seat SUZUKI JIMNY 2022 Manual PDF

Front door pocket (4)
78RB05068
This pocket is provided for holding light and soft things such as gloves, newspa­pers or magazines.
A CAUTION
Do not put hard or breakable objects in the pocket. If an accident occurs, objects such as bottles, cans, etc. can injure the occupants in the door pocket.
OTHER CONTROLS AND EQUIPMENT
Luggage box (5) (if equipped)
(1)
78RB05021
The luggage box (1) is equipped in the lug­gage compartment. You can place lug­gage or other cargos under the board.
NOTICE
If the rear seatback is raised with heavy objects on the flap (2) of the luggage box, the luggage box may be damaged. Remove heavy objects before raising the rear seatback.
5-12

INSPECTION AND MAINTENANCE
60B128S
.A. WARNING
Take extreme care when working on· your vehicle to prevent accidental injury. Carefully observe the follow­ing precautions: • To prevent damage or unintended activation of the airbag system or seat belt pretensioner system, check that the lead-acid battery is discon­nected and the ignition switch has been in "LOCK" position for at least 90 seconds before performing any electrical service work on your SUZUKI vehicle. Do not touch airbag system components, seat belt pre­tensioner system components or wires. The wires are wrapped with yellow tape or yellow tubing, and the cou­plers are yellow for easy identifica­tion. Do not leave the engine running in garages or other confined areas. (Continued)
6-1
.A. WARNING
(Continued) When the engine is running, keep hands, clothing, tools, and other objects away from the fan and drive belt. Even though the fan may not be moving, it can automatically turn on without warning . • When it is necessary to perform service work with the engine run~ ning, check that the parking brake is set fully and the transmission is in Neutral (for manual transmission vehicles) or Park (for automatic transmission vehicles). Do not touch ignition wires or other ignition system parts when starting the engine or when the engine is running, or you could receive an electric shock. • Be careful not to touch a hot engine, exhaust manifold and pipes, muffler, radiator and water hoses. Do not allow smoking, sparks, or flames around fuel or the battery. Flammable fumes are present. Do not get under your vehicle if it is supported only with the portable jack provided in your vehicle. • Be careful not to cause accidental short circuits between the positive and negative battery terminals. (Continued)
.A. WARNING
(Continued) Keep used oil, coolant, and other fluids away from children and pets. Dispose of used fluids properly; never pour them on the ground, into sewers, etc.

INSPECTION AND MAINTENANCE
Oil filler replacement
1) Using an oil filter wrench, turn the oil fil­ter counterclockwise and remove ii. 2) Using a clean rag, wipe off the mount­ing surface on the engine where the new filter will be seated. 3) Smear a small amount of engine oil around the rubber gasket of the new oil filter. 4) Screw the new filter by hand until the fil­ter gasket contacts the mounting sur­face.
(1) Loosen (2) Tighten
6-27

54G092
Tightening (viewed from filter top)
(1)
(1) Oil filter (2) 3/4 turn
NOTICE
(2)
54G093
To tighten the oil filter properly, it is important to accurately identify the position at which the filter gasket first contacts the mounting surface.
5) Tighten the filter as specified below from the point of contact with the mounting surface (or to the specified torque) using an oil filter wrench.
Tightening torque for oil filter: 3/4 turn or 14 Nm (1.4 kg-m, 10.3 lb-ft)
NOTICE
To prevent oil leakage, check that the oil filter is tight, but do not over­tighten it.

6) Install the new wheel and replace the wheel nuts with their cone shaped end facing the wheel. Tighten each nut snugly by hand until the wheel is securely seated on the hub.
78RB07017
Tightening torque for wheel nut: 100 Nm (10.0 kg-m, 72.3 lb-ft)
7) Lower the jack and fully tighten the nuts in a crisscross fashion with a wrench as shown in the illustration.
A WARNING
Use genuine wheel nuts and tighten them to the specified torque as soon as possible after changing wheels. Incorrect wheel nuts or improperly tightened wheel nuts may come loose or fall off, which can result in an accident. If you do not have a torque wrench, have the wheel nut torque checked by a SUZUKI dealer.
INSPECTION AND MAINTENANCE
NOTE: How to install the spare wheel:
(3)
78RB07053
When you install a 195/B0R 15 spare wheel to the vehicle, set the spare tyre bracket (3) (if equipped) with the mark of "195" on up posi­tion, and handle it in the reverse order of removal. For vehicles equipped with the spare wheel half cover; when you install the spare wheel half cover, check that the hollow (4) of the cover is positioned below the center of the spare wheel half cover.
6-40

INSPECTION AND MAINTENANCE
Fuses under dashboard
6-45
78RB07024
1 2 3 4 5 6 7 8 9 10 11 12
71819202122232425
80P0185
PRIMARY FUSE
(1) 30A Power window
(2) 10A Meter
(3) 15A Engine Control Module
(4) 5A lgnition-1 signal 2
(5) 20A Blank
(6) -Blank
(7) -Blank
(8) 20A Door lock
(9) 15A Steering lock
(10) 10A Hazard
(11) -Blank
(12) 10A Rear fog lamp
(13) 5A ABS/Esp® control mod-ule
(14) 15A Seat heater
(15) 5A lgnition-1 signal 3
(16) 10A Dome light-2
(17) 5A Dome light
(18) 15A Radio
(19) 5A CONT
(20) 5A Key2
(21) 20A Power window timer
(22) 5A Key
(23) 15A Horn
(24) 5A Tail light (Left)
(25) 10A Tail light
(26) 10A Airbag
(27) 10A lgnition-1 signal
(28) 10A Back-up light
(29) 5A ACC-3
(30) 20A Rear defogger
(31) 10A Heated mirror
(32) 15A ACC-2
(33) 5A ACC
(34) 10A Rear wiper
(35) 5A lgnition-2 signal
(36) 15A Washer
(37) 25A Front wiper
(38) 10A Stop light

NOTICE
Never apply a garage jack to the exhaust pipe, front fender splash guard, side sill splash, rear fender splash guard, front differential or rear differential.
NOTE: For more details, contact a SUZUKI dealer.
Changing wheels
To change a wheel, use the following pro­
cedure: 1) Prepare the jack, tools and spare tyre. 2) Loosen, but do not remove the wheel nuts. 3) Jack up the vehicle (follow the jacking instructions in this section).
A WARNING
Shift into "P" (Park) for an automatic transmission, or into 11R" (Reverse) for a manual transmission vehicle when you jack up the vehicle. Never jack up the vehicle with the transmission in "N" (Neutral). OthR erwise, unstable jack may cause an accident.
4) Remove the wheel nuts and wheel.
65J4033
5) Clean any mud or dirt off from the sur­face of the wheel (1 ), hub (2), thread part (3) and surface of the wheel nuts (4) with a clean cloth. Clean the hub carefully; it may be hot from driving.
EMERGENCY SERVICE
6) Install the new wheel and replace the wheel nuts with their cone shaped end facing the wheel. Tighten each nut snugly by hand until the wheel is securely seated on the hub.
78RB08003
Tightening torque for wheel nut 100 Nm (10.0 kg-m, 72.3 lb-ft)
7) Lower the jack and fully tighten the nuts with a wheel wrench in numerical order as shown in the illustration.
7-4

APPEARANCE CARE
Cleaning interior
Vinyl upholstery Prepare a solution of soap or mild deter­gent dissolved in warm water. Apply the solution to the vinyl with a sponge or soft cloth and let it soak for a few minutes to loosen dirt. · Rub the surface with a clean, damp cloth to remove dirt and the soap solution. If some dirt still remains on the surface, repeat this procedure.
Fabric upholstery Remove loose dirt with a vacuum cleaner. Using a mild soap solution, rub stained areas with a clean damp cloth. To remove soap, rub the areas again with a cloth dampened with water. Repeat this until the stain is removed, or use a commercial fab­ric cleaner for tougher stains. If you use a fabric cleaner, carefully follow the manu­facturer's instructions and precautions.
Leather upholstery Remove loose dirt with a vacuum cleaner. Using a mild soap or saddle soap solution, wipe dirt off with a clean damp soft cloth. To remove soap, wipe the areas again with a soft cloth dampened with water. Wipe the areas dry with a soft dry cloth. Repeat this until the dirt or stain is removed, or use a commercial leather cleaner for tougher dirt or stains. If you use a leather cleaner, carefully follow the manufacturer's instruc­tions and precautions. Do not use solvent type cleaners or abrasive cleaners.
NOTE: In order to keep leather upholstery look­ing good, it should be cleaned at least twice a year. If leather upholstery becomes wet, immediately wipe it dry with tissue paper or a soft cloth. Water may cause leather to harden and shrink if it is not wiped off. When parking on sunny days, select a shady place or use a sunshade. If leather upholstery is exposed to direct sunlight for a long time, it may disco/or and shrink. As is common with natural materials, leather is inherently irregular in grain and cowhide has spots in its natural state. These do not affect the performance of the leather in any way.
Seat belts Clean seat belts with a mild soap and water. Do not use bleach or dye on the belts. They may weaken the fabric in the belts.
Vinyl floor mats Ordinary dirt can be removed from vinyl with water or mild soap. Use a brush to help loosen dirt. After the dirt is loosened, rinse the mat thoroughly wtth water and dry it in the shade.
Carpets Remove dirt and soil as much as possible with a vacuum cleaner. Using a mild soap solution, rub stained areas with a clean damp cloth. To remove soap, rub the areas again with a cloth dampened with water. Repeat this until the stain is removed, or use a commercial carpet cleaner for tougher stains. If you use a carpet cleaner, carefully follow the manufacturer's instruc­tions and precautions.
Instrument panel and console Remove loose dirt with a vacuum cleaner. Gently wipe dirt off with a tightly squeezed damp clean cloth. Repeat this until the dirt is removed.

SUPPLEMENT
For Australia
Built date
Built date is located on Vehicle Identifica­tion plate. "Built date" means -the calendar month and the year in which the body shell and power train sub-assemblies are conjoined and the vehicle is driven or moved from the production line.
Child restraint
A WARNING
Child restraint anchorages are designed to withstand only those loads imposed by correctly fitted child restraints. Under no circum­stances are they to be used for adult seat belts, harnesses or for attaching other items or equipment to the vehi­cle.
10-1
Installation of child restraint with
top tether anchorage
Some child restraint systems require the use of a top tether strap. Top tether anchorage brackets are provided in your vehicle at the locations shown in the illus­tration. The number of the top tether anchorage brackets provided in your vehi­cle depends on the vehicle specification.
(1)
(1) Anchor fitting
78RB10005
1) Remove the luggage box (1 ). 2) Secure the child restraint on the rear seat using the procedure described above for securing a restraint system that does not require a top tether strap. 3) Hook the top tether strap to the top tether anchorage bracket and tighten the top tether strap according to the instructions provided by the child restraint system manufacturer. Attach 54Gm the top tether strap to the correspond­ing top tether anchorage bracket located on the floor of the rear cargo area.

4) When routing the top tether strap, pass the top tether strap as shown in the illustration. (Refer to "Head restraints" section for details on how to adjust the height of head restraint or remove it.) 5) Check that cargo does not interfere with routing of the top tether strap.
NOTICE
When installing a child restraint sys­tem to the rear seat, adjust the front seat position so that the front seat does not interfere with the child restraint system.
SUPPLEMENT
Rear-facing child restraint
58MS030
A WARNING
Do not use a rearward facing child restraint on a seat protected by an airbag in front of it.
A WARNING
Do not install a rear-facing child restraint in the front passenger's seat. If the passenger's front airbag inflates, a child in a rear-facing child restraint could be killed or severely injured. The back of a rear-facing child restraint would be too close to the inflating airbag.
10-2

SUPPLEMENT
If you must use a front-facing child restraint in the front passenger's seat, be sure to move the front passenger's seat as far back as possible. Please refer to "Seat belts and child restraint systems" in the "BEFORE DRIVING" section for details on securing your child.
Airbag symbol meaning
A (ill
AIRBAG ~
®
@~
72M00150
You may find this label on the sun visor.
A WARNING
NEVER use a rearward facing child restraint on a seat protected by an ACTIVE AIRBAG in front of it, DEATH or SERIOUS INJURY to the CHILD can occur.
10-3
Seat belt warning
Follow this warning as well as the instruc­tion for seat belt in this book.
A WARNING
Seat belts are designed to bear upon the bony structure of the body, and should be worn low across the front of the pelvis or the pelvis, chest and shoulders, as applicable; wearing the lap section of the belt across the abdominal area must be avoided. • Seat belts should be adjusted as firmly as possible, consistent with comfort, to provide the protection for which they have been designed. A slack belt will greatly reduce the protection afforded to the wearer. • Care should be taken to avoid con­tamination of the webbing with pol­ishes, oils and chemicals, and particularly battery acid. Cleaning may safely be carried out using mild soap and water. The belt should be replaced if webbing becomes frayed, contaminated or damaged. (Continued)
A WARNING
(Continued) • It is essential to replace the entire assembly after it has been worn in a severe impact even if damage to the assembly is not obvious. Belts should not be worn with straps twisted. Each belt assembly must only be used by one occupant; it is danger­ous to put a belt around a child being carried on the occupant's lap,
In the case where a "Seat Belt Assembly'' incorporates an "Automatic Length Adjust­ing and Locking Retractor' or an "Emer­gency Locking Retractor'.
A WARNING
No modifications or additions should be made by the user which will either prevent the seat belt adjusting devices from operating to remove slack, or prevent the seat belt assembly from being adjusted to remove slack. Referring to the SEAT BELT instruction in this book, adjust the seat belt so that the lap and sash portions of the Seat Belt Assembly fit as firmly as possible consistent with comfort.