idle SUZUKI SWIFT 2000 1.G SF310 Service Owner's Guide

ENGINE GENERAL INFORMATION AND DIAGNOSIS (TBI FOR G10) 6-69
Below
specified value DTC DETECTING CONDITION
POSSIBLE CAUSE

Engine under other than high revolution condition

Not on rough road

Engine speed changing rate

Manifold absolute
pressure changing rate

Throttle opening changing rate

Misfire rate per 200 or 1000 engine revolutions (how
much and how often crankshaft revolution speed
changes) is higher than specified value
Engine overheating

Vacuum leaks (air inhaling) from air intake system

Ignition system malfunction (spark plug(s), high-
tension cord(s), ignition coil assembly)

Fuel pressure out of specification

Fuel injector malfunction (clogged or leakage)

Engine compression out of specification

Valve lash (clearance) out of specification

Manifold absolute pressure sensor malfunction

Engine coolant temp. sensor malfunction

PCV valve malfunction

EVAP control system malfunction
DTC CONFIRMATION PROCEDURE
WARNING:

When performing a road test, select a place where there is no traffic or possibility of a traffic accident
and be very careful during testing to avoid occurrence of an accident.

Road test should be carried out with 2 persons, a driver and a tester.
1) Turn ignition switch OFF.
2) Clear DTC with ignition switch ON.
3) Check vehicle and environmental condition for:
–Altitude (barometric pressure): 2400 m, 8000 ft or less (560 mmHg, 75 kPa or more)
–Ambient temp.: –10C, 14F or higher
–Intake air temp.: 70C, 158F or lower
–Engine coolant temp.: –10 – 11 0C, 14 – 230F
4) Start engine and keep it at idle for 2 min. or more.
5) Check DTC in “DTC” mode and pending DTC in “ON BOARD TEST” or “PENDING DTC” mode.
6) If DTC is not detected at idle, consult usual driving based on information obtained in “Customer complaint analy-
sis” and “Freeze frame data check”.

6-70 ENGINE GENERAL INFORMATION AND DIAGNOSIS (TBI FOR G10)
INSPECTION
STEPACTIONYESNO
1Was “ENGINE DIAG. FLOW TABLE” performed?Go to Step 2.Go to “ENGINE
DIAG. FLOW
TABLE“.
2Is there DTC other than Fuel system (DTC P0171 / P0172)
and misfire (DTC P0300-P0303)?Go to applicable
DTC Diag.
Flow Table.Go to Step 3.
3Check Ignition System.
1) Remove spark plugs and check them for;

Air gap: 1.0 – 1.1 mm (0.040 – 0.043 in.) See Fig. 1.

Carbon deposits

Insulator damage

Plug type
If abnormality is found, adjust, clean or replace.
2) Disconnect injector connector. See Fig. 2.
3) Connect spark plugs to high tension cords and then
ground spark plugs.
4) Crank engine and check that each spark plug sparks.
Are above check results satisfactory?Go to Step 4.Check ignition
system parts
(Refer to Section
6F).
4Check Fuel Pressure (Refer to Section 6E1 for details).
1) Release fuel pressure from fuel feed line.
2) Install fuel pressure gauge. See Fig. 3.
3) Check fuel pressure.
With fuel pump operating
and engine at stop : 160 – 210 kPa, 1.6 – 2.1 kg / cm
2,
22.7 – 29.9 psi.
At specified idle speed : 90 – 140 kPa, 0.9 – 1.4 kg / cm
2,
12.8 – 20.0 psi.
Is measured value as specified?
Go to Step 5.Go to Diag. Flow
Table B-3 fuel
pressure check.
5Check Fuel Injector and Circuit.
1) Turn ignition switch OFF and disconnect fuel injector
connector.
2) Check for proper connection to fuel injector at each terminal.
3) If OK, then check injector resistance. See Fig. 4.
Injector resistance: 0.5 – 1.5 Ω at 20C (68F).
4) Connect injector connector.
5) Check that fuel is injected out in conical shape from fuel
injector when running engine.
6) Check injector for fuel leakage after engine stop.
Fuel leakage: Less than 1 drop / min.
Is check result satisfactory?Go to Step 6.Check injector
circuit or replace
fuel injector.

ENGINE GENERAL INFORMATION AND DIAGNOSIS (TBI FOR G10) 6-71
1. Throttle body
2. Fuel feed hose
GoodNo good1. Injector connector
STEPACTIONYESNO
6Check PCV valve for clogging (See Section 6E1).
Is it in good condition?Go to Step 7.Replace PCV valve.
7Check EVAP Canister Purge Valve for Closing.
1) Disconnect purge hose (1) from EVAP canister.
2) Place finger against the end of disconnected hose.
3) Check that vacuum is not felt there, when engine is
cool and running at idle. See Fig. 5.
Is vacuum felt?Check EVAP
control system
(See Section 6E1).Go to Step 8.
8Check intake manifold pressure sensor for performance
(See Section 6E1).
Is it in good condition?Go to Step 9.Repair or replace.
9Check engine coolant temp. sensor for performance
(See Section 6E1).
Is it in good condition?Go to Step 10.Replace engine
coolant temp.
sensor.
10Check parts or system which can cause engine rough
idle or poor performance.
–Engine compression (See Section 6A).
–Valve lash (See Section 6A).
–Valve timing (Timing belt installation. See Section 6A).
Are they in good condition?Check wire harness
and connection of
ECM (PCM) ground,
ignition system and
fuel injector for
intermittent open
and short.Repair or replace.
Fig. 1 for Step 3 Fig. 2 for Step 3 Fig. 3 for Step 4
Fig. 4 for Step 5 Fig. 5 for Step 7

Oscilloscope Waveforms
Crankshaft
timing belt pulleyCKP
sensor
2V/Div.
5ms/Div.
Waveforms at specified idle speed
6-72 ENGINE GENERAL INFORMATION AND DIAGNOSIS (TBI FOR G10)
DTC P0335 CRANKSHAFT POSITION (CKP) SENSOR CIRCUIT MALFUNCTION
CIRCUIT DESCRIPTION
DTC DETECTING CONDITIONPOSSIBLE CAUSE

No CKP sensor signal during 1 revolution of
camshaft.
CKP sensor circuit open or short.

Crankshaft timing belt pulley teeth damaged.

CKP sensor malfunction, foreign material being
attached or improper installation.

ECM (PCM) malfunction.
Reference
Connect oscilloscope between terminals C01-3 (+) and C01-11 (–) of ECM (PCM) connector connected to ECM
(PCM) and check CKP sensor signal.
DTC CONFIRMATION PROCEDURE
1) Clear DTC, start engine and keep it at idle for 1 min.
2) Select “DTC” mode on scan tool and check DTC.

Display of fuel injection signal using oscilloscope
1. CMP sensor signal
2. Fuel injector signal
3. Fuel injection time
2V/Div.
20V/Div.1
2
10ms/Div
Waveforms at specified idle speed 3 Sensor rotor
in distributorCamshaft
position sensor
6-74 ENGINE GENERAL INFORMATION AND DIAGNOSIS (TBI FOR G10)
DTC P0340 CAMSHAFT POSITION (CMP) SENSOR CIRCUIT MALFUNCTION
CIRCUIT DESCRIPTION
DTC DETECTING CONDITIONPOSSIBLE CAUSE

No CMP sensor signal for 2 seconds at engine
cranking (CKP sensor signal is inputted).
CMP sensor circuit open or short.

Signal rotor teeth damaged.

CMP sensor malfunction, foreign material being
attached or improper installation.

ECM (PCM) malfunction.
Reference
Connect oscilloscope between terminals C01-2 and C01-10 of ECM (PCM) connector connected to ECM (PCM)
and check CMP sensor signal.
DTC CONFIRMATION PROCEDURE
1) Clear DTC.
2) Start engine and keep it at idle for 1 min.
3) Select “DTC” mode on scan tool and check DTC.

6-76 ENGINE GENERAL INFORMATION AND DIAGNOSIS (TBI FOR G10)
Oscilloscope Waveforms
Engine running at
Closed loop conditionFuel
CutIdle after fuel cut 0.5 V / Div
2 sec. / Div Heated
oxygen
sensor-1
Warm up three way
catalytic converter (if equipped)
Three way catalytic converterTo other sensor
To other
sensors
Heated oxygen sensor-2
G
DTC P0420 CATALYST SYSTEM EFFICIENCY BELOW THRESHOLD
CIRCUIT DESCRIPTION
ECM (PCM) monitors oxygen concentration in the exhaust gas which has passed the three way catalytic converter
by HO2S-2.
When the catalyst is functioning properly, the variation cycle of HO2S-2 output voltage (oxygen concentration) is
slower than that of HO2S-1 output voltage because of the amount of oxygen in the exhaust gas which has been
stored in the catalyst.
Reference
DTC DETECTING CONDITIONPOSSIBLE CAUSE

While vehicle running at constant speed under other
than high load.

Time from rich or lean switching command is output
till HO2S-2 output voltage crosses 0.45 V is less than
specified value.
2 driving cycle detection logic, monitoring once / 1
driving.
Exhaust gas leak

Three way catalytic converter malfunction

Fuel system malfunction

HO2S-2 malfunction

HO2S-1 malfunction

Main
fuseMain relay
Idle speed
control relay
To TP sensor
Idle speed control actuator
6-86 ENGINE GENERAL INFORMATION AND DIAGNOSIS (TBI FOR G10)
DTC P0505 IDLE CONTROL SYSTEM MALFUNCTION
CIRCUIT DESCRIPTION
DTC DETECTING CONDITIONPOSSIBLE CAUSE
DTC will set when A, B or C condition is met.
A: Throttle opening change is small as compared with
electrically live time.
B: Throttle valve opening is not within its target range
with CTP switch ON.
C: Drive voltage exists though ECM (PCM) is not
outputting ISC drive command.
Malajusted accelerater cable

Poor movement of throttle valve

Closed throttle position switch malfunction

Idle speed control actuator malfunction

Idle speed control relay malfunction

“Gr / B”, “Gr / Y”, “Gr”, “Gr / R”, “Gr / G”, “Lg” or “B/Bl”
circuit open or short

Throttle position sensor malfunction

ECM (PCM) malfunction
DTC CONFIRMATION PROCEDURE
1) Turn ignition switch OFF.
2) Clear DTC with ignition switch ON.
3) Start cold engine.
4) Run it idle for 5 min.
5) Select “DTC” mode on scan tool and check DTC.
NOTE:
If engine speed changes up and down when engine speed is increased by opening throttle valve more
than half but not changing its opening, it is possible that closed throttle position switch is malfunction-
ing.

ENGINE GENERAL INFORMATION AND DIAGNOSIS (TBI FOR G10) 6-87
Fig. 1 for Step 3 Fig. 2 for Step 3 Fig. 3 for Step 3
1. ISCA relay
2. Relay box
DTC P0505
INSPECTION
STEPACTIONYESNO
1Was “ENGINE DIAG. FLOW TABLE” performed?Go to Step 2.Go to “ENGINE DIAG.
FLOW TABLE”.
2Check Idle Control System.
1) Connect SUZUKI scan tool to DLC with ignition
switch OFF, set parking brake and block drive
wheels.
2) Warm up engine to normal operating
temperature.
3) Clear DTC and select “MISC TEST” mode on
SUZUKI scan tool.
Is it possible to control (increase and reduce)
engine idle speed by using SUZUKI scan tool?Check TP sensor (Go to
DTC P0121 Flow Table)
If TP sensor is OK,
intermittent trouble or
faulty ECM (PCM).
Check for intermittent
referring to “Intermittent
and Poor Connection”
in Section 0A.Go to Step 3.
3Check ISC Relay.
1) Ignition switch OFF and remove ISC relay
(“ISCA”).
2) Check for proper connection to ISC relay at
terminals 3 and 4.
3) Check resistance between each two terminals.
Between terminals 1 and 2: Infinity
Between terminals 3 and 4: 100 – 120 Ω
4) Check that there is continuity between
terminals 1 and 2 when battery is connected to
terminals 3 and 4.
Is ISC relay in good condition?Go to Step 4.Replace ISC relay.
4Check Idle Speed Control Actuator.
1) Check ISC actuator operation by referring to
ISC ACTUATOR INSPECTION in Section 6.
Is it good condition?Check “Gr / B”, “Gr / Y”,
“Gr” and “Gr / R” circuit
for open and short.
If wires and connections
are OK, substitute a
known-good ECM
(PCM) and recheck.Replace throttle lower
body with ISC actuator.

ENGINE GENERAL INFORMATION AND DIAGNOSIS (TBI FOR G10) 6-89
DTC P0601 INTERNAL CONTROL MODULE MEMORY CHECK SUM ERROR
DTC DETECTING CONDITIONPOSSIBLE CAUSE
DTC P0601: Data write error (or check sum error)
when written into ECM (PCM)
2 driving cycle detection logic, continuous monitoring.ECM (PCM)
DTC CONFIRMATION PROCEDURE
1) Turn ignition switch OFF.
2) Clear DTC with ignition switch ON and then turn ignition switch OFF.
3) Start engine and run it at idle if possible.
4) Check pending DTC in “ON BOARD TEST” or “PENDING DTC” mode and DTC in “DTC” mode.
INSPECTION
Substitute a known-good ECM (PCM) and recheck.

6-92 ENGINE GENERAL INFORMATION AND DIAGNOSIS (TBI FOR G10)
Fig. 1 for Step 1
DTC P1450 BAROMETRIC PRESSURE SENSOR LOW / HIGH INPUT
DTC P1451 BAROMETRIC PRESSURE SENSOR PERFORMANCE PROBLEM
WIRING DIAGRAM / CIRCUIT DESCRIPTION
Barometric pressure sensor is installed in ECM (PCM).
DTC DETECTING CONDITION
POSSIBLE CAUSE
DTC P1450:

Barometric pressure: 136 kPa 1025 mmHg or higher, or
33 kPa 250 mmHg or lower
ECM (PCM) (barometric pressure sensor)
malfunction
DTC P1451:

Vehicle stopped.

Engine cranking.

Difference between barometric pressure and intake
manifold absolute pressure is 26 kPa, 200 mmHg or more.
2 driving cycle detection logic, monitoring once / 1 driving.
Manifold absolute pressure sensor and its
circuit malfunction

ECM (PCM) (barometric pressure sensor)
malfunction
DTC CONFIRMATION PROCEDURE
1) Turn ignition switch OFF.
2) Clear DTC with ignition switch ON.
3) Turn ignition switch ON for 2 sec., crank engine for 2 sec. and run it at idle for 1 min.
4) Check pending DTC in “ON BOARD TEST” or “PENDING DTC” mode and DTC in “DTC” mode.
INSPECTION
DTC P1450:
Substitute a known-good ECM (PCM) and recheck.
DTC P1451:
NOTE:
Note that atmospheric pressure varies depending on weather conditions as well as altitude.
Take that into consideration when performing these check.
STEP
ACTIONYESNO
11) Connect scan tool to DLC with ignition switch
OFF.
2) Turn ignition switch ON and select “DATA
LIST” mode on scan tool.
3) Check manifold absolute pressure. See Fig. 1.
Is it barometric pressure (approx. 100 kPa,
760 mmHg) at sea level?Substitute a known-
good ECM (PCM) and
recheck.Check intake manifold
pressure sensor and its
circuit.
Go to P0105 DIAG.
FLOW TABLE.