6a1 SUZUKI JIMNY 2005 3.G Service Service Manual

Downloaded from www.Manualslib.com manuals search engine ENGINE MECHANICAL (M13 ENGINE) 6A1-33
Oil Pump
REMOVAL
1) Disconnect negative cable at battery.
2) Remove timing chain cover, referring to “Timing Chain
Cover” in this section.
DISASSEMBLY
1) Remove rotor plate (1) by removing its mounting bolts.
[A] : Sealant application
amount4. Timing chain cover 10. Circlip
: Apply sealant 99000-31140 to the mating surface of cylinder and
cylinder head.
: Apply sealant 99000-31150 to mating surface of timing chain cover
referring to the figure of Step 1) in “Timing Chain Cover Installation”.
“a” : 3 mm (0.12 in.) 5. Pin 11. Oil pump mounting bolt
“b” : 2 mm (0.08 in.) 6. Oil seal 12. Timing chain cover mounting bolts
1. Rotor plate 7. Relief valve Tightening torque
2. Outer rotor 8. Spring Do not reuse.
3. Inner rotor 9. Retainer Apply thin coat of engine oil to sliding
surface of each parts.

Downloaded from www.Manualslib.com manuals search engine 6A1-34 ENGINE MECHANICAL (M13 ENGINE)
2) Remove outer rotor (1) and inner rotor (2).
3) Remove relief valve (1), spring (2) and retainer (3) by remov-
ing circlip (4).
INSPECTION
Check oil seal lip for fault or other damage. Replace as nec-
essary.
Special tool
(A) : 09913-75520
NOTE:
When installing new oil seal (1), press-fit it till its end face
is flush with oil pump case (2) end face.

Downloaded from www.Manualslib.com manuals search engine ENGINE MECHANICAL (M13 ENGINE) 6A1-35
Check outer (1) and inner rotors (2), rotor plate, and oil pump
case for excessive wear or damage.
Check relief valve (1) for excessive wear or damage and
operates smoothly.
MEASUREMENT
Radial clearance
Check radial clearance between outer rotor (1) and case (2),
using thickness gauge (3).
If clearance exceeds its limit, replace outer rotor or case.
Limit on radial clearance between outer rotor and case for
oil pump
0.310 mm (0.0122 in.)
Side clearance
Using straight edge (1) and thickness gauge (2), measure side
clearance.
Limit on side clearance for oil pump inner rotor
0.15 mm (0.0059 in.)

Downloaded from www.Manualslib.com manuals search engine 6A1-36 ENGINE MECHANICAL (M13 ENGINE)
ASSEMBLY
1) Wash, clean and then dry all disassembled parts.
2) Apply thin coat of engine oil to inner and outer rotors, oil seal
lip portion, and inside surfaces of oil pump case and plate.
3) Install outer (1) and inner rotors (2) to oil pump case.
4) Install relief valve component (1) to rotor plate (2).
5) Install rotor plate and tighten all bolts to specified torque.
After installing plate, check to be sure that rotors turn
smoothly by hand (0.3 N·m (0.03 kg-m, 0.25 lb-ft) torque or
below).
Tightening torque
Oil pump rotor plate bolts (a) : 11 N·m (1.1 kg-m, 8.0 lb-ft)
INSTALLATION
For installation referring to “Timing Chain Cover” in this section.

Downloaded from www.Manualslib.com manuals search engine ENGINE MECHANICAL (M13 ENGINE) 6A1-37
Timing Chain and Chain Tensioner
REMOVAL
1) Remove timing chain cover referring to “Timing Chain
Cover”.
2) Align both intake and exhaust camshaft timing sprocket
marks (1) with notches (2) of cylinder head respectively by
turning crankshaft.
3) Remove timing chain tensioner adjuster assembly (3).
4) Remove timing chain tensioner (4).
5) Remove timing chain No.1 guide (5).
6) Remove timing chain (6) with crankshaft timing sprocket (7).
1. Crankshaft timing sprocket 5. Timing chain tensioner adjuster assembly Tightening torque
2. Timing chain 6. Chain tensioner adjuster mounting bolt Apply engine oil to sliding surface.
3. Timing chain No.1 guide 7. Chain tensioner mounting bolt
4. Timing chain tensioner 8. Chain guide mounting bolt
CAUTION:
After timing chain is removed, never turn crankshaft and
camshafts independently more than its allowable turning
range described in “INSTALLATION” section.
If turned, interference may occur between piston and
valves and valves themselves, and parts related to piston
and valves may be damaged.
45
6
21
1
3
7

Downloaded from www.Manualslib.com manuals search engine 6A1-38 ENGINE MECHANICAL (M13 ENGINE)
INSPECTION
Timing chain tensioner
Check shoe (1) for wear or damage.
Crankshaft timing sprocket
Check teeth of sprocket for wear or damage.
Timing chain
Check timing chain for wear or damage.
Timing chain tensioner adjuster
Check that tooth surface (1) are free from damage.
Timing chain No.1 guide
Check shoe (1) for wear or damage.

Downloaded from www.Manualslib.com manuals search engine ENGINE MECHANICAL (M13 ENGINE) 6A1-39
INSTALLATION
1) Check that match marks (1) on intake and exhaust camshaft
timing sprockets are in match with notches (2) on cylinder
head as shown in figure.
2) Set key (3) and turn crankshaft to position key on upside of
crankshaft.
3) Install timing chain by aligning dark blue plate (1) of timing
chain and mark (2) on camshaft timing sprocket and then
aligning dark blue plate (3) and triangle mark (4) as shown in
figure.
4) Fit crankshaft timing sprocket to timing chain by aligning gold
plate (5) of timing chain and mark (6) on crankshaft timing
sprocket. Then install crankshaft timing sprocket fitted with
chain to crankshaft.
5) Apply engine oil to sliding surface of timing chain No.1 guide
(1) and install it as shown in figure.
Tighten guide bolts to specified torque.
Tightening torque
Timing chain No.1 guide bolts
(a) : 9 N·m (0.9 kg-m, 6.5 lb-ft) CAUTION:
After timing chain is removed, never turn crankshaft and
camshafts independently more than such an extent (“a”,
“b”) as shown in figure.
If turned, interference may occur between piston and
valves and valves themselves, and parts related to piston
and valves may be damaged.
“a” :90°5. Crankshaft allowable turning range.
By key on crankshaft, within 90° from top on both right and left.
“b” :15°4. Camshaft (IN and EX) allowable turning range.
By marks on camshaft timing sprocket within 15° from notches on
cylinder head on both right and left.

Downloaded from www.Manualslib.com manuals search engine 6A1-40 ENGINE MECHANICAL (M13 ENGINE)
6) Apply engine oil to sliding surface of chain tensioner (1) and
install chain tensioner and spacer.
Tighten tensioner bolt to specified torque
Tightening torque
Timing chain tensioner bolt
(a) : 22 N·m (2.2 kg-m, 16.0 lb-ft)
7) Check that match marks (1) on intake and exhaust camshaft
timing sprockets are in match with dark blue plates (2) of tim-
ing chain and match mark (3) on crankshaft timing sprocket
is in match with gold plate (4) of timing chain.
8) Screw in plunger (1) by turning timing chain tensioner
adjuster (2) in arrow direction and install a retainer (3) (wire)
to hold plunger in place.
9) Install timing chain tensioner adjuster assembly (1) with a
retainer (2).
Tighten adjuster bolts to specified torque and then remove a
retainer from chain tensioner adjuster assembly.
Tightening torque
Timing chain tensioner adjuster bolts
(a) : 11 N·m (1.1 kg-m, 8.0 lb-ft)
221
3
4

Downloaded from www.Manualslib.com manuals search engine ENGINE MECHANICAL (M13 ENGINE) 6A1-41
10) Apply engine oil to timing chain and then turn crankshaft
clockwise by 2 revolutions and check that match marks (1)
on intake and exhaust camshaft timing sprockets are in
match with notches (2) on cylinder head and key (3) is on
upside of crankshaft as shown in figure.
If each mark of timing chain and each match mark are no
matches, adjust each sprocket and timing chain.
11) Install timing chain cover referring to “Timing Chain Cover” in
this section.
12) Perform Steps 3) to 8) of “INSTALLATION” of “Timing Chain
Cover” in this section.
21
1
3

Downloaded from www.Manualslib.com manuals search engine 6A1-42 ENGINE MECHANICAL (M13 ENGINE)
Camshaft, Tappet and Shim
REMOVAL
1) Remove cylinder head cover and oil pan referring to “Cylin-
der Head Cover” and “Oil Pan and Oil Pump Strainer” in this
section.
2) Remove timing chain cover referring to “Timing Chain Cover”
in this section.
3) Remove timing chain referring to “Timing Chain and Chain
Tensioner” in this section.
4) Loosen camshaft housing bolts in such order as indicated in
figure and remove them.
5) Remove camshaft housings.
6) Remove intake and exhaust camshafts.
1. Intake camshaft 4. Tappet Tightening torque
2. Exhaust camshaft 5. Camshaft housing Apply engine oil to sliding surface of each part.
3. Shim
: Shim No. on it faces tappet side.6. Camshaft housing bolt