Seat SUZUKI GRAND VITARA 2000 2.G Service User Guide

YH4
GRAND
VITARA
[A]
[B]

Hard Cornering

Under-Inflation

Lack of Rotation
Incorrect Wheel Alignment

Tire Construction Non-Uniformity

Wheel Heavy Acceleration [A] [B]
3-6 STEERING, SUSPENSION, WHEELS AND TIRES
TIRE DIAGNOSIS
IRREGULAR AND / OR PREMATURE WEAR
Irregular and premature wear has many possible causes. Some of
them are: incorrect inflation pressures, lack of tire rotation, driving
habits, improper alignment.
If the following conditions are noted, rotation is in order:
1. Front tire wear is different from rear.
2. Uneven wear exists across the tread of any tire.
3. Left front and right front tire wear is unequal.
4. Left rear and right rear tire wear is unequal.
5. There is cupping, flat spotting, etc.
A wheel alignment check is in order if the following conditions are
noted:
1. Left front and right front tire wear is unequal.
2. Wear is uneven across the tread of any front tire.
3. Front tire treads have scuffed appearance with ªfeatherº edges
on one side of tread ribs or blocks.
WEAR INDICATOR
The original equipment tires have built-in tread wear indicators to
show when tires need replacement. These indicators will appear as
12 mm (0.47 in.) wide bands when the tire tread depth becomes 1.6
mm (0.063 in.). When the indicators appear in 3 or more grooves
at 6 locations, tire replacement is recommended.
RADIAL TIRE WADDLE
Waddle is side to side movement at the front and / or rear of the ve-
hicle. It is caused by the steel belt not being straight within the tire.
It is most noticeable at low speed, 8 to 48 km / h (5 to 30 mph). It is
possible to road test a vehicle and tell on which end of the vehicle
the faulty tire is located. If the waddle tire is on the rear, the rear end
of the vehicle will shake from side to side or ªwaddleº. From the driv-
er's seat it feels as though someone is pushing on the side of the
vehicle. If the faulty tire is on the front, the waddle is more visual.
The front sheet metal appears to be moving back and forth and the
driver feels as though he is at the pivot point in the vehicle.
Waddle can be quickly diagnosed by using a Tire Problem Detector
(TPD) and following the equipment manufacturer's recommenda-
tions.
If a TPD is not available, the more time consuming method of sub-
stituting known good tire / wheel assemblies on the problem vehicle
can be used as follows:

YH4
GRAND
VITARA
14
15
1. Driver air bag (inflator) module
2. Steering wheel
3. Steering wheel nut
4. Contact coil and combination switch assembly
5. Steering column upper cover
6. Steering column lower cover
7. Steering column assembly
8. Steering lock assembly
9. Steering column hole cover
10. Steering shaft joint
11. Steering lower shaft assembly
12. Adjustable steering column release lever
(if equipped)
13. Steering column lower seal
14. With adjustable steering column release lever type
15. Without adjustable steering column release lever type
3C1-2 AIR BAG STEERING WHEEL AND COLUMN
GENERAL DESCRIPTION
This double tube type steering column has the following three important features in addition to the steering function:

The column is energy absorbing, designed to compress in a front-end collision.

The ignition switch and lock are mounted conveniently on this column.

With the column mounted lock, the ignition and steering operations can be locked to inhibit theft of the vehicle.
To insure the energy absorbing action, it is important that only the specified screws, bolts, and nuts be used as
designated and that they are tightened to the specified torque. When the column assembly is removed from the
vehicle, special care must be taken in handling it. Use of a steering wheel puller other than the one recommended
in this manual or a sharp blow on the end of the steering shaft, leaning on the assembly, or dropping the assembly
could shear the plastic shear pins which maintain column length and position.
The driver air bag (inflator) module is one of the supplemental restraint (air bag) system components and is
mounted to the center of the steering wheel. During certain frontal crashes, the air bag system supplements the
restraint of the driver's and passenger's seat belts by deploying the air bags. The air bag (inflator) module should
be handled with care to prevent accidental deployment. When servicing, be sure to observe all WARNINGS in this
section. Refer to ªSERVICE PRECAUTIONSº in Section 10B.

YH4
GRAND
VITARA
3D
FRONT SUSPENSION 3D-1
GENERAL DESCRIPTION3D- 2 . . . . . . . . . . . . . .
DIAGNOSIS3D- 3 . . . . . . . . . . . . . . . . . . . . . . . . . . .
Diagnosis Table 3D- 3. . . . . . . . . . . . . . . . . . . . . .
Stabilizer Bar and Bushing Check 3D- 3. . . . . .
Strut Damper and / or Coil Spring Check 3D- 3. .
Suspension Arm / Knuckle Check 3D- 3. . . . . . . .
Suspension Control Arm Joint Check 3D- 4. . . .
Suspension Control Arm Bushing Check 3D- 4.
Wheel Disc, Nut & Bearing Check 3D- 4. . . . . .
ON-VEHICLE SERVICE3D- 5 . . . . . . . . . . . . . . . . Stabilizer Bar / Bushings 3D- 5. . . . . . . . . . . . . . .
Strut Damper 3D- 6. . . . . . . . . . . . . . . . . . . . . . . .
Coil Spring 3D- 8. . . . . . . . . . . . . . . . . . . . . . . . . .
Bump Stopper / Spring Rubber Seat 3D-11. . . . .
Wheel Hub (Included Wheel Bearing) 3D-12. . .
Knuckle / Wheel Spindle 3D-17. . . . . . . . . . . . . . . .
Suspension Control Arm / Bushings 3D-21. . . . . .
TIGHTENING TORQUE
SPECIFICATIONS3D-23 . . . . . . . . . . . . . . . . . . . .
REQUIRED SERVICE MATERIALS3D-24 . . . . . .
SPECIAL TOOLS3D-25 . . . . . . . . . . . . . . . . . . . . . .
SECTION 3D
FRONT SUSPENSION
CAUTION:

All front suspension fasteners are an important attaching part in that it could affect the performance
of vital parts and systems, and / or could result in major repair expense. They must be replaced with
one of the same part number or with an equivalent part if replacement becomes necessary. Do not
use a replacement part of lesser quality or substitute design. Torque values must be used as specified
during reassembly to assure proper retention of this part.

Never attempt to heat, quench or straighten any front suspension part. Replace it with a new part or
damage to the part may result.
CONTENTS

YH4
GRAND
VITARA
FRONT SUSPENSION 3D-3
DIAGNOSIS
DIAGNOSIS TABLE
Refer to Section 3.
STABILIZER BAR AND BUSHING CHECK
BAR
Inspect for damage or deformation. If defective, replace.
BUSHING
Inspect for damage, wear or deterioration. If defective, replace.
STRUT DAMPER AND / OR COIL SPRING
CHECK
1) Inspect strut for oil leakage. If strut is found faulty, replace it as
an assembly unit, because it can not be disassembled.
2) Strut function check
Check and adjust tire pressures as specified.
Bounce body three or four times continuously by pushing front
end on the side with strut to be checked. Apply the same amount
of force at each push and note strut resistance both when
pushed and rebounding.
Also, note how many times vehicle body rebounds before com-
ing to stop after hands are off. Do the same for strut on the other
side.
Compare strut resistance and number of rebound on the right
with those on the left.
And they must be equal in both. With proper strut, body should
come to stop the moment hands are off or after only one or two
small rebounds. If struts are suspected, compare them with
known good vehicle or strut.
3) Inspect for damage or deformation.
4) Inspect strut boot for damage or crack.
5) Inspect for cracks or deformation in spring seat.
6) Inspect for deterioration of bump stopper.
7) Inspect strut mount for wear, cracks or deformation.
Replace any parts found defective in steps 2) ± 7).
SUSPENSION ARM / KNUCKLE CHECK
Inspect for cracks, deformation or damage.

YH4
GRAND
VITARA
3D-10 FRONT SUSPENSION
ªaº < ªbº
1. Circlip
2. Large diameter
1. Axle shaft drive flange
2. Bolt 1. Spring seat
Bottom
INSTALLATION
Reverse removal procedure to install coil spring.
NOTE:
Upper and lower diameters of coil spring are different.
Bring larger diameter end at bottom and set its open end in
place on spring seat.

Be sure to use specified torque for tightening each fastener.

Refer to torque specification chart at the end of this section.

As for ball stud nut, be sure to insert split pin and bend it after tight-
ening it.

Tighten tie-rod end nut with pushing ball stud to upper side so as
not ball stud to be rotated.

For 4WD vehicle
Apply lithium grease to front drive shaft washer and front wheel
spindle outer.
ªAº: Grease 99000-25010

For 4WD vehicle
When installing circlip to drive shaft, utilize screw hole in drive
shaft to pull it out and bring large diameter of circlip at right as
shown.

For 4WD vehicle
When installing axle shaft drive flange to wheel hub, apply sealant
to mating surface of axle shaft drive flange and tighten flange bolt
to specified torque.
ªAº: Sealant 99000-31090
Tightening Torque
(a): 50 N
.m (5.0 kg-m, 36.5 lb-ft)

YH4
GRAND
VITARA
FRONT SUSPENSION 3D-11
1. Front wheel speed sensor
2. Bolt
1. Spring rubber
seat
2. Bump stopper2, (b)
1

Check that no foreign material is attached to sensor and rotor.
Install wheel speed sensor and its harness clamp.
Tightening Torque
(a): 10 N
.m (1.0 kg-m, 7.5 lb-ft)
(b): 23 N
.m (2.3 kg-m, 17.0 lb-ft)
CAUTION:

Do not pull wire harness or twist more than necessary
when installing front wheel speed sensor.

Fit harness grommet to inner fender securely.

Check that there is no clearance between sensor and knuckle.
BUMP STOPPER / SPRING RUBBER SEAT
REMOVAL
1) Remove coil spring. Refer to steps 1) to 15) of item ªCOIL
SPRING REMOVALº in this section.
2) Remove spring rubber seat.
3) Remove bump stopper, using special tool.
Special Tool
(A): 09941-66010
INSTALLATION
1) Tighten bump stopper to specified torque, using special tool.
Tightening Torque
(a): 50 N
.m (5.0 kg-m, 36.5 lb-ft)
2) Install spring rubber seat.
3) Install coil spring. Refer to item ªCOIL SPRING INSTALLATIONº
in this section.

YH4
GRAND
VITARA
1. Rear axle housing
2. Spring seat
3. Coil spring
4. Stepped part
1. Body center
2. Body outside
1. Body center
2. Body outside 1. Parking brake
cable hanger
2. Cross member
3. Clamp
4. Chassis frame
REAR SUSPENSION 3E-7
INSTALLATION
1) Install coil spring on spring seat of axle housing and then raise
axle housing.
NOTE:
When seating coil spring, mate spring end with stepped
part of rear axle spring seat as shown.
2) Install shock absorber lower bolt. For its proper installing direc-
tion, refer to figure.
Nut should not be tightened.
3) Install wheel speed sensor clamp (if equipped) and E-ring, and
connect breather hose to axle housing.
4) Connect cable hanger to chassis frame and clamp to cross
member. Remove floor jack from axle housing.
5) Install wheel and tighten wheel nuts to specified torque.
Tightening Torque
(a): 100 N
.m (10.0 kg-m, 72.5 lb-ft)
6) Lower hoist and tighten absorber lower nut to specified torque.
Tightening Torque
(b): 85 N
.m (8.5 kg-m, 61.5 lb-ft)
NOTE:
For tightening of lower nut, refer to NOTE given under
SHOCK ABSORBER INSTALLATION in this section.

YH4
GRAND
VITARA
1. Lower rod
2. Body center
1. Rear axle housing
2. Spring seat
3. Coil spring
4. Stepped part
1. Axle housing ªAº 1. Body center
1
2
1
REAR SUSPENSION 3E-19
INSTALLATION
Install removed parts in reverse order of removal, noting the follow-
ing.
1) Place rear axle housing on floor jack. Then install upper / lower
rod rear mounting bolts (right & left) in proper direction as shown
(refer to UPPER ROD INSTALLATION for upper rod bolts). At
this time, mount nuts but don't tighten them.
2) Install coil spring (right & left) on spring seat of axle housing and
raise axle housing.
NOTE:
When seating coil spring, mate spring end with stepped
part of rear axle spring seat as shown.
3) Install lateral rod to rear axle housing.
4) Install lower part of shock absorber to right and left sides of axle
housing and install bolts in proper direction as shown in figure.
At this time, mount nuts but don't tighten them.
5) Clean mating surfaces of axle housing and differential carrier
and apply sealant to housing side.
ªAº: Sealant 99000-31110
6) Install differential carrier assembly to axle housing and tighten
carrier nuts to specified torque.
Tightening Torque
(a): 55 N
.m (5.5 kg-m, 40.0 lb-ft)

YH4
GRAND
VITARA
WHEELS AND TIRES 3F-7
TIRE
MOUNTING AND DEMOUNTING
Use tire changing machine to mount or demount tires. Follow equip-
ment manufacturer's instructions. Do not use hand tools or tire
irons alone to change tires as they may damage tire beads or wheel
rim.
Rim bead seats should be cleaned with wire brush or coarse steel
wool to remove lubricants, old rubber and light rust. Before mount-
ing or demounting tire, bead area should be well lubricated with ap-
proved tire lubricant.
After mounting, inflate to 240 kPa (35psi) so that beads are com-
pletely seated. Then adjust pressure to specified shown an tire
placard.
WARNING:
Do not stand over tire when inflating. Bead may break when
bead snaps over rim's safety hump and cause serious per-
sonal injury.
Do not exceed 240 kPa (35 psi) pressure when inflating. If
240 kPa (35 psi) pressure will not seat beads, deflate, re-lu-
bricate and reinflate. Over inflation may cause bead to break
and cause serious personal injury.
Install valve core and inflate to proper pressure.
TIRE REPAIR
There are many different materials and techniques on the market
to repair tires. As not all of these work on all types of tires, tire
manufacturers have published detailed instructions on how and
when to repair tires. These instructions can be obtained from the
tire manufacturer.

YH4
GRAND
VITARA
[A]: With ABS
[B]: Without ABS
1. Piston stopper circlip
2. Piston stopper
3. Cylinder cup
4. Plate
5. Primary piston
6. Piston cup
7. Primary piston return spring
8. Primary spring retainer
9. Secondary piston pressure cup
10. Secondary piston
11. Return spring secondary seat
12. Secondary piston return spring
13. Secondary piston stopper bolt
14. Master cylinder body
ªAº: Primary piston
ªBº: Secondary piston
[B] [A]
5A-2 BRAKES PIPE / HOSE / MASTER CYLINDER
GENERAL DESCRIPTION
MASTER CYLINDER ASSEMBLY
The master cylinder has two pistons and three piston cups. Its hydraulic pressure is produced in the primary (ªaº
in the figure below) and secondary (ªbº) chambers. The hydraulic pressure produced in the primary chamber (ªaº)
acts on the front (for vehicle without ABS, rear) wheel brakes.
Also, the hydraulic pressure produced in the secondary chamber (ªbº) acts on the rear (for vehicle without ABS,
front) wheel brakes.
NOTE:
Replace all components included in repair kits to service this master cylinder. Lubricate rubber parts with
clean, fresh brake fluid to ease assembly. Do not use lubricated shop air on brake parts as damage to rub-
ber components may result. If any hydraulic component is removed or brake line disconnected, bleed the
brake system.
The torque values specified are for dry, unlubricated fasteners.
BOOSTER ASSEMBLY
The booster is located between the master cylinder and the brake pedal. It is so designed that the force created
when the brake pedal is depressed is mechanically increased combined with the engine vacuum.
The booster has two diaphragms of
ù7.5 in. (191 mm) effective diameter.
CAUTION:

Never disassemble brake booster assembly. If it is found faulty, replace it with new assembly.

The torque values specified are for dry, unlubricated fasteners. If any hydraulic component is re-
moved or brake line disconnected, bleed the brake system.