Crank SUZUKI SWIFT 2000 1.G SF310 Service User Guide

6-12 ENGINE GENERAL INFORMATION AND DIAGNOSIS (TBI FOR G10)
CUSTOMER PROBLEM INSPECTION FORM (EXAMPLE)
User name:Model:VIN:
Date of issue:Date Reg.Date of problem:Mileage:
PROBLEM SYMPTOMS
Difficult Starting
No cranking
No initial combustion
No combustion
Poor starting at
(cold warm always)
OtherPoor Driveability
Hesitation on acceleration
Back fire /After fire
Lack of power
Surging
abnormal knocking
Other
Poor Idling
Poor fast idle
Abnormal idling speed
(High Low) ( r / min.)
Unstable
Hunting ( r / min. to r / min.)
OtherEngine Stall when
Immediately after start
Accel. pedal is depressed
Accel. pedal is released
Load is applied
A/C Electric load P/S
Other
Other
OTHERS:
VEHICLE / ENVIRONMENTAL CONDITION WHEN PROBLEM OCCURS
Environmental Condition
Weather
Temperature
Frequency
RoadFair Cloudy Rain Snow Always Other
Hot Warm Cool Cold (F/C) Always
Always Sometimes ( times/ day, month) Only once Under certain condition
Urban Suburb Highway Mountainous (Uphill Downhill) Tarmacadam Gravel
Other
Vehicle Condition
Engine
conditionCold Warming up phase Warmed up Always Other at starting
Immediately after start Racing without load Engine speed ( r / min.)
Vehicle
conditionDuring driving: Constant speed Accelerating Decelerating
Right hand corner Left hand corner When shifting (Lever position ) At stop
Vehicle speed when problem occurs ( km/h, Mile / h) Other
Malfunction indicator
lamp conditionAlways ON Sometimes ON Always OFF Good condition
Diagnostic troubleFirst check:No code Malfunction code ( )g
codeSecond check:No code Malfunction code ( )
NOTE:
The above form is a standard sample. It should be modified according to conditions characteristic of each
market.

6-16 ENGINE GENERAL INFORMATION AND DIAGNOSIS (TBI FOR G10)
DTC
NO.DETECTING ITEMDETECTING CONDITION
(DTC will set when detecting:)MIL
P0335Crankshaft position sensor
circuit malfunctionNo signal during engine running1 driving cycle
P0340Camshaft position sensor
circuit malfunctionNo signal for 2 sec. during engine cranking1 driving cycle
P0420Catalyst system efficiency
below threshold
Output waveforms of HO2S-1 and HO2S-2
are similar.
(Time from output voltage change of HO2S-1
to that of HO2S-2 is shorter than
specification.)
2 driving cycles
P0443EVAP Purge control valve
circuit malfunctionPurge control valve circuit is open or shorted
to ground2 driving cycles
P0480Radiator fan control circuit
malfunctionRadiator cooling fan relay terminal voltage is
low when cooling temp. is lower than
specification
2 driving cycles
P0500Vehicle speed sensor
malfunctionNo signal while running in “D” range or during
fuel cut at decelerating2 driving cycles
P0505Idle control system malfunction
Throttle opening change is small as compared
with electrically live time. Throttle valve opening
is not within its target range with CTP switch ON
or drive voltage exists though ECM (PCM) is not
outputting ISC drive command.
1 driving cycle
P0510Closed throttle position switch
malfunctionSwitch does not change from ON to OFF
(or from OFF to ON) even when vehicle speed
reaches over (or below) specification.
2 driving cycle
P1250Early Fuel Evaporation Heater
Circuit MalfunctionHeater monitor terminal voltage is higher than
specified value when EFE OFF or it is lower
than specified value when EFE ON.
2 driving cycles
P1450Barometric pressure sensor
circuit malfunctionBarometric pressure is lower or higher than
specification. (or sensor malfunction)1 driving cycle
P1451Barometric pressure sensor
performance problem
Difference between manifold absolute
pressure (MAP sensor value) and
barometric pressure (barometric pressure
sensor value) is larger than specification
during cranking.
2 driving cycles
P1500Starter signal circuit
malfunctionStarter signal is not inputted from engine
cranking till its start and after or it is always
inputted
2 driving cycles
P1510ECM (PCM) backup power
source malfunctionNo backup power after starting engine1 driving cycle

6-20 ENGINE GENERAL INFORMATION AND DIAGNOSIS (TBI FOR G10)
ENGINE BASIC INSPECTION
This check is very important for troubleshooting when ECM (PCM) has detected no DTC and no abnormality has
been found in visual inspection.
Follow the flow table carefully.
STEP
ACTIONYESNO
1Was “ENGINE DIAG. FLOW TABLE” performed?Go to Step 2.Go to “ENGINE DIAG.
FLOW TABLE”.
2Check battery voltage.
Is it 11 V or more?Go to Step 3.Charge or replace
battery.
3Is engine cranked?Go to Step 4.Go to “DIAGNOSIS”
in Section 6G.
4Does engine start?Go to Step 5.Go to Step 7.
5Check idle speed as follows.
1) Warm up engine to normal operating temp.
2) Shift transmission to neutral position for M / T
(“P” position for A / T).
3) All of electrical loads are switched off.
4) Check engine idle speed with scan tool.
See Fig. 1.
Is it 800 – 900 r / min.?Go to Step 6.Go to “ENGINE
DIAGNOSIS TABLE”.
6Check ignition timing as follows.
1) Select “MISC” mode on SUZUKI scan tool and
fix ignition timing to initial one. See Fig. 2.
2) Using timing light (1), check initial ignition timing.
See Fig. 3.
Is it 5 ± 3 BTDC at specified idle speed?Go to “ENGINE
DIAGNOSIS TABLE”.Check ignition control
related parts referring
to Section 6F.
7Check immobilizer system malfunction as follows.
1) Check immobilizer indicator lamp for flashing.
Is it flashing when ignition switch is turned to ON
position?Go to “DIAGNOSIS” in
Section 8A.Go to Step 8.
8Check fuel supply as follows.
1) Check to make sure that enough fuel is filled in fuel
tank.
2) Turn ON ignition switch for 2 seconds and then
OFF. See Fig. 4.
Is fuel return pressure (returning sounds) felt from fuel
feed hose (1) when ignition switch is turned ON?Go to Step 10.Go to Step 9.
9Check fuel pump for operating.
1) Was fuel pump operating sound heard from fuel
filler for about 2 seconds after ignition switch ON
and stop?Go to “DIAG. FLOW
TABLE B-3”.Go to “DIAG. FLOW
TABLE B-2”.
10Check ignition spark as follows.
1) Disconnect injector coupler.
2) Remove spark plugs and connect them to high
tension cords.
3) Ground spark plugs.
4) Crank engine and check if each spark plug sparks.
Is it in good condition?Go to Step 11.Go to “DIAGNOSIS”
in Section 6F.
11Check fuel injector for operation as follows.
1) Install spark plugs and connect injector
connectors.
2) Check that fuel is injected out in conical shape
from fuel injector when cranking.
Is it in good condition?Go to “ENGINE
DIAGNOSIS TABLE”.Go to “DIAG. FLOW
TABLE B-1”.

6-22 ENGINE GENERAL INFORMATION AND DIAGNOSIS (TBI FOR G10)
ENGINE DIAGNOSIS TABLE
Perform troubleshooting referring to following table when ECM (PCM) has detected no DTC and no abnormality
has been found in visual inspection and engine basic inspection previously.
Condition
Possible CauseReferring Item
Hard Starting
(Engine cranks OK)Ignition system out of order

Faulty spark plug

Leaky high-tension cord

Loose connection or disconnection of high-
tension cords or lead wires

Faulty ignition coil
Fuel system out of order

Dirty or clogged fuel hose or pipe

Malfunctioning fuel pump

Air inhaling from intake manifold gasket or
throttle body gasket

Fuel injector resistor malfunction
Engine and emission control system out of
order

Faulty idle control system

Faulty ECT sensor or MAP sensor

Faulty ECM (PCM)
Low compression

Poor spark plug tightening or faulty gasket

Compression leak from valve seat

Sticky valve stem

Weak or damaged valve springs

Compression leak at cylinder head gasket

Sticking or damaged piston ring

Worn piston, ring or cylinder
Others

Malfunctioning PCV valve
Spark plugs in Section 6F
High-tension cords in Section 6F
High-tension cords in Section 6F
Ignition coil in Section 6F
Diagnostic Flow Table B-3
Diagnostic Flow Table B-3
Fuel injector resistor in Section 6E1
Diagnostic Flow Table P0505
ECT sensor or MAP sensor in
Section 6E1
Compression check in Section
6A
Spark plugs in Section 6F
Valves inspection in Section 6A
Valves inspection in Section 6A
Valve springs inspection in
Section 6A
Cylinder head inspection in
Section 6A
Cylinders, pistons and piston rings
inspection in Section 6A
Cylinders, pistons and piston rings
inspection in Section 6A
PCV system in Section 6E1

ENGINE GENERAL INFORMATION AND DIAGNOSIS (TBI FOR G10) 6-23
ConditionPossible CauseReferring Item
Low oil pressure
Improper oil viscosity

Malfunctioning oil pressure switch

Clogged oil strainer

Functional deterioration of oil pump

Worn oil pump relief valve

Excessive clearance in various sliding partsEngine oil and oil filter change in
Section 0B
Oil pressure switch inspection in
Section 8
Oil pan and oil pump strainer
cleaning in Section 6A
Oil pump in Section 6A
Oil pump in Section 6A
Engine noise
Note: Before
checking mechanical
noise, make sure
that:

Specified spark
plug in used.

Specified fuel is
used.Valve noise

Improper valve lash

Worn valve stem and guide

Weak or broken valve spring

Warped or bent valve
Piston, ring and cylinder noise

Worn piston, ring and cylinder bore
Connecting rod noise

Worn rod bearing

Worn crank pin

Loose connecting rod nuts

Low oil pressure
Crankshaft noise

Low oil pressure

Worn bearing

Worn crankshaft journal

Loose bearing cap bolts

Excessive crankshaft thrust play
Valve lash in Section 6A
Valves inspection in Section 6A
Valve springs inspection in
Section 6A
Valves inspection in Section 6A
Pistons and cylinders inspection
in Section 6A
Crank pin and connecting rod
bearing inspection in Section 6A
Crank pin and connecting rod
bearing inspection in Section 6A
Connecting rod installation in
Section 6A
Previously outlined
Previously outlined
Crankshaft and bearing
inspection in Section 6A
Crankshaft and bearing
inspection in Section 6A
Crankshaft inspection in
Section 6A
Crankshaft thrust play inspection
in Section 6A

6-32 ENGINE GENERAL INFORMATION AND DIAGNOSIS (TBI FOR G10)
SCAN TOOL DATA DEFINITIONS
FUEL SYSTEM (FUEL SYSTEM STATUS)
Air / fuel ratio feedback loop status displayed as either
open or closed loop. Open indicates that ECM (PCM)
ignores feedback from the exhaust oxygen sensor.
Closed indicates final injection duration is corrected
for oxygen sensor feedback.
CALC LOAD (CALCULATED LOAD VALUE, %)
Engine load displayed as a percentage of maximum
possible load. Value is calculated mathematically us-
ing the formula: actual (current) intake air volume

maximum possible intake air volume x 100%.
COOLANT TEMP.
(ENGINE COOLANT TEMPERATURE, C, F)
It is detected by engine coolant temp. sensor
SHORT FT B1 (SHORT TERM FUEL TRIM, %)
Short term fuel trim value represents short term
corrections to the air / fuel mixture computation. A val-
ue of 0 indicates no correction, a value greater than
0 means an enrichment correction, and a value less
than 0 implies an enleanment correction.
LONG FT B1 (LONG TERM FUEL TRIM, %)
Long term fuel trim Value represents long term correc-
tions to the air / fuel mixture computation. A value of 0
indicates no correction, a value greater than 0 means
an enrichment correction, and a value less than 0 im-
plies an enleanment correction.
MAP (INTAKE MANIFOLD ABSOLUTE
PRESSURE, kPa, inHg)
It is detected by manifold absolute pressure sensor and
used (among other things) to compute engine load.
ENGINE SPEED (rpm)
It is computed by reference pulses from crankshaft
position sensor.
VEHICLE SPEED (km / h, MPH)
It is computed based on pulse signals from vehicle
speed sensor.
IGNITION ADVANCE
(IGNITION TIMING ADVANCE FOR NO.1
CYLINDER, )
Ignition timing of NO.1 cylinder is commanded by
ECM (PCM). The actual ignition timing should be
checked by using the timing light.
INTAKE AIR TEMP. (C, F)
It is detected by intake air temp. sensor and used to
determine the amount of air passing into the intake
manifold as air density varies with temperature.
MAF (MASS AIR FLOW RATE, gm / s, lb / min)
It represents total mass of air entering intake manifold
which is computed based on signals from MAP sen-
sor, IAT sensor, TP sensor, etc.
THROTTLE POS
(ABSOLUTE THROTTLE POSITION, %)
When throttle position sensor is fully closed position,
throttle opening is indicated as 0% and 100% full open
position.
OXYGEN SENSOR B1 S1
(HEATED OXYGEN SENSOR-1, V)
It indicates output voltage of HO2S-1 installed on ex-
haust manifold (pre-catalyst).
OXYGEN SENSOR B1 S2
(HEATED OXYGEN SENSOR-2, V)
It indicates output voltage of HO2S-2 installed on ex-
haust pipe (post-catalyst). It is used to detect catalyst
deterioration.
DESIRED IDLE (DESIRED IDLE SPEED, rpm)
The Desired Idle Speed is an ECM (PCM) internal pa-
rameter which indicates the ECM (PCM) requested
idle. If the engine is not running, this number is not valid.
TP SENSOR VOLT (THROTTLE POSITION
SENSOR OUTPUT VOLTAGE, V)
The Throttle Position Sensor reading provides throttle
valve opening information in the form of voltage.
INJ PULSE WIDTH
(FUEL INJECTION PULSE WIDTH, msec.)
This parameter indicates time of the injector drive
(valve opening) pulse which is output from ECM
(PCM) (but injector drive time of NO.1 cylinder for
multiport fuel injection).
IAC FLOW DUTY (IDLE AIR (SPEED) CONTROL
DUTY, %)
This parameter indicates opening of the throttle valve
in terms of percentage to opening controllable by the
ISC actuator.
TOTAL FUEL TRIM (%)
The value of Total Fuel Trim is obtained by putting val-
ues of short Term Fuel Trim and Long Term Fuel Trim
together. This value indicates how much correction is
necessary to keep the air / fuel mixture stoichiomet-
rical.
BATTERY VOLTAGE (V)
This parameter indicates battery positive voltage in-
putted from main relay to ECM (PCM).

6-36 ENGINE GENERAL INFORMATION AND DIAGNOSIS (TBI FOR G10)
CONNECTOR “C01”
TER-
MINALWIRE
COLORCIRCUITSTANDARD
VOLTAGECONDITION
1LgPower source for sensor4.75 – 5.25 VIgnition switch ON
2OrCamshaft position sensor (+)——
3W/BCrankshaft position sensor
(+)——
4Gr / GClosed throttle position switch
0 – 1 V
Ignition switch ON, ISC actuator
plunger is in contact with throttle lever
screw
4Gr / G(In ISC actuator)
4 – 6 V
Ignition switch ON
Plunger is apart from throttle lever
screw
5Lg / RManifold absolute pressure
sensor3.3 – 4.0 V
Ignition switch ON
Barometric pressure: 100 kPa,
760 mmHg
6Lg / WThrottle position sensor
0.2 – 1.0 V
Ignition switch ON, when clearance
between throttle lever and throttle stop
screw is less than 0.35 mm (0.014 in.)
2.8 – 4.8 VIgnition switch ON
Throttle valve at full open position
7Gr / WEngine coolant temp. sensor0.55 – 0.95 VIgnition switch ON
Engine coolant temp.: 80C (176F)
8P/BHeater of H02S-110 – 14 VIgnition switch ON
9GGround for sensors——
10WCamshaft position sensor (–)——
11W/RCrankshaft position sensor
(+)——
12W/BEFE heater monitor0 – 1 VHeater relay OFF12W/BEFE heater monitor10 – 14 VHeater relay ON
13RHeated oxygen sensor-1Refer to DTC flow chart
14GrIntake air temp. sensor2.0 – 2.7 V
Ignition switch ON
Sensor ambient temp.
(Intake air temp): 20C (68F)
10 – 14 VIgnition switch ON
15Bl / WPower steering pressure
switch (If equipped)
0 – 1 V
With engine running at idle speed,
turning steering wheel to the right or left
as far as it stops, repeating it a few
times
16B/YEngine start switch6 – 12 VWhile engine cranking16B/Yg
(Engine start signal)0 – 1 VOther than above

6-40 ENGINE GENERAL INFORMATION AND DIAGNOSIS (TBI FOR G10)
“IG COIL METER”Main relay
Ignition switch
In fuseMalfunction indicator lamp in combination meter
TABLE A-1 MALFUNCTION INDICATOR LAMP CIRCUIT CHECK – LAMP DOES
NOT COME “ON” AT IGNITION SWITCH ON (BUT ENGINE AT STOP)
CIRCUIT DESCRIPTION
When the ignition switch is turned ON, ECM (PCM) causes the main relay to turn ON (close the contact point).
Then, ECM (PCM) being supplied with the main power, turns ON the malfunction indicator lamp (MIL). When the
engine starts to run and no malfunction is detected in the system, MIL goes OFF but if a malfunction was or is de-
tected, MIL remains ON even when the engine is running.
INSPECTION
STEPACTIONYESNO
1MIL Power Supply Check
1) Turn ignition switch ON.
Do other indicator / warning lights in
combination meter comes ON?Go to Step 2.“IG COIL METER” fuse blown,
main fuse blown, ignition
switch malfunction, “B/W”
circuit between “IG COIL
METER” fuse and
combination meter or poor
coupler connection at
combination meter.
2ECM (PCM) Power and Ground Circuit
Check
Does engine start?Go to Step 3.Go to TABLE A-3 ECM (PCM)
POWER AND GROUND
CIRCUIT CHECK.
If engine is not cranked, go to
DIAGNOSIS in SECTION 8A.
3MIL Circuit Check
1) Turn ignition switch OFF and disconnect
connectors from ECM (PCM).
2) Check for proper connection to ECM
(PCM) at terminal C02-17.
3) If OK, then using service wire, ground
terminal C02-17 in connector
disconnected.
Does MIL turn on at ignition switch ON?Substitute a known-
good ECM (PCM) and
recheck.Bulb burned out or “V/Y” wire
circuit open.

Main fuse Ignition switch
Main fuseMalfunction indicator lamp in combination meter
Relay box“IG COIL METER”
6-42 ENGINE GENERAL INFORMATION AND DIAGNOSIS (TBI FOR G10)
TABLE A-3 ECM (PCM) POWER AND GROUND CIRCUIT CHECK – MIL
DOESN’T LIGHT AT IGNITION SWITCH ON AND ENGINE DOESN’T
START THOUGH IT IS CRANKED UP
CIRCUIT DESCRIPTION
When the ignition switch tuned ON, the main relay turns ON (the contact point closes) and the main power is sup-
plied to ECM (PCM).
INSPECTION
STEPACTIONYESNO
1Main Relay Operating Sound Check
Is operating sound of main relay heard at ignition switch ON?Go to Step 5.Go to Step 2.
2Main Relay Check
1) Turn OFF ignition switch and remove main relay (1).
2) Check for proper connection to main relay (1) at terminal
3 and 4.
3) Check resistance between each two terminals. See Fig. 1
and 2.
Between terminals 1 and 2: Infinity
Between terminals 3 and 4: 100 – 120 Ω
4) Check that there is continuity between terminals 1 and 2
when battery is connected to terminals 3 and 4. See Fig. 3.
Is main relay in good condition?Go to Step 3.Replace main
relay.
3Fuse Check
Is main “FI” fuse in good condition?Go to Step 4.Check for short in
circuits connected
to this fuse.
4ECM (PCM) Power Circuit Check
1) Turn OFF ignition switch, disconnect connectors from ECM
(PCM) and install main relay.
2) Check for proper connection to ECM (PCM) at terminals
C03-20, C02-2, C02-15 and C02-22.
3) If OK, then measure voltage between terminal C03-20 and
ground, C02-22 and ground with ignition switch ON.
Is each voltage 10 – 14 V?Go to Step 5.“B/W”, “W/R” or
“Bl / B” circuit
open.

Ignition coil
Igniter
Ignition switch
Main
fuse
Injector resistor
Fuel injector
Crankshaft
position sensor
Camshaft
position sensor
Ground
at engine “I / G COIL METER”
Main relay
6-68 ENGINE GENERAL INFORMATION AND DIAGNOSIS (TBI FOR G10)
DTC P0300 RANDOM MISFIRE DETECTED (Misfire detected at 2 or more
cylinders)
DTC P0301 CYLINDER 1 MISFIRE DETECTED
DTC P0302 CYLINDER 2 MISFIRE DETECTED
DTC P0303 CYLINDER 3 MISFIRE DETECTED
CIRCUIT DESCRIPTION
ECM (PCM) monitors crankshaft revolution speed and engine speed via the crankshaft position sensor and cylin-
der No. via the camshaft position sensor. Then it calculates the change in the crankshaft revolution speed and from
how many times such change occurred in every 200 or 1000 engine revolutions, it detects occurrence of misfire.
When ECM (PCM) detects a misfire (misfire rate per 200 revolutions) which can cause overheat and damage to
the three way catalytic converter, it makes the malfunction indicator lamp (MIL) flash as long as misfire occurs at
that rate.
After that, however, when the misfire rate drops, MIL remains ON until it has been judged as normal 3 times under
the same driving conditions.
Also, when ECM (PCM) detects a misfire (misfire rate per 1000 revolutions) which will not cause damage to three
way catalytic converter but can cause exhaust emission to be deteriorated, it makes MIL light according to the 2
driving cycle detection logic.