brake SUZUKI SWIFT 2000 1.G SF310 Service User Guide

“a”: Parking brake lever stroke:
4 – 9 notches (With 20 kg
or 44 lbs of pull pressure)
1. Wear indicator1. Clutch pedal
“a”: Free travel
0B-14 MAINTENANCE AND LUBRICATION
ITEM 5-4
Brake Lever and Cable Inspection
Parking brake lever

Check tooth tip of each notch for damage or wear. If any damage
or wear is found, replace parking lever.

Check parking brake lever for proper operation and stroke, and
adjust it if necessary.
For checking and adjusting procedures, refer to PARKING
BRAKE INSPECTION AND ADJUSTMENT of SECTION 5.
Parking brake cable
Inspect brake cable for damage and smooth movement.
Replace cable if it is in deteriorated condition.
CHASSIS AND BODY
ITEM 6-1
Clutch Pedal Free Travel Inspection
Check clutch pedal free travel. Refer to SECTION 7C for procedure
to check and adjust it.
ITEM 6-2
Tire and Wheel Disc Inspection
[Tire inspection]
1) Check tire for uneven or excessive wear, or damage. If defec-
tive, replace.
2) Check inflating pressure of each tire and adjust pressure to
specification as necessary.
NOTE:

Tire inflation pressure should be checked when tires are
cool.

Specified tire inflation pressure should be found on tire
placard or in owner’s manual which came with vehicle.

0B-20 MAINTENANCE AND LUBRICATION
FINAL INSPECTION
Seats
Check that seat slides smoothly and locks securely at
any position. Also check that reclining mechanism of
front seat back allows it to be locked at any angle.
Seat Belt
Inspect belt system including webbing, buckles, latch
plates, retractors and anchors for damage or wear.
If “REPLACE BELT” label on belt is visible, replace
belt.
Check that seat belt is securely locked.
Battery Electrolyte Level Check
Check that the electrolyte level of all battery cells is
between the upper and lower level lines on the case.
If battery is equipped with built-in indicator, check bat-
tery condition by the indicator.
Accelerator Pedal Operation
Check that pedal operates smoothly without getting
caught or interfered by and other part.
Engine Start
Check engine start for readiness.
On automatic transmission vehicles, try to start the
engine in each gear. The starter should crank only in
“P” (Park) or “N” (Neutral).
On manual transmission vehicles, place the shift le-
ver in “Neutral,” depress clutch pedal fully and try to
start.
Exhaust System Check
Check for leakage, cracks or loose supports.
Clutch (For manual transmission)
Check for the following.

Clutch is completely released when depressing
clutch pedal.

No slipping clutch occurs when releasing pedal and
accelerating.

Clutch itself is free from any abnormal condition.
Gearshift or Select Lever (Transmission)
Check gear shift or select lever for smooth shifting to
all positions and for good performance of transmis-
sion in any position.
With automatic transmission equipped vehicle, also
check that shift indicator indicates properly according
to which position select lever is shifted to.
CAUTION:
With automatic transmission equipped ve-
hicle, make sure that vehicle is at complete
stop when shifting select lever to “P” range
position and release all brakes.
Brake
[Foot brake]
Check the following;

that brake pedal has proper travel,

that brake works properly,

that it is free from noise,

that vehicle does not pull to one side when brake is
applied,

and that brake does not drag.
WARNING:
When carrying out road tests, select a safe
place where no man or no running vehicle is
seen so as to prevent any accident.
WARNING:
Before performing the following check, be
sure to have enough room around the vehicle.
Then, firmly apply both the parking brake and
the regular brakes. Do not use the accelerator
pedal. If the engine starts, be ready to turn off
the ignition promptly. Take these precautions
because the car could move without warning
and possibly cause personal injury or proper-
ty damage.

MAINTENANCE AND LUBRICATION 0B-21
[Parking brake]
Check that lever has proper travel.
Check to ensure that parking brake is fully effective
when the vehicle is stopped on the safe slope and
brake lever is pulled all the way.
Steering

Check to ensure that steering wheel is free from in-
stability, or abnormally heavy feeling.

Check that the vehicle does not wander or pull to
one side.
Engine

Check that engine responds readily at all speeds.

Check that engine is free from abnormal noise and
abnormal vibration.
Body, Wheels and Power Transmitting System
Check that body, wheels and power transmitting sys-
tem are free from abnormal noise and abnormal
vibration or any other abnormal condition.
Meters and Gauge
Check that speedometer, odometer, fuel meter, tem-
perature gauge, etc. are operating accurately.
Lights
Check that all lights operate properly.
Windshield Defroster
Periodically check that air comes out from defroster
outlet when operating heater or air conditioning.
Set fan switch lever to “HI” position and mode lever to
defroster position for this check. WARNING:
With vehicle parked on a fairly steep slope,
make sure nothing is in the way downhill to
avoid any personal injury or property damage.
Be prepared to apply regular brake quickly
even if vehicle should start to move.
RECOMMENDED FLUIDS AND LUBRICANTS
Engine oilSE, SF, SG, SH or SJ (Refer to engine oil viscosity chart in item 1-4.)
Engine coolantEthylene-glycol base coolant (“Antifreeze / Anticorrosion coolant”)
Brake fluidDOT3
Manual transmission oilSee SECTION 7A
Rear differential oilSee SECTION 7E
Automatic transmission fluidAn equivalent of DEXRON-IIE or DEXRON-III
Power steering fluidSee material table on SECTION 3B1
Door hingesEngine oil
Engine hood latchEngine oil
Key lock cylinderSpray lubricant

ENGINE GENERAL INFORMATION AND DIAGNOSIS (TBI FOR G10) 6-5
FUEL PRESSURE RELIEF PROCEDURE
CAUTION:
This work must not be done when engine is hot. If done so,
it may cause adverse effect to catalyst.
After making sure that engine is cold, release fuel pressure as fol-
lows.
1) Place transmission gear shift lever in “Neutral” (Shift selector le-
ver to “P” range for A / T model), set parking brake, and block
drive wheels.
2) Remove relay box cover.
3) Disconnect fuel pump relay (1) from relay box (2).
4) Remove fuel filler cap to release fuel vapor pressure in fuel tank
and then reinstall it.
5) Start engine and run it till it stops for lack of fuel. Repeat cranking
engine 2-3 times for about 3 seconds each time to dissipate fuel
pressure in lines. Fuel connections are now safe for servicing.
6) Upon completion of servicing, connect fuel pump relay to relay
box and install relay box cover.
FUEL LEAKAGE CHECK PROCEDURE
After performing any service on fuel system, check to make sure
that there are no fuel leakages as follows.
1) Turn ON ignition switch for 2 seconds (to operate fuel pump) and
then turn it OFF.
Repeat this (ON and OFF) 3 or 4 times and apply fuel pressure
to fuel line. (till fuel pressure is felt by hand placed on fuel feed
hose.)
2) In this state, check to see that there are no fuel leakages from
any part of fuel system.

6-24 ENGINE GENERAL INFORMATION AND DIAGNOSIS (TBI FOR G10)
ConditionPossible CauseReferring Item
Overheating
Inoperative thermostat

Poor water pump performance

Clogged or leaky radiator

Improper engine oil grade

Clogged oil filter or oil strainer

Poor oil pump performance

Faulty radiator fan control system

Dragging brakes

Slipping clutch

Blown cylinder head gasketThermostat in Section 6B
Water pump in Section 6B
Radiator in Section 6B
Engine oil and oil filter change in
Section 0B
Oil pressure check in Section 6A
Oil pressure check in Section 6A
Radiator fan control system in
Section 6E1
Trouble diagnosis in Section 5
Trouble diagnosis in Section 7C
Cylinder head in Section 6A
Poor gasoline
mileageIgnition system out of order

Leaks or loose connection of high-tension cord

Faulty spark plug (improper gap, heavy deposits
and burned electrodes, etc.)
Engine and emission control system out of
order

High idle speed

Poor performance of TP sensor, ECT sensor or
MAP sensor

Faulty fuel injector

Faulty fuel injector resistor

Faulty ECM (PCM)
Low compression
Others

Poor valve seating

Dragging brakes

Slipping clutch

Thermostat out of order

Improper tire pressure
High-tension cords in Section 6F
Spark plugs in Section 6F
Refer to item “Improper engine
idle speed” previously outlined
TP sensor, ECT sensor or MAP
sensor in Section 6E1
Diagnostic Flow Table B-1
Fuel injector resistor in Section 6E1
Previously outlined
Valves inspection in Section 6A
Trouble diagnosis in Section 5
Trouble diagnosis in Section 7C
Thermostat in Section 6B
Refer to Section 3F
Excessive engine
oil consumptionOil leakage

Blown cylinder head gasket

Leaky camshaft oil seals
Oil entering combustion chamber

Sticky piston ring

Worn piston and cylinder

Worn piston ring groove and ring

Improper location of piston ring gap

Worn or damaged valve stem seal

Worn valve stem
Cylinder head in Section 6A
Camshaft in Section 6A
Piston cleaning in Section 6A
Pistons and cylinders inspection
in Section 6A
Pistons inspection in Section 6A
Pistons assembly in Section 6A
Valves removal and installation in
Section 6A
Valves inspection in Section 6A

6-26 ENGINE GENERAL INFORMATION AND DIAGNOSIS (TBI FOR G10)
ConditionPossible CauseReferring Item
Engine has no
powerIgnition system out of order

Faulty spark plug

Faulty ignition coil with ignitor

Leaks, loose connection or disconnection of
high-tension cord
Engine overheating
Fuel system out of order

Clogged fuel hose or pipe

Malfunctioning fuel pump

Air inhaling from intake manifold gasket or
throttle body gasket
Engine and emission control system out of
order

Maladjusted accelerator cable play

Poor performance of TP sensor, ECT sensor or
MAP sensor

Faulty fuel injector

Faulty ECM (PCM)
Low compression
Others

Dragging brakes

Slipping clutch
Spark plugs in Section 6F
Ignition coil in Section 6F
High-tension cords in Section 6F
Refer to “Overheating” section
Diagnostic Flow Table B-3 in
Section 6
Diagnostic Flow Table B-2
Accelerator cable play in Section
6E1
TP sensor, ECT sensor or MAP
sensor in Section 6E1
Diagnostic Flow Table B-1
Previously outlined
Trouble diagnosis in Section 5
Trouble diagnosis in Section 7C

ENGINE GENERAL INFORMATION AND DIAGNOSIS (TBI FOR G10) 6-29
Ambient temp.
SCAN TOOL DATA
As the data values given below are standard values estimated on the basis of values obtained from the normally
operating vehicles by using a scan tool, use them as reference values. Even when the vehicle is in good condition,
there may be cases where the checked value does not fall within each specified data range. Therefore, judgment
as abnormal should not be made by checking with these data alone.
Also, conditions in the below table that can be checked by the scan tool are those detected by ECM (PCM) and
output from ECM (PCM) as commands and there may be cases where the engine or actuator is not operating (in
the condition) as indicated by the scan tool. Be sure to use the timing light to check the ignition timing.
NOTE:

With the generic scan tool, only star () marked data in the table below can be read.

When checking the data with the engine running at idle or racing, be sure to shift M / T gear to the neutral
gear position and A / T gear to the “Park” position and pull the parking brake fully. Also, if nothing or “no
load” is indicated, turn OFF A / C, all electric loads, P / S and all the other necessary switches.
SCAN TOOL DATAVEHICLE CONDITIONNORMAL CONDITION /
REFERENCE VALUES
FUEL SYSTEM B1 (FUEL
SYSTEM STATUS)At specified idle speed after warming upCLOSED (closed loop)

CALC LOAD
(CALCULATED LOADAt specified idle speed with no load after
warming up3 – 5%(
VALUE)At 2500 r / min with no load after warming up10 – 18%

COOLANT TEMP.
(ENGINE COOLANT
TEMP.)
At specified idle speed after warming up85 – 95C, 185 – 203F
SHORT FT BI (SHORT
TERM FUEL TRIM)At specified idle speed after warming up–20 – +20%
LONG FT BI (LONG
TERM FUEL TRIM)At specified idle speed after warming up–15 – +15%

MAP (INTAKE
MANIFOLD ABSOLUTE
PRESSURE)At specified idle speed with no load after
warming up29 – 48 kPa,
220 – 360 mmHg
ENGINE SPEEDAt idling with no load after warming upDesired idle speed
± 50 r / min
VEHICLE SPEEDAt stop0 km / h, 0 MPH

IGNITION ADVANCE
(IGNITION TIMING
ADVANCE FOR NO.1
CYLINDER)
At specified idle speed with no load after
warming up–1 – 18 BTDC
INTAKE AIR TEMP.At specified idle speed after warming up+35C (+63F)
–5C (–9F)
MAF (MASS AIR FLOW
RATE)
At specified idle speed with no load after
warming up1.0 – 3.0 gm / sec
RATE)At 2500 r / min with no load after warming up3.0 – 6.0 gm / sec

THROTTLE POS
(ABSOLUTEIgnition switch ON /Throttle valve fully closed7 – 18%
(ABSOLUTE
THROTTLE POSITION)
g
engine stoppedThrottle valve fully open70 – 90%
O2S B1 S1 (HEATED
OXYGEN SENSOR-1)At specified idle speed after warming up0.05 – 0.95 V
O2S B1 S2 (HEATED
OXYGEN SENSOR-2)When engine is running at 2000 r / min. for
3 min. or longer after warming up.0 – 0.95 V
O2S FT B1 S1At specified idle speed after warning up–20 – +20%
DIS. WITH MIL ON————

6-60 ENGINE GENERAL INFORMATION AND DIAGNOSIS (TBI FOR G10)
Usual driving: Driving at 30 – 40 mph, 50 – 60 km/h including short stop according to traffic signal. (under driving condition other than high-load,
high-engine speed, rapid accelerating and decelerating)1) 2) 3) 4) 5) 6) 7) 8) 9) 10) 11)and 50 mph
(80 km / h)
Above 20 mph
(32 km / h) Usual driving
DTC CONFIRMATION PROCEDURE
WARNING:

When performing a road test, select a place where there is no traffic or possibility of a traffic accident
and be very careful during testing to avoid occurrence of an accident.

Road test should be carried out with 2 persons, a driver and a tester, on a level road.
1) Turn ignition switch OFF.
Clear DTC with ignition switch ON, check vehicle and environmental condition for:
–Altitude (barometric pressure): 2400 m, 8000 ft or less (560 mmHg, 75 kPa or more)
–Ambient temp.: –10C, 14F or higher
–Intake air temp.: 70C, 158F or lower
–No exhaust gas leakage and loose connection
2) Warm up engine to normal operating temperature.
3) Drive vehicle under usual driving condition for 5 min. and check HO2S-2 output voltage and “short term fuel
trim” with “Data List” mode on scan tool, and write it down.
4) Stop vehicle (don’t turn ignition switch OFF).
5) Increase vehicle speed to higher than 20 mph, 32 km / h and then stop vehicle.
6) Repeat above steps 5) 4 times.
7) Increase vehicle speed to about 50 mph (80 km / h) in 3rd gear or 2 range.
8) Release accelerator pedal and with engine brake applied, keep vehicle coasting (fuel cut condition) for 10sec.
or more.
9) Stop vehicle (don’t turn ignition switch OFF) and run engine at idle for 2 min.
After this step 9), if “Oxygen Sensor Monitoring TEST COMPLETED” is displayed in “READINESS TESTS”
mode and DTC is not displayed in “DTC” mode, confirmation test is completed.
If “TEST NOT COMPLTD” is still being displayed, proceed to next step 10).
10) Drive vehicle under usual driving condition for 10 min. (or vehicle is at a stop and run engine at idle for 10 min.
or longer)
11) Stop vehicle (don’t turn ignition switch OFF). Confirm test results according to “Test Result Confirmation Flow
Table” in “DTC CONFIRMATION PROCEDURE” of DTC P0420.

6-82 ENGINE GENERAL INFORMATION AND DIAGNOSIS (TBI FOR G10)
Vehicle speed
sensor in
combination meterC03-2
C03-2
DTC P0500 VEHICLE SPEED SENSOR (VSS) MALFUNCTION (M / T)
CIRCUIT DESCRIPTION
DTC DETECTING CONDITIONPOSSIBLE CAUSE

VSS signal not inputted while vehicle running in “D”
range or during fuel cut at deceleration.
2 driving cycle detection logic, continuous monitoring
“B/Bl” circuit open

“Y/G” circuit open or short

VSS malfunction

ECM malfunction

Speedometer cable malfunction
DTC CONFIRMATION PROCEDURE
WARNING:

When performing a road test, select a place where there is no traffic or possibility of a traffic accident
and be very careful during testing to avoid occurrence of an accident.

Road test should be carried out with 2 persons, a driver and a tester.
1) Clear DTC and warm up engine to normal operating temperature.
2) Increase vehicle speed to 50 mph, 80 km / h in 3rd gear or “2” range while observing vehicle speed displayed
on scan tool.
3) Release accelerator pedal and with engine brake applied, keep vehicle coasting (fuel cut condition) for 4 sec.
or more.
4) Check pending DTC and DTC.

6-84 ENGINE GENERAL INFORMATION AND DIAGNOSIS (TBI FOR G10)
Vehicle speed sensor (on A / T)
Counter
shaft
gearPCMC03-2
C03-13
Bl
P
C03-2
C03-13
DTC P0500 VEHICLE SPEED SENSOR (VSS) MALFUNCTION FOR A / T
VEHICLE (A / T)
CIRCUIT DESCRIPTION – Refer to Section 6E1 for VSS operation.
DTC DETECTING CONDITIONPOSSIBLE CAUSE

While fuel is kept cut at lower than 4000 r / min for
longer than 4 sec.

VSS signal not inputted.
2 driving cycle detection logic, continuous
monitoring.
“BI” or “P” circuit open or short.

Vehicle speed sensor malfunction.

Foreign material being attached or sensor installed
improperly.

Gear damaged.
DTC CONFIRMATION PROCEDURE
WARNING:

When performing a road test, select a place where there is no traffic or possibility of a traffic accident
and be very careful during testing to avoid occurrence of an accident.

Road test should be carried out with 2 persons, a driver and a tester, on a level road.
1) Turn ignition switch OFF and then ON.
2) Clear DTC and warm up engine to normal operating temperature.
3) Increase vehicle speed to 50 mph, 80 km / h in “2” range.
4) Release accelerator pedal and with engine brake applied, keep vehicle coasting (fuel cut condition) for 4 sec.
or more.
5) Stop vehicle and check DTC and pending DTC.