Ignition SUZUKI SWIFT 2000 1.G SF310 Service Workshop Manual

6F1-4 IGNITION SYSTEM (SFI FOR G13)
IGNITION SYSTEM DIAGNOSTIC FLOW TABLE
STEPACTIONYESNO
1
Was “ENGINE DIAG. FLOW TABLE” performed?Go to Step 2.Go to “ENGINE DIAG.
FLOW TABLE” in
section 6.
2
Ignition Spark Test
1) Check all spark plugs for condition and type
referring to “Spark Plugs” section.
2) If OK, perform ignition spark test, referring to
“Ignition Spark Test” section.
Is spark emitted from all spark plugs?Go to Step 11.Go to Step 3.
3
Diagnostic Trouble Code (DTC) Check
Is DTC stored in ECM (PCM)?Go to applicable DTC
Diag. Flow Table in
section 6.Go to Step 4.
4
Electrical Connection Check
1) Check ignition coil assemblies and high-tension
cords for electrical connection.
Are they connected securely?Go to Step 5.Connect securely.
5
High-Tension Cords Check
1) Check high-tension cord for resistance referring
to “High-Tension Cords” section.
Is check result satisfactory?Go to Step 6.Replace high-tension
cord(s).
6
Ignition Coil Assembly Power Supply and Ground
Circuit Check
1) Check ignition coil assembly power supply and
ground circuits for open and short.
Are circuits in good condition?Go to Step 7.Repair or replace.
7
Ignition Coil Assembly Check
1) Check ignition coil for resistance referring to
“Ignition Coil Assembly” section.
Is check result satisfactory?Go to Step 8.Replace ignition coil
assembly.
8
Crankshaft Position (CKP) Sensor Check
1) Check crankshaft position sensor referring to
Step 3 and 4 of DTC P0335 Diag. Flow Table in
section 6.
Is check result satisfactory?Go to Step 9.Tighten CKP sensor
bolt, replace CKP
sensor or crankshaft
timing belt pulley.
9
Ignition Trigger Signal Circuit Check
1) Check ignition trigger signal wire for open, short
and poor connection.
Is circuit in good condition?Go to Step 10.Repair or replace.
10
A Known-good Ignition Coil Assembly Substitution
1) Substitute a known-good ignition coil assembly
and then repeat Step 2.
Is check result of Step 2 satisfactory?Go to Step 11.Substitute a known-
good ECM (PCM) and
then repeat Step 2.
11
Ignition Timing Check
1) Check initial ignition timing and ignition timing
advance referring to “Ignition Timing” section.
Is check result satisfactory?System is in good
condition.Check CKP sensor,
crankshaft timing belt
pulley (signal rotor)
and input signals
related to this system.

IGNITION SYSTEM (SFI FOR G13) 6F1-5
ON-VEHICLE SERVICE
IGNITION SPARK TEST
1) Disconnect all injector couplers (1) from injectors (2).
WARNING:
Without disconnection of injector couplers, combustible
gas may come out from spark plug holes during this test
and may get ignited in engine room.
2) Remove spark plug and check it for condition and type referring
to “Spark Plugs” in this section.
3) If OK, connect ignition coil coupler to ignition coil assembly and
connect spark plug to ignition coil assembly or high-tension
cord. Ground spark plug.
4) Crank engine and check if each spark plug sparks.
5) If no spark is emitted, inspect the related parts as described un-
der “Diagnosis” earlier in this section.
HIGH-TENSION CORDS
1) Disconnect high-tension cords (1) from ignition coil assemblies
(2) while gripping each cap.
2) Pull out high-tension cords from spark plugs while gripping each
cap.
CAUTION:
Pull out each connection by gripping cap portion so as
not to damage their inside wire (resistive conductor).
3) Measure resistance of high-tension cord (1) by using ohmmeter.
High-tension cord resistance: 4 – 10 kΩ/ m (1.2 – 3.0 kΩ/ ft)
4) If resistance exceeds specification, replace high-tension
cord(s).

“a”
6F1-6 IGNITION SYSTEM (SFI FOR G13)
5) Install high-tension cords (1) to spark plugs and ignition coil as-
semblies (2) while gripping each cap.
CAUTION:

Never attempt to use metal conductor high-tension
cords as replacing parts.

Insert each cap portion fully when installing high-ten-
sion cords.
SPARK PLUGS
1) Pull out high-tension cords by gripping their caps and then re-
move ignition coil assemblies referring to IGNITION COIL AS-
SEMBLY in this section.
2) Remove spark plugs.
3) Inspect them for:

Electrode wear

Carbon deposits

Insulator damage
4) If any abnormality is found, adjust air gap, clean with spark plug
cleaner or replace them with specified new plugs.
Spark plug air gap “a”: 1.0 – 1.1 mm ( 0.040 – 0.043 in.)
Spark plug type : NGK BKR6E-11
: DENSO K20PR-U11
5) Install spark plugs and torque them to specification.
Tightening Torque for spark plug
28 N.m (2.8 kg-m, 20.0 lb-ft)
6) Install ignition coil assemblies referring to IGNITION COIL AS-
SEMBLY in this section.
7) Install high-tension cords securely by gripping their caps.
IGNITION COIL ASSEMBLY
(INCLUDING IGNITOR)
Inspection
1) Disconnect negative cable at battery.
2) Disconnect ignition coil coupler.
3) Disconnect high-tension cord (3) from ignition coil assembly (2).
4) Remove ignition coil bolts (1) and then pull out ignition coil as-
sembly.

IGNITION SYSTEM (SFI FOR G13) 6F1-7
5) Measure secondary coil for resistance.
Secondary coil resistance : 7.6 – 10.2 kΩ at 20C, 68F
If resistance is out of specification, replace ignition coil assem-
bly.
6) Install ignition coil assembly.
7) Tighten ignition coil bolts, and then connect ignition coil coupler.
8) Install high-tension cord to ignition coil assembly while gripping
its cap.
CRANKSHAFT POSITION SENSOR
(CKP SENSOR)
Refer to section 6E2 for removal, inspection and installation.
IGNITION TIMING
NOTE:

Ignition timing is not adjustable. If ignition timing is out of
specification, check system related parts.

Before starting engine, place transmission gear shift lever in
“Neutral” (shift selector lever to “P” range for A / T model),
and set parking brake.
INSPECTION
1) Connect SUZUKI scan tool to DLC with ignition switch OFF.
Special Tool
(A): 09931-76011 (SUZUKI scan tool)
(B): Mass storage cartridge
(C): 09931-76030 (16 / 14 pin DLC cable)
2) Start engine and warm it up to normal operating temperature.
3) Make sure that all of electrical loads except ignition are switched
off.
4) Check to be sure that idle speed is within specification.
(Refer to SECTION 6E2)

6F1-8 IGNITION SYSTEM (SFI FOR G13)
5) Fix ignition timing to initial one as follow.
Select “MISC” mode on SUZUKI scan tool and fix ignition tim-
ing to initial one.
6) Detach air cleaner case and shift air cleaner case and hose
position to observe ignition timing.
7) Using timing light (1), check that ignition timing is within specifi-
cation.
Initial ignition timing (fixed with
SUZUKI scan tool) : 5
3 BTDC at idle speed
Ignition order : 1-3-4-2
8) If ignition timing is out of specification, check the followings:

CKP sensor

Crankshaft timing belt pulley (signal rotor)

TP sensor

VSS

Timing belt cover installation
9) After checking Initial Ignition Timing, release ignition timing
fixation by using SUZUKI scan tool.
10) With engine idling (throttle opening at closed position and ve-
hicle stopped), check that ignition timing is about 9–15
BTDC. (Constant variation within a few degrees from 9–15
indicates no abnormality but proves operation of electronic tim-
ing control system.) Also, check that increasing engine speed
advances ignition timing.
If above check results are not satisfactory, check CKP sensor
and ECM (PCM).
11) Install air cleaner case.

09931-76011
SUZUKI scan tool (Tech 1A) kit1. Storage case
2. Operator’s manual
3. Tech 1A
4. DLC cable (14 / 26 pin,
09931-76040)
5. Test lead / probe
6. Power source cable
7. DLC cable adaptor
8. Self-test adaptor
Mass storage cartridge09931-76030
16 / 14 pin DLC cable
IGNITION SYSTEM (SFI FOR G13) 6F1-9
SPECIAL TOOLS

7B
AUTOMATIC TRANSMISSION (3 A / T) (VEHICLE WITH WU-TWC) 7B-1
GENERAL DESCRIPTION7B- 3 . . . . . . . . . . . . . .
Electronic Shift Control System 7B- 5. . . . . . . . .
DIAGNOSIS7B-11 . . . . . . . . . . . . . . . . . . . . . . . . . . .
On-board diagnostic system 7B-11. . . . . . . . . . .
Precaution in Diagnosing Trouble 7B-12. . . . . . .
Automatic Transmission Diagnostic
Flow Table 7B-13. . . . . . . . . . . . . . . . . . . . . . . . . .
Customer problem inspection form
(example) 7B-15. . . . . . . . . . . . . . . . . . . . . . . .
Malfunction indicator lamp (MIL)
check 7B-16. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Diagnostic trouble code(s) check 7B-16. . . . .
Diagnostic trouble code(s)
clearance 7B-16. . . . . . . . . . . . . . . . . . . . . . . .
Diagnostic trouble code (DTC) table 7B-17. . .
Fail-safe table 7B-17. . . . . . . . . . . . . . . . . . . . . .
Visual inspection 7B-18. . . . . . . . . . . . . . . . . . .
Automatic Transmission Basic Check 7B-19. . .
Symptom-to-Inspection Table 7B-20. . . . . . . . . .
DTC P0705 Transmission Range
Sensor (Switch) Circuit Malfunction 7B-21. . . . DTC P0720 Output Speed Sensor
(A / T VSS) Circuit Malfunction 7B-24. . . . . . . . .
DTC P0753 Shift Solenoid-A (No.1)
Electrical 7B-26. . . . . . . . . . . . . . . . . . . . . . . . . . .
DTC P0758 Shift Solenoid-B (No.2)
Electrical 7B-26. . . . . . . . . . . . . . . . . . . . . . . . . . .
DTC P0751 Shift Solenoid-A (No.1)
Performance or Stuck Off 7B-28. . . . . . . . . . . . .
DTC P0756 Shift Solenoid-B (No.2)
Performance or Stuck Off 7B-28. . . . . . . . . . . . .
Table A-1 No Starting or Slipping in Any
Drive Range 7B-30. . . . . . . . . . . . . . . . . . . . . . . .
Table A-2 Gear Change Failure 7B-31. . . . . . . . .
Table A-3 Excessive Shock at Range
Selection or Gear Change 7B-31. . . . . . . . . . . .
Stall test 7B-32. . . . . . . . . . . . . . . . . . . . . . . . . . .
Line pressure test 7B-33. . . . . . . . . . . . . . . . . .
Road test 7B-35. . . . . . . . . . . . . . . . . . . . . . . . . .
Manual road test 7B-36. . . . . . . . . . . . . . . . . . .
Engine brake test 7B-36. . . . . . . . . . . . . . . . . . .
“P” range test 7B-37. . . . . . . . . . . . . . . . . . . . . .
Shift solenoid valve check 7B-37. . . . . . . . . . .
SECTION 7B
AUTOMATIC TRANSMISSION (3 A/T)
(VEHICLE WITH WU-TWC)
WARNING:
For vehicles equipped with Supplemental Restraint (Air Bag) System:

Service on and around the air bag system components or wiring must be performed only by an autho-
rized SUZUKI dealer. Refer to “Air Bag System Components and Wiring Location View” under “Gener-
al Description” in air bag system section in order to confirm whether you are performing service on
or near the air bag system components or wiring. Please observe all WARNINGS and “Service Precau-
tions” under “On-Vehicle Service” in air bag system section before performing service on or around
the air bag system components or wiring. Failure to follow WARNINGS could result in unintentional
activation of the system or could render the system inoperative. Either of these two conditions may
result in severe injury.

Technical service work must be started at least 90 seconds after the ignition switch is turned to the
“LOCK” position and the negative cable is disconnected from the battery. Otherwise, the system may
be activated by reserve energy in the Sensing and Diagnostic Module (SDM).
NOTE:
For the descriptions (items) not found in this section, refer to the same section of the Service Manual men-
tioned in the FOREWORD of this manual.
CONTENTS

[G10 Engine Model]
1. PCM
2. Camshaft position (CMP) sensor
3. Throttle position (TP) sensor
4. Engine coolant temperature (ECT) sensor
5. Transmission range sensor (shift switch)
6. Output shaft speed sensor (A / T VSS)7. Malfunction indicator lamp (MIL)
8. Data link connector (DLC)
9. Shift solenoid-A
(No.1, Direct clutch solenoid valve)
10. Shift solenoid-B
(No.2, 2nd brake solenoid valve)11. Ignition switch
12. Main relay
13. Inhibitor switch
14. To starter
15. Terminal arrangement of PCM coupler
(Viewed from harness side)
AUTOMATIC TRANSMISSION (3 A / T) (VEHICLE WITH WU-TWC) 7B-5
ELECTRONIC SHIFT CONTROL SYSTEM

7B-6 AUTOMATIC TRANSMISSION (3 A / T) (VEHICLE WITH WU-TWC)
[G13 Engine Model]
1. PCM
2. Camshaft position (CMP) sensor
3. Throttle position (TP) sensor
4. Engine coolant temperature (ECT) sensor
5. Transmission range sensor (shift switch)
6. Output shaft speed sensor (A / T VSS)7. Malfunction indicator lamp (MIL)
8. Data link connector (DLC)
9. Shift solenoid-A
(No.1, Direct clutch solenoid valve)
10. Shift solenoid-B
(No.2, 2nd brake solenoid valve)11. Ignition switch
12. Main relay
13. Inhibitor switch
14. To starter
15. Terminal arrangement of PCM coupler
(Viewed from harness side)

1. Malfunction indicator lamp (MIL)
2. Data link connector (DLC)
3. SUZUKI scan tool (Tech-1)
AUTOMATIC TRANSMISSION (3 A / T) (VEHICLE WITH WU-TWC) 7B-11
DIAGNOSIS
This vehicle is equipped with an electronic transmission control system, which control the automatic shift up and
shift down timing, etc. suitably to vehicle driving conditions.
PCM (ECM) has an On-Board Diagnosis System which detects a malfunction in this system and abnormality of
those parts that influence the engine exhaust emission.
When diagnosing a trouble in transmission including this system, be sure to have full understanding of the outline
of “ON-BOARD DIAGNOSTIC SYSTEM” and each item in “PRECAUTION IN DIAGNOSING TROUBLE” and
execute diagnosis according to “AUTOMATIC TRANSMISSION DIAGNOSTIC FLOW TABLE” given below to ob-
tain correct result smoothly.
ON-BOARD DIAGNOSTIC SYSTEM
For automatic transmission control system, PCM (ECM) has follow-
ing functions. Refer to Section 6 or 6-1 for details.

When ignition switch is turned ON with engine at a stop malfunc-
tion indicator lamp (MIL) turns ON to check bulb of MIL.

When PCM detects a malfunction in A / T control system (and / or
a malfunction which gives an adverse effect to vehicle emission)
while engine is running, it makes malfunction indicator lamp in
meter cluster of instrument panel turn ON and stores malfunction
area (DTC) in its memory.
If it detects that continuously 3 driving cycles are normal after de-
tecting a malfunction, however, it makes MIL turn OFF although
DTC stored in its memory will remain.

It is possible to communicate with PCM through data link connect-
er (DLC) by using SUZUKI scan tool (Tech-1).
(Diagnostic information can be checked and erased by using a
scan tool)
2 Driving Cycle Detection Logic
Refer to Section 6 or 6-1 for details.
Freeze Frame Data
Refer to Section 6 or 6-1 for details.