idle SUZUKI SWIFT 2000 1.G SF310 Service Workshop Manual

AUTOMATIC TRANSMISSION (3 A / T) (VEHICLE WITH WU-TWC) 7B-15
CUSTOMER PROBLEM INSPECTION FORM (EXAMPLE)
User name:Model:VIN:
Date of issue:Date Reg.Date of problem:Mileage:
PROBLEM SYMPTOMS
Vehicle does not move (R, D, 2, L range)
No upshift automatically ( 1st to 2nd  2nd to 3rd  2 range  D range)
No downshift automatically ( 3rd to 2nd  2nd to 1st  2 range  D range)
No gear change manually ( 1st  2nd  2nd  3rd)
Automatic shift point too high or too low
Excessive gear change shock (1st / 2nd / 3rd / Reverse)
No kickdown
Transmission slipping in (1st / 2nd / 3rd / Reverse)
Others
VEHICLE / ENVIRONMENTAL CONDITION WHEN PROBLEM OCCURS
Environmental Condition
Weather
Temperature Fair  Cloudy  Rain  Snow  Always  Other
(F/C)  Hot  Warm  Cool  Cold  always
Frequency
y
 Always Sometimes ( times / day, month)  Only once  Under certain
condition
Road Urban  Suburb  Highway  Mountainous  Uphill  Downhill
 Tarmacadam  Grave  Other
Vehicle Condition
Engine &
transmission
 Cold / Warming up phase /  Warmed up
Engine speed ( r / min)transmission
condition
Engine s eed ( r / min)
Throttle opening ( Idle / About % / full)
Vehicle
condition
 At stop /  During driving ( Constant speed  Accelerating  Decelerating)
Right hand cornerLeft hand cornerVehicle speed ( km / h Mile / h)condition Right hand corner  Left hand corner  Vehicle s eed ( km / h Mile / h)
 Other
Malfunction Blink  Always ON  Sometimes ON  Always OFF
indicator lamp Good condition
DiagnosticFirst check:  No code  Malfunction code ( )
trouble codeSecond check:  No code  Malfunction code ( )
NOTE:
The above form is a standard sample. It should be modified according to conditions characteristic of each
market.

AUTOMATIC TRANSMISSION (3 A / T) (VEHICLE WITH WU-TWC) 7B-19
Fig. 1 for Step 5. Fig. 2 for Step 5. Fig. 3 for Step 5.
When not using SUZUKI
scan tool:
lever position
Terminal
Selector
AUTOMATIC TRANSMISSION BASIC CHECK
This check is very important for troubleshooting when PCM (ECM) has detected no DTC and no abnormality has
been found in visual inspection. Follow the flow table carefully.
STEPACTIONYESNO
1Was “AUTOMATIC TRANSMISSION DIAG. FLOW TABLE”
performed?Go to Step 2.Go to
“AUTOMATIC
TRANSMISSION
DIAG. FLOW
TABLE”.
2Check A / T Fluid.
Warm transmission to normal operating temperature and check
fluid level and contamination referring to “FLUID LEVEL
CHECK” of “ON-VEHICLE SERVICE” in this section.
Is it in good condition?Go to Step 3.Add or change
fluid.
3Check Fluid Pressure Control Cable.
1) Warm up engine to normal operating temperature.
2) Check fluid pressure control cable for play referring to
“FLUID PRESSURE CONTROL CABLE” of “ON-VEHICLE
SERVICE” in this section.
Is it in good condition?Go to Step 4.Adjust.
4Check Select Cable for Adjustment referring to “SELECT
CABLE” of “ON-VEHICLE SERVICE” in this section.
Is it adjusted correctly?Go to Step 5.Adjust.
5Check Transmission Range Sensor (Switch) Circuit for
Operation.
When using SUZUKI scan tool:
1) Connect SUZUKI scan tool to DLC with ignition switch OFF.
2) Turn ignition switch ON and check transmission range
signal (P, R, N, D, 2 or L) on display when shifting manual
selector to each range. See Fig. 1.
Is applicable range indicated?
When not using SUZUKI scan tool:
1) Turn ignition switch ON.
2) Check voltage at terminals C03-3 C03-4 C03-5 C03-14
Go to Step 6.Go to Step 3 of
DTC P0705
Flow Table.
2) Check voltage at terminals C03-3, C03-4, C03-5, C03-14,
C03-15 and C03-16 for G10 engine model (C02-11, C02-12,
C02-14, C02-15, C02-21 and C02-23 for G13 engine
model) respectively with selector lever shifted to each
range. See Fig. 2.
Taking terminal C03-3 for G10 engine model (C02-11 for
G13 engine model) as an example, is battery voltage
indicated only when selector lever is shifted to “2” range and
0 V for other ranges as shown in Fig. 3?
Check voltage at other terminals likewise, referring to Fig. 3.
Are check results satisfactory?
6Check Engine Idle speed referring to Section 6E1 or 6E2.
Is it in good condition?Go to
“SYMPTOM-TO-
INSPECTION
TABLE” below.Go to Section
6E1 or 6E2.
C03-5
(C02-21)C03-16
(C02-15)C03-4
(C02-12)C03-15
(C02-14)C03-3
(C02-11)C03-14
(C02-23)
PB + V0 V0 V0 V0 V0 V
R0 VB + V0 V0 V0 V0 V
N0 V0 VB + V0 V0 V0 V
D0 V0 V0 VB + V0 V0 V
20 V0 V0 V0 VB + V0 V
L0 V0 V0 V0 V0 VB + V

AUTOMATIC TRANSMISSION (3 A / T) (VEHICLE WITH WU-TWC) 7B-35
ROAD TEST
This test is to check if upshift and downshift take place at specified
speeds while actually driving vehicle on a level road.
WARNING:

Carry out the test in very little traffic area to prevent an ac-
cident.

The test requires 2 persons, a driver and a tester.
1) Warm up engine.
2) With engine running at idle, shift selector lever to D range.
3) i) Accelerate vehicle speed by depressing accelerator pedal
very little (within 4 deg. of throttle valve opening).
ii) Check if upshift takes place from 1st to 2nd at about 18 km / h
(11 mile / h) and from 2nd to 3rd at about 30 km / h (19 mile / h).
iii)
[For G10 Engine Model]
Stop vehicle once. Then start it again and while accelerating
by depressing accelerator pedal fully, check if upshift takes
place from 1st to 2nd at 52 km / h (33 mile / h) and from 2nd to
3rd at 97 km / h (61 mile / h).
[For G13 Engine Model]
Stop vehicle once. Then start it again and while accelerating
by depressing accelerator pedal fully, check if upshift takes
place from 1st to 2nd at 58 km / h (36 mile / h) and from 2nd to
3rd at 110 km / h (69 mile / h).
iv) Stop vehicle again.
v) Start vehicle and keep it running at 25 km / h (15 mile / h) and
then release accelerator pedal completely. 1 or 2 seconds lat-
er, depress accelerator pedal fully and check if downshift
from 2nd to 1st takes place.
vi) Keep vehicle running at 75 km / h (47 miles / h) and in the
same way as in step v), check if downshift from 3rd to 2nd
takes place.
vii) If upshift or downshift fails to take place at each specified
speed in the road test, possible causes for such failure are as
follows. Check each part which is suspected to be the cause.
Condition
Possible causes
No upshift from 1st
to 2nd
1 – 2 shift valve defective

2nd brake solenoid valve defective

PCM defective, or disconnection or
poor connection in electric circuit
No upshift from
2nd to 3rd
2-3 shift valve defective

Direct clutch solenoid valve defective

PCM defective, or disconnection or
poor connection in electric circuit
No downshift from
2nd to 1st or 3rd to
2nd
Throttle position sensor defective

PCM defective, or disconnection or
poor connection in electric circuit