sensor SUZUKI JIMNY 2020 Owner's Guide

OPERATING YOUR VEHICLE
Traffic sign recognition
(if equipped)
When the vehicle with the dual sensor passes the traffic sign, the traffic sign is shown on the information display on the cluster meter in order to notify the driver. This system may not work properly outside Europe.
60
..
A WARNING
The function of the traffic sign recog­nition has limits and may not func­tion properly depending on the driving conditions of circumstances. Do not rely excessively on this func­tion and always drive in a safe man~ ner.
3-39
NOTE: The traffic sign may be shown with delay on the information display depending on the circumstances and conditions of the vehicle The number of the traffic sign for this function shows up to three signs on the information display The traffic signs are disappeared on the information display under the following situations -When the vehicle was run in constant distance after showing the traffic signs on the information display (except for regulation end sign}, -When a period of time passed after the traffic signs on the information dis­play (only for regulation end sign), -When turning right or left with the turn signal lights blinked, -For manual transmission vehicle, the gearshift lever is in "R" position, for automatic transmission vehicle, the gearshift lever is in "P" or "R" position (except for speed limit sign). To change the traffic sign recognition setting, select "Sign recog." in "Setting mode" on the information display. Then, select "ON" or "OFF"
When the ignition switch was turned "OFF" with the speed limit sign shown on the information display and then the igni­tion switch is fumed "ON" again, the information display shows the same speed limit sign the last time the ignition switch was fumed "OFF" When you drive in the area where unit of velocity is changed, the traffic signs may not be appeared or the different traffic signs may be appeared on the informa­tion display after passing the actual traf­fic signs. This is not a malfunction. The display will be resumed after driving for a while. The speed limit sign on the information display that is higher or lower than the actual limited speed sign may be dis­played for the speed limit sign

Situations where the system does not activate Under the following situations, the system does not activate. When the engine is off When dual sensor brake support indica­tor light and lane departure warning indi­cator light are initially lighting immediately after the ignition switch is in "ON" position For manual transmission vehicle, the gearshift lever is in "R" position, for auto­matic transmission vehicle, the gearshift lever is in "P", "R", or "N" position When the dual sensor is temporarily stopped or malfunctioning When the ESP® OFF switch is pushed and the system is turned off When the traffic sign recognition is turned off by operating the setting mode of information display When parking brake is applied When you drive in the area that there are no speed limit signs and has speed limit
OPERATING YOUR VEHICLE
3-40

OPERATING YOUR VEHICLE
Types of recognized traffic signs
Information Type of the traffic sign message
[l[I Speed limit begins/ends
~~
No overtaking begins/ends
Speed limit with supplemental mark (Displayed simultaneously with speed limit)
Supplemental mark exists
I
(Display example)
~
All canceled (All restrictions canceled. Returns to default road regu-lation.)
NOTE: The above traffic signs are representative examples. The traffic signs may be different in every country.
3-41
Situations where the dual sensor may not activate properly There may be high possibility not to detect the traffic signs by the dual sensor under the following situations. Also the function of the dual sensor may be stopped tempo­rarily. When the situations are improved, the temporary stop of the function will be canceled. When there is bad weather such as heavy rain, fog or a blizzard When the dual sensor is hit by a bright light such as sunlight or the headlight of oncoming vehicle When there is a sight of similar tone and color such as a snowscape When the vehicle runs on the road which became bright by the reflected light, When there are no lights or lamps as street lamps, etc around in the dark Front visibility is poor due to that there is water vapor, sand or smoke or when the vehicle in front of you is surrounded by exhaust gas, water or snow When you drive in the dawn, the dusk and the night or when you drive in a dark place as an indoor parking lot When the vehicle direction to go ahead or the vehicle position was largely changed (for example, the lane change, left turn, or right turn), When the windshield is covered in fog, snow, ice or dirt

81M40380
When raindrop, water or dirt on the wind­shield is not wiped up enough While using the windshield washer When a wiper blade other than SUZUKI genuine parts, including short type wiper
blade is used When the tyres are not inflated to the recommended tyre inflation pressure or when the tyres except the assignment size are equipped,
72M20405
When your vehicle is weighed down by heavy items in the luggage compartment or rear seat
When the headlights are covered in dirt, snow, ice or mud When the optical axis of the headlight is deviated When the brightness changes extremely (for example, passing the entrance or exit of tunnel), When the vehicle is swaying on the rough roads (for example, unevenness roads or stone pavement roads) and the visibility of the monocular camera is unstable, There may be a case to display the traf­fic sign irrelevant to the vehicle, the traf­fic sign that is not existed around the vehicle under the following situations. -When the traffic sign is existed on the branched road, the junction or the adjacent lane near the road that the vehicle is moving, -When there are similar things to the color and the object of the traffic sign (for example, the similar traffic sign, the signboard or the structures) -When the vehicle that the decal or sticker like the traffic sign is pasted on is existed in front of your vehicle, or when you overtake such a vehicle, -When the traffic sign is in front of the vehicle on the roundabout,
OPERATING YOUR VEHICLE
NOTE: The traffic sign may be continued to dis­play on the information display under the following situations. Drive safely accord­ing to the actual traffic rules. -When you drive in the area where the different speed limit is established even though there is no speed limit sign, -When you drive in the area where the end of traffic regulation is indicated by the lane on the road even though there is no traffic sign to indicate the end of the traffic regulation,
Situations where the dual sensor can­not be detected accurately by the posi­tions or conditions of the traffic signs The detection of traffic sign may be done with delay or there may be a possibility to occur no detection or inaccurate detection of the traffic sign including the supplemen­tal mark under the following situations. When the traffic sign is dirt and hidden by the leaves of the tree or the vehicle in front of your vehicle and then it is hard to recognize the traffic sign, When the circumstance of the traffic sign is complicated and it is hard to recognize the traffic sign, When the traffic sign is far from the vehi­cle, When the traffic sign is bended or
deformed, When the color of the traffic sign is
faded,
3-42

OPERATING YOUR VEHICLE
When the direction of traffic sign is Handling dual sensor changed, • When the traffic sign is damaged, • When the traffic sign is aimed diagonally to the vehicle, When the signboard, the poster or traffic information signboard is installed on the top or bottom of it, When the object as mud, snow or the ice is attached on the traffic sign, • When there is a traffic sign on a corner or a curve, When there is a traffic sign where light of the headlight is hard to reach, When the traffic sign is hard to recognize due to the illumination on the roads or the shadow of the building,
When the size of the traffic sign is small, (1) Dual sensor When the traffic sign is a lighting type, When the traffic sign is assimilated into the building on the background and it is hard to recognize the traffic sign, When there is a hidden or rubbed part on the traffic sign and the traffic sign is hard to recognize, When the traffic sign is refiected by the strong light (for example, backlight or headlight) and the dual sensor cannot detect accurately,
NOTE: There may be a possibility to detect the supplemental mark inaccurately or not to detect it as the traffic sign by the situations around the vehicle.
3-43
78RB03012
A WARNING
The detection performance of the dual sensor has limits and the dual sensor cannot detect all vehicles, pedestrian, object of the high beam assist (such as the lights of the vehi­cle in front of you, street lamps, etc.), partition lines or traffic sign. Do not rely excessively on the system and always drive in a safe manner. • Observe the following instructions in order to keep the dual sensor functioning properly. If mishandled, the dual sensor cannot accurately detect a vehicle, a pedestrian, an object of the high beam assist (such as the lights of the vehicle in front of you, street lamps, etc.) or partition lines in front of you, the system will not function properly and unexpected accidents may occur. -Do not touch the lens of the dual sensor. -Do not clean the lens of the dual sensor by yourself. -Do not strike the body of, or any surrounding parts of the dual sensor. (Continued)

A WARNING
(Continued) -Do not remove or disassemble the dual sensor. -Do not stick or affix anything to the lens of the dual sensor, not even clear items. • When the windshield around the dual sensor is deformed or dam­aged, or the windshield in front of the dual sensor is cracked because of an accident, the dual sensor can­not detect an obstacle in front of you, a pedestrian, an object of the high beam assist (such as the lights of the vehicle in front of you, street lamps, etc.), partition lines or traffic signs properly. If driving with these damaged parts, the dual sen­sor brake support will not function properly and unexpected accidents may occur. Operate the dual sensor brake support OFF switch to turn off the dual sensor brake support, and ask a SUZUKI dealer to have them inspected. (Continued)
A WARNING
(Continued) Do not apply any accessories (other than SUZUKI genuine acces­sories), films or stickers to the area listed below. These may affect with visibility of the dual sensor. If the area of the dual sensor is obstructed, the dual sensor cannot detect any vehicles, pedestrians, objects of the high beam assist (such as the lights of the vehicle in front of you, street lamps, etc.), partition lines or traffic signs prop­erly and the dual sensor brake sup­port may not function properly. Also, if applying them to an area other than the prohibited area, it may affect with the function of the dual sensor by reflection of light or an image. In this case, move them to another place. -On windshield
OPERATING YOUR VEHICLE
A WARNING
Do not remove or disassemble laser sensor parts of dual sensor. Do not look into irradiation portion of dual sensor by using the optical instrument such as magnifying glass, the objective glass, etc at distance within 10 cm (3.9 inch) from dual sensor when the ignition switch is turned to "ON". Your eyes might be damaged by laser.
3-44

OPERATING YOUR VEHICLE
Laser explanatory label
Max overage power: 45 mW Pulse duration: 33 ns Wavelength: 905 nm
IEC 60825-1 :2007 Complies with FDA performance standards for laser products except for deviations pursuant to Laser Notice No. 50, dated Ju!y 26'", 2001
52RM30510
Laser emission data Maximum average power: 45 mW Pulse duration: 33 ns Wave length: 905 nm Divergence (horizontal x vertical): 28' x 12'
NOTE: The detection of the vehicle and an obsta­cle in front of you, partition lines ·on the road by the dual sensor is limited within the visual range. It also takes several seconds to detect and activate the alert after an object is appeared in the visual range of the dual sensor.
3-45
Laser classification label
INVISIBLE LASER RADIATION DO NOT VIEW DIRECTLY WITH OPTICAL INSTRUMENTS (MAGNIFIERS) CLASS 1M LASER PRODUCT
52RM30520
A WARNING
Do not stick a sticker or a film (including transparent thing) on the front of dual sensor of the outside windshield as shown in the below illustration.
78RB03013
(1) (2) Prohibited area
The prohibited area (1) and (2) are shown as below. (1) From top edge of windshield to dual sensor approximately 10 cm (3.9 inch) below of the bottom end of dual sensor (2) Approximately 20 cm (7.8 inch) from the center of dual sensor to right and left approximately 10 cm (3.9 inch)
A WARNING
Do not stick a sticker or a film (including transparent thing) below the dual sensor camera inside the windshield shown as following illus­tration.

When there is a large temperature gap between inside of the vehicle and outside air (such as winter), windshield is easy to fog. If the front portion of dual sensor on the windshield is fogged up or covered with condensation or ice, dual sensor brake support may not activate temporar­ily. In this case, use the front defroster to remove the fog, etc.
When cleaning inside of the windshield, do not adhere the glass cleaner to lens.
OPERATING YOUR VEHICLE
3-46

OPERATING YOUR VEHICLE
Temporary stop or failure of the dual sensor The following chart shows the temporary stop or failure of the dual sensor.
(1)
(2)
(3)
(4)
3-47
ra
!~ I ,. I
®
...
FUNCTION TEMPORARILY DISABLED
(#1)
.~
SYSTEM WARNING
Dual sensor
Temporary
Stop
On
Off
On
On
On
Failure
Off
On
(1) Dual sensor brake support indicator light (2) Lane departure warning indicator light (3) High beam assist warning light (orange) (4) Indication of information display
#1: Depending on the cause of the tem­porary stop or failure, the following message may appear simultaneously.
.~ FUNCTION TEMPORARILY DISABLED (CAM VIS)
.~ FUNCTION TEMPORARILY DISABLED (CAM TEMP)
75RM350

NOTE: When the function of the dual sensor is temporarily stopped or malfunctioning, all of following functions will be turned off. Dual sensor brake support Lane departure warning Vehicle swaying warning High beam assist Traffic sign recognition
Temporary stop of the dual sensor Under the following situations, the function of the dual sensor stops temporarily. When the situations are improved, the temporary stop of the function will be can­celed. When the visibility of the dual sensor is poor Refer to "Situations where the dual sen­sor may not activate properly" in this section for details. When the temperature of the body of dual sensor is high When the systems related to the dual sensor brake support are stopped tem­porarily When the battery has a voltage abnor­mality
Failure of the dual sensor When the dual sensor is faulty, the function of the dual sensor is stopped until the igni­tion switch is turned to "LOCK". Find a safe place to park and turn the igni­tion switch to "LOCK". Restart the engine, and check that the dual sensor brake support indicator light, lane departure warning indicator light, and high beam assist warning light go off. If all of the indicators stay on after restarting the engine, there may be a failure of the dual sensor. Ask a SUZUKI dealer to have the dual sensor inspected.
NOTE: Under the following situations, the dual sensor brake support indicator light, lane departure warning indicator light, and high beam assist warning light come on after the engine has been started, it does not indicate a malfunction. Once the ignition switch to is turned to "LOCK" position and then the engine is restarted, these indicators will go off. -When the automatic brake system has been operating 3 times -When the automatic brake system has been operating for long periods
OPERATING YOUR VEHICLE
The function of the dual sensor is stopped if the dual sensor brake support indicator light, lane departure warning indicator light, and high beam assist warning light come on and there may be a failure of the dual sensor, but it r}oes not hinder normal driving.
Pedestrian detection The dual sensor detects pedestrians by whose size, shape or motion.
•
•
T
(1)
75RM238
(1) About 1 -2 m (3.3 -6.6 ft)
3-48