBº: Brush treatment
Page 665 of 801
YH4
GRAND
VITARA
1. Side body inner panel
2. Rear wheel housing panel
3. Rear floor panel
4. Center floor panel
5. Front floor panel
6. Center floor member
7. Side sill inner panelªAº: Apply sealant
ªBº: Brush treatment
BODY SERVICE 9-47
2 DOOR MODEL
Page 666 of 801
YH4
GRAND
VITARA
9-48 BODY SERVICE
1. Cowl top panel
2. Dash panel
3. Cowl front panel
4. Front floor panel
5. Front pillar inner lower panelªAº: Apply sealant
ªBº: Brush treatment
Page 667 of 801
YH4
GRAND
VITARA
BODY SERVICE 9-49
1. Side body inner panel
2. Side body outer panel
3. Front pillar inner panel
4. Front pillar upper reinforcement
5. Rear wheel housing panel
6. Fuel inlet box
7. Center pillar reinforcement
8. Center pillar joint outer panel
9. Center pillar joint inner panel
10. Tail upper member
11. Back pillar outer panelªAº: Apply sealant
ªBº: Brush treatment
ªCº: Wipe
Page 670 of 801
YH4
GRAND
VITARA
ªaº: 30 mm (1.18 in.)
ªbº: 100 mm (3.94 in.)
ªAº: Apply undercoating (PVC, 400 m or more)
ªBº: Additional applying of under coating
ªBº: (for 5 door vehicle without splush guard)
ªCº: Apply PVC chip resistant material (200 m or more)1. Side body outer
2. Side sill inner
3. Main floor
4. Front fender
5. Front wheel housing
6. Frame
7. Dash panel
8. Center floor
9. Rear floor
Vehicle produced in IWATA
VIEW: Z
9-52 BODY SERVICE
Page 671 of 801
YH4
GRAND
VITARA
ªaº: 30 mm (1.18 in.)
ªbº: 100 mm (3.94 in.)
ªAº: Apply undercoating (PVC, 400 m or more)
ªBº: Additional applying of under coating
ªBº: (for 5 door vehicle without splush guard)
ªCº: Apply PVC chip resistant material (200 m or more)1. Side body outer
2. Side sill inner
3. Main floor
4. Front fender
5. Front wheel housing
6. Frame
7. Dash panel
8. Center floor
9. Rear floor
Vehicle produced in CAMI
VIEW : Z
BODY SERVICE 9-53
Page 674 of 801
YH4
GRAND
VITARA
9-56 BODY SERVICE
BADC
ªaº: 30 mm (1.18 in.)
ªbº: 100 mm (3.93 in.)
ªAº: Apply undercoating (PVC, 400 m or more)
ªBº: Additional applying of under coating
ªBº: (for 5 door vehicle without splush guard)
ªCº: Apply PVC chip resistant material (200 m or more)1. Side body outer
2. Side sill inner
3. Main floor
4. Front fender
5. Front wheel housing
6. Frame
7. Dash panel
8. Center floor
9. Rear floorB ± B
A ± A
C ± C
VIEW : Z
Page 677 of 801
YH4
GRAND
VITARA
BODY SERVICE 9-59
1. Door latch
2. Outside handle
3. Inside handle bezel
4. Latch striker
1. Door opening control rod pin retainer
2. Door opening control rod
3. Door lock control rod
3
SECURITY AND LOCKS
FRONT DOOR LOCK ASSEMBLY
REMOVAL
1) Raise window all the way up.
2) Remove door trim and door sealing cover, refer to steps 1) to 6)
of FRONT DOOR GLASS REMOVAL in this section.
3) Remove door opening control rods.
Unlock door lock rod pin retainer and disconnect control rod.
4) Remove door lock control rod.
5) Disconnect door lock motor lead wire (if equipped).
6) Remove lock assembly.
