Ignition SUZUKI SWIFT 2000 1.G SF310 Service Workshop Manual

1. Malfunction indicator
lamp (MIL)
1. Data link connector (DLC)
1. Data link connector (DLC)
7B-16 AUTOMATIC TRANSMISSION (3 A / T) (VEHICLE WITH WU-TWC)
MALFUNCTION INDICATOR LAMP (MIL) CHECK
Refer to the same item in Section 6 or 6-1 for checking procedure.
DIAGNOSTIC TROUBLE CODE(S) CHECK
1) Turn ignition switch OFF.
2) After setting cartridge to SUZUKI scan tool, connect it to data link
connector (DLC) located on underside of instrument panel at
driver’s seat side.
Special Tool
(A): 09931-76011 (SUZUKI scan tool)
(B): Mass storage cartridge
(C): 09931-76030 (16 / 14 pin DLC cable)
3) Turn ignition switch ON.
4) Read DTC according to instructions displayed on SUZUKI scan
tool and print it or write it down. Refer to SUZUKI scan tool opera-
tor’s manual for further details.
5) After completing the check, turn ignition switch OFF and discon-
nect SUZUKI scan tool from data link connector (DLC).
DIAGNOSTIC TROUBLE CODE(S) CLEARANCE
1) Turn ignition switch OFF.
2) After setting cartridge to SUZUKI scan tool, connect it to data link
connector (DLC) located on underside of instrument panel at
driver’s seat side.
Special Tool
(A): 09931-76011 (SUZUKI scan tool)
(B): Mass storage cartridge
(C): 09931-76030 (16 / 14 pin DLC cable)
3) Turn ignition switch ON.
4) Erase DTC according to instructions displayed on SUZUKI scan
tool. Refer to SUZUKI scan tool operator’s manual for further de-
tails.
5) After completing the check, turn ignition switch OFF and discon-
nect SUZUKI scan tool from data link connector (DLC).

AUTOMATIC TRANSMISSION (3 A / T) (VEHICLE WITH WU-TWC) 7B-19
Fig. 1 for Step 5. Fig. 2 for Step 5. Fig. 3 for Step 5.
When not using SUZUKI
scan tool:
lever position
Terminal
Selector
AUTOMATIC TRANSMISSION BASIC CHECK
This check is very important for troubleshooting when PCM (ECM) has detected no DTC and no abnormality has
been found in visual inspection. Follow the flow table carefully.
STEPACTIONYESNO
1Was “AUTOMATIC TRANSMISSION DIAG. FLOW TABLE”
performed?Go to Step 2.Go to
“AUTOMATIC
TRANSMISSION
DIAG. FLOW
TABLE”.
2Check A / T Fluid.
Warm transmission to normal operating temperature and check
fluid level and contamination referring to “FLUID LEVEL
CHECK” of “ON-VEHICLE SERVICE” in this section.
Is it in good condition?Go to Step 3.Add or change
fluid.
3Check Fluid Pressure Control Cable.
1) Warm up engine to normal operating temperature.
2) Check fluid pressure control cable for play referring to
“FLUID PRESSURE CONTROL CABLE” of “ON-VEHICLE
SERVICE” in this section.
Is it in good condition?Go to Step 4.Adjust.
4Check Select Cable for Adjustment referring to “SELECT
CABLE” of “ON-VEHICLE SERVICE” in this section.
Is it adjusted correctly?Go to Step 5.Adjust.
5Check Transmission Range Sensor (Switch) Circuit for
Operation.
When using SUZUKI scan tool:
1) Connect SUZUKI scan tool to DLC with ignition switch OFF.
2) Turn ignition switch ON and check transmission range
signal (P, R, N, D, 2 or L) on display when shifting manual
selector to each range. See Fig. 1.
Is applicable range indicated?
When not using SUZUKI scan tool:
1) Turn ignition switch ON.
2) Check voltage at terminals C03-3 C03-4 C03-5 C03-14
Go to Step 6.Go to Step 3 of
DTC P0705
Flow Table.
2) Check voltage at terminals C03-3, C03-4, C03-5, C03-14,
C03-15 and C03-16 for G10 engine model (C02-11, C02-12,
C02-14, C02-15, C02-21 and C02-23 for G13 engine
model) respectively with selector lever shifted to each
range. See Fig. 2.
Taking terminal C03-3 for G10 engine model (C02-11 for
G13 engine model) as an example, is battery voltage
indicated only when selector lever is shifted to “2” range and
0 V for other ranges as shown in Fig. 3?
Check voltage at other terminals likewise, referring to Fig. 3.
Are check results satisfactory?
6Check Engine Idle speed referring to Section 6E1 or 6E2.
Is it in good condition?Go to
“SYMPTOM-TO-
INSPECTION
TABLE” below.Go to Section
6E1 or 6E2.
C03-5
(C02-21)C03-16
(C02-15)C03-4
(C02-12)C03-15
(C02-14)C03-3
(C02-11)C03-14
(C02-23)
PB + V0 V0 V0 V0 V0 V
R0 VB + V0 V0 V0 V0 V
N0 V0 VB + V0 V0 V0 V
D0 V0 V0 VB + V0 V0 V
20 V0 V0 V0 VB + V0 V
L0 V0 V0 V0 V0 VB + V

*1: For G10 engine model
*2: For G13 engine model
1. PCM
2. Transmission range sensor
3. From ignition switch
4. Shift indicator
5. Backup lamp
6. Terminal arrangement of PCM
coupler (Viewed from harness side)
Gr / Bl (*1), R / B (*2)
AUTOMATIC TRANSMISSION (3 A / T) (VEHICLE WITH WU-TWC) 7B-21
DTC P0705 TRANSMISSION RANGE SENSOR (SWITCH) CIRCUIT
MALFUNCTION
CIRCUIT DESCRIPTION – Refer to “GENERAL DESCRIPTION” in this section.
DTC DETECTING CONDITION
POSSIBLE CAUSE
DTC will set when either condition A or condition B
occurs.
A: No signal is inputted at ignition switch ON.
B: Multiple signals are inputted while running at higher
than specified vehicle speed with gear in 3rd gear
of “D” range.
“Y”, “Or / B”, “R”, “Or / Y”, “Gr / R”, “Gr” or “Gr / Bl”
(G10 engine model) (“Br / Y”, “W/B”, “R/W”, “W/R”,
“Y/R”, “Y/B” or “R/B” (G13 engine model)) circuit
open or short.

Transmission range sensor malfunction.

Select cable maladjusted.

PCM malfunction.
DTC CONFIRMATION PROCEDURE
WARNING:

When performing a road test, select a place where there is no traffic or possibility of a traffic accident
and be very careful during testing to avoid occurrence of an accident.

Road test should be carried out with 2 persons, a driver and a tester, on a level road.
1) Turn ignition switch OFF and then ON.
2) Clear DTC and warm up engine to normal operating temperature.
3) Shift selector lever to each of P, R, N, D, 2 and L ranges and hold it there for longer than 5 seconds each.
4) Check for DTC and if no DTC appears on display, proceed to the next step.
5) Drive vehicle at 40 mph, 60 km / h or more in 3rd gear of “D” range for longer than 5 sec.
6) Stop vehicle and check DTC.

7B-22 AUTOMATIC TRANSMISSION (3 A / T) (VEHICLE WITH WU-TWC)
Fig. 1 for Step 2. Fig. 2 for Step 2.
Fig. 3 for Step 2.
When not using SUZUKI
scan tool:
lever position
Terminal
Selector
TROUBLESHOOTING
STEPACTIONYESNO
1Was “AUTOMATIC TRANSMISSION DIAGNOSTIC FLOW
TABLE” performed?Go to Step 2.Go to
“AUTOMATIC
TRANSMISSION
DIAGNOSTIC
FLOW TABLE”.
2Check Transmission Range Sensor Circuit for Operation.
When using SUZUKI scan tool:
1) Connect SUZUKI scan tool to DLC with ignition switch OFF.
2) Turn ignition switch ON and check transmission range
signal (P, R, N, D, 2 or L) on display when shifting manual
selector to each range. See Fig. 1.
Is applicable range indicated?
When not using SUZUKI scan tool:
1) Turn ignition switch ON.
2) Check voltage at terminals C03-3, C03-4, C03-5, C03-14,
C03-15 and C03-16 for G10 engine model (C02-11, C02-12,
C02-14, C02-15, C02-21 and C02-23 for G13 engine model)
respectively with selector lever shifted to each range. See Fig. 2.
Taking terminal C03-3 for G10 engine model (C02-11 for G13
engine model) as an example, is battery voltage indicated only
when selector lever is shifted to “2” range and 0 V for other
ranges as shown in Fig. 3?
Check voltage at other terminals likewise, referring to Fig. 3.
Are check results satisfactory?Intermittent
trouble. Check
for intermittent
referring to
“INTERMITTENT
AND POOR
CONNECTION”
in Section 0A.Go to Step 3.
3Check Select Cable for Adjustment referring to “SELECT
CABLE” of “ON-VEHICLE SERVICE” in this section.
Is it adjusted correctly?Go to Step 4.Adjust.
4Check Transmission Range Sensor.
1) Remove TR sensor from A / T.
2) At each of P, R, N, D, 2 and L shift position, check continuity
between terminals as well as each terminal and sensor
case. See Fig. 4.
Continuity should be indicated only between those
terminals as shown in Fig. 4 and 5 at each shift position.
Continuity should not exist between any terminal and
sensor case.
Are check results satisfactory?Go to Step 5.Replace TR
sensor.
5Check Transmission Range Sensor for Installation Position.
1) Install TR sensor to transmission referring to
“TRANSMISSION RANGE SENSOR” of “ON-VEHICLE
SERVICE” in this section.
2) Perform check as described in step 2 of this table.
Is check result satisfactory?Transmission
range sensor
maladjusted.Check “Y”, “Or / B”,
“R”, “Or / Y”,
“Gr / R”, “Gr” or
“Gr / Bl” (G10
engine model)
(“Br / Y”, “W/B”,
“R/W”, “W/R”,
“Y/R”, “Y/B” or
“R/B” (G13 engine
model)) circuit for
open or short.
If wires and
connections are
OK, substitute a
known-good PCM
and recheck.
C03-5
(C02-21)C03-16
(C02-15)C03-4
(C02-12)C03-15
(C02-14)C03-3
(C02-11)C03-14
C02-23)
PB + V0 V0 V0 V0 V0 V
R0 VB + V0 V0 V0 V0 V
N0 V0 VB + V0 V0 V0 V
D0 V0 V0 VB + V0 V0 V
20 V0 V0 V0 VB + V0 V
L0 V0 V0 V0 V0 VB + V

Counter
shaft gear
*1: For G10 engine model
*2: For G13 engine model
1. PCM
2. Output shaft speed sensor
3. Terminal arrangement of PCM coupler
(Viewed from harness side)
7B-24 AUTOMATIC TRANSMISSION (3 A / T) (VEHICLE WITH WU-TWC)
DTC P0720 OUTPUT SPEED SENSOR (A / T VSS) CIRCUIT MALFUNCTION
CIRCUIT DESCRIPTION – Refer to “GENERAL DESCRIPTION” in this section.
DTC DETECTING CONDITION
POSSIBLE CAUSE
No signal inputted while running vehicle with “D” or “2”
range.
“P” or “Bl” circuit open or short.

Output shaft speed sensor malfunction.

Foreign material being attached or sensor installed
improperly.

Gear damaged.
DTC CONFIRMATION PROCEDURE
WARNING:

When performing a road test, select a place where there is no traffic or possibility of a traffic accident
and be very careful during testing to avoid occurrence of an accident.

Road test should be carried out with 2 persons, a driver and a tester, on a level road.
1) Turn ignition switch OFF and then ON.
2) Clear DTC, shift selector lever to “2” range and drive vehicle at 3500 r / min engine speed for 3.5 seconds.
3) Stop vehicle and check DTC.

AUTOMATIC TRANSMISSION (3 A / T) (VEHICLE WITH WU-TWC) 7B-25
Fig. 1 for Step 2. Fig. 2 for Step 3. Fig. 3 for Step 3.
TROUBLESHOOTING
STEPACTIONYESNO
1Was “AUTOMATIC TRANSMISSION DIAGNOSTIC
FLOW TABLE” performed?Go to Step 2.Go to
”AUTOMATIC
TRANSMISSION
DIAGNOSTIC
FLOW TABLE”.
2Check Output Shaft Speed Sensor for Resistance.
1) Disconnect output shaft speed sensor connector with
ignition switch OFF.
2) Check for proper connection to output shaft speed
sensor at “P” and “Bl” wire terminals.
3) If OK, then check resistance of output shaft speed
sensor. See Fig. 1.
Resistance between terminals : 100 – 300 Ω
Resistance between terminal
and transmission : 1 MΩ or more
Are check results satisfactory?Go to Step 3.Replace output
shaft speed
sensor.
3Check visually output shaft speed sensor and counter
shaft gear for the following.
See Fig. 2 and 3.

No damage

No foreign material attached

Correct installation
Are they in good condition?“P” or “Bl” wire open or
shorted to ground or
poor C03-2 or C03-13
for G10 engine model
(C03-2 or C03-8 for
G13 engine model)
connection.
If wire and connection
are OK, intermittent
trouble or faulty PCM.
Check for intermittent
referring to
“INTERMITTENT
AND POOR
CONNECTION” in
Section 0A.Clean, repair or
replace.

1. PCM
2. Shift solenoid-A (No.1, Direct clutch solenoid)
3. Shift solenoid-B (No.2, 2nd brake solenoid)
4. Terminal arrangement of PCM coupler
(Viewed from harness side)*1: For G10 engine model
*2: For G13 engine model
7B-26 AUTOMATIC TRANSMISSION (3 A / T) (VEHICLE WITH WU-TWC)
DTC P0753 SHIFT SOLENOID-A (NO.1) ELECTRICAL
DTC P0758 SHIFT SOLENOID-B (NO.2) ELECTRICAL
CIRCUIT DESCRIPTION – Refer to “GENERAL DESCRIPTION” of this section.
DTC DETECTING CONDITION
POSSIBLE CAUSE
Output command from PCM and output voltage do not
agree.DTC P0753:

“G/W” circuit open or short

Shift solenoid-A malfunction

PCM malfunction
DTC P0758:

“G/Or” circuit open or short

Shift solenoid-B malfunction

PCM malfunction
DTC CONFIRMATION PROCEDURE
1) Turn ignition switch OFF.
2) Clear DTC with ignition switch ON and warm up engine to normal operating temperature at “P” range.
3) Shift selector lever to “D” range for 1 sec. or longer.
4) Shift it to “P” range and check DTC.

AUTOMATIC TRANSMISSION (3 A / T) (VEHICLE WITH WU-TWC) 7B-27
Fig. 1 for Step 2. Fig. 2 for Step 2. Fig. 3 for Step 3.
When using SUZUKI scan tool: When not using SUZUKI scan tool:Terminal for solenoid-B (C29-2)
Terminal for
solenoid-A (C29-1)
TROUBLESHOOTING
STEPACTIONYESNO
1Was “AUTOMATIC TRANSMISSION DIAGNOSTIC FLOW
TABLE” performed?Go to Step 2.Go to
“AUTOMATIC
TRANSMISSION
DIAGNOSTIC
FLOW TABLE”.
2Check Shift Solenoid Circuit.
When using SUZUKI scan tool:
1) Connect SUZUKI scan tool to DLC with ignition switch OFF.
2) Turn ignition switch ON.
3) Select “Data list” mode on scan tool. See Fig. 1.
4) Check “SHIFT SOL A-MONI” or “SHIFT SOL B-MONI” on
scan tool at “N” and “D” range.
“N” range: OFF
“D” range: ON
Is OFF / ON displayed as described above?
When not using SUZUKI scan tool:
1) Turn ignition switch ON.
2) Check voltage at terminal C02-8 or C02-9 for G10 engine
model (C03-4 or C03-11 for G13 engine model) of PCM
connector connected. See Fig. 2.
“N” range: 0 V
“D” range: 10 – 14 V
Is voltage displayed as described above?Intermittent
trouble.
Check for
intermittent
referring to
“INTERMITTENT
AND POOR
CONNECTION”
in Section 0A.Go to Step 3.
3Check Shift Solenoid for Resistance.
1) Turn ignition switch OFF.
2) Disconnect connector of shift solenoid.
3) Check resistance between solenoid terminal C29-1 or
C29-2 and transmission. See Fig. 3.
Is it 8 – 20 Ω?“G/W” or “G/Or”
wire open or
short, or poor
C02-8 or C02-9
for G10 engine
model (C03-4 or
C03-11 for G13
engine model)
connection.
If wire and
connection are
OK, substitute a
known-good
PCM and
recheck.Replace shift
solenoid.

ACCEPTABLE RANGE
1st gear (solenoids ON and ON)
2nd gear
(solenoids ON and OFF)
3rd gear
(solenoids OFF and OFF)
Vehicle speed
Engine speed
7B-28 AUTOMATIC TRANSMISSION (3 A / T) (VEHICLE WITH WU-TWC)
DTC P0751 SHIFT SOLENOID-A (No.1) PERFORMANCE OR STUCK OFF
DTC P0756 SHIFT SOLENOID-B (No.2) PERFORMANCE OR STUCK OFF
CIRCUIT DESCRIPTION
PCM monitors throttle opening, engine speed, vehicle speed and gear position and compares the actual engine
speed and its specified value (i.e., engine speed obtained by PCM through calculation using the throttle open-
ing / gear position and vehicle speed).
DTC DETECTING CONDITION
POSSIBLE CAUSE

While running in “D” range after engine warmed up,
engine speed as compared with vehicle speed is not
within acceptable range.
2 driving cycle detection logic, continuous
monitoring.
A / T oil pressure control cable maladjusted

Selector cable maladjusted

Mechanical malfunction of shift solenoid valve
(stick or leakage)

Mechanical malfunction in transmission

Torque converter malfunction
DTC CONFIRMATION PROCEDURE
WARNING:

When performing a road test, select a place where there is no traffic or possibility of a traffic accident
and be very careful during testing to avoid occurrence of an accident.

Road test should be carried out with 2 persons, a driver and a tester, on a level road.
1) Turn ignition switch OFF.
2) Clear DTC with ignition switch ON and warm up engine to normal operating temperature.
3) Shift selector lever to “D” range.
4) Start vehicle and increase vehicle speed to 40 – 55 km / h ( 25 – 35 mile / h) by depressing accelerator pedal half
a stroke.
5) Keep vehicle at above speed for 5 sec. or longer.
6) Increase vehicle speed to 75 – 90 km / h (45 – 55 mile / h) by depressing accelerator pedal half a stroke and keep
it at that speed for 5 sec. or longer.
7) Stop vehicle and check pending DTC and DTC.

1. PCM coupler disconnected
AUTOMATIC TRANSMISSION (3 A / T) (VEHICLE WITH WU-TWC) 7B-39
TRANSMISSION RANGE SENSOR CHECK
Check transmission range sensor referring to Step 2 of DTC P0705
Flow Table.
OUTPUT SHAFT SPEED SENSOR CHECK
1) Turn OFF ignition switch.
2) Disconnect coupler(s) from powertrain control module.
3) Bring ohmmeter probes in touch with coupler terminals from har-
ness side.
4) Check resistance of output shaft speed sensor.
Resistance between terminals
C03-2 and C03-13
(For G10 engine model)
C03-2 and C03-8
(For G13 engine model) : 100 – 300 Ω
Resistance between terminal
and ground : 1 MΩ or more
If resistance are out of specification, check wire harness and
connector for open or short and output shaft speed sensor itself
for resistance.
If resistance are within above specifications, proceed to next
step.
5) Visually check output shaft speed sensor and counter shaft gear
for the following:

No damage

No foreign material attached

Correct installation
If any malfunction is found, clean, repair or replace.