fuel SUZUKI SWIFT 2000 1.G SF310 Service Repair Manual

“IG
COIL
METER”
Main
fuseIgnition
switch
Main
relayTo other circuits
Injector resistor Fuel injector
6-96 ENGINE GENERAL INFORMATION AND DIAGNOSIS (TBI FOR G10)
TABLE B-1 FUEL INJECTOR CIRCUIT CHECK
INSPECTION
STEPACTIONYESNO
1Was “ENGINE DIAG. FLOW TABLE” performed?Go to Step 2.Go to “ENGINE DIAG.
FLOW TABLE”.
2Injector Circuit Check
1) Check injector circuit for short.
Is fuel injected from injector at ignition switch ON?“Y/B” wire shorted to
ground or faulty
injector.
If wire and injector is
as specified
respectively and then
substitute known-
good ECM (PCM) and
recheck.Go to Step 3.
3Injector Check
1) Check injector for fuel Injection referring to FUEL
INJECTOR ON-VEHICLE INSPECTION in
Section 6E1.
Is fuel injected from injector at engine cranking?Go to Step 4.Go to Step 5.
4Injector Leakage Check
1) Check injector for leaks referring to FUEL
INJECTOR ON-VEHICLE INSPECTION in
Section 6E1.
Is it in good condition?Injector and its circuit
are in good condition.Faulty fuel injector.
5Check Injector for Operating Sound.
1) Using sound scope, check injector for operating
sound at engine cranking.
Is it detected?Proceed to DIAG.
FLOW TABLE B-2 and
B-3.Go to Step 6.

6-98 ENGINE GENERAL INFORMATION AND DIAGNOSIS (TBI FOR G10)
Main
fuseIgnition
switchTo other circuits
Main
relay
Fuel pump relay
Fuel pump
CAUTION: Check to make sure that connection is
made between correct terminals. Wrong connection
can cause damage to ECM (PCM), wire harness, etc.
TABLE B-2 FUEL PUMP AND ITS CIRCUIT CHECK
INSPECTION
STEPACTIONYESNO
1Was “ENGINE DIAG. FLOW TABLE” performed?Go to Step 2.Go to “ENGINE
DIAG. FLOW
TABLE”.
2Check Fuel Pump Control System for Operation. See Fig. 1.
Is fuel pump heard to operate for 2 sec. after ignition switch
ON?Fuel pump circuit
is in good
condition.Go to Step 3.
3Check Fuel Pump for Operation.
1) Remove fuel pump relay from relay box with ignition
switch OFF.
2) Check for proper connection to relay at each terminals.
3) If OK, using service wire, connect terminals E28-1 and
E28-2 of relay connector. See Fig. 2.
Is fuel pump heard to operate at ignition switch ON?Go to Step 4.“P”, “B” or “W/Bl”
circuit open or fuel
pump malfunction.
4Check Fuel Pump Relay for Operation.
1) Check resistance between each two terminals of fuel
pump relay. See Fig.3.
Between terminals “1” and “2”: Infinity
Between terminals “3” and “4”: 100 – 120 Ω
2) Check that there is continuity between terminals “1” and
“2” when battery is connected to terminals “3” and “4”. See
Fig. 4.
Is fuel pump relay in good condition?“P/W” circuit open
or poor C02-21
connection.
If wire and
connection are
OK, substitute a
known-good ECM
(PCM) and
recheck.Replace fuel pump
relay.

1. Fuel pump
2. Fuel filter
3. Throttle body
4. Fuel injector
5. Fuel pressure regulator6. Special tool
(Fuel pressure gauge &
3-way joint)
7. Fuel feed line
8. Fuel return line
6-100 ENGINE GENERAL INFORMATION AND DIAGNOSIS (TBI FOR G10)
TABLE B-3 FUEL PRESSURE CHECK
INSPECTION
STEPACTIONYESNO
1Check Fuel Pressure (Refer to Section 6E1 for details).
1) Release fuel pressure from fuel feed line.
2) Install fuel pressure gauge.
3) Check fuel pressure by repeating ignition switch
ON and OFF. See Fig. 1.
Is fuel pressure then 160 – 210 kPa (1.6 – 2.1 kg / cm
2,
22.7 – 29.9 psi)?
Go to Step 2.Go to Step 4.
2Is 90 kPa (0.9 kg / cm2, 12.8 psi) or higher fuel
pressure retained for 1 minute after fuel pump is
stopped at Step 1?Normal fuel pressure.Go to Step 3.
31) Start engine and warm it up to normal operating
temperature.
2) Keep it running at specified idle speed.
Is fuel pressure then within 90 – 140 kPa
(0.9 – 1.4 kg / cm
2, 12.8 – 20.0 psi)?
Normal fuel pressure.
Clogged vacuum
passage for fuel
pressure regulator
or

Faulty fuel pressure
regulator.
4Is there fuel leakage from fuel feed line hose, pipe or
their joint?Fuel leakage from
hose, pipe or joint.Go to Step 10.
5Was fuel pressure higher than specification in Step 1?Go to Step 6.Go to Step 7.
61) Disconnect fuel return hose from throttle body and
connect new return hose to it.
2) Insert the other end of new return hose into
approved gasoline container.
3) Operate fuel pump.
Is specified fuel pressure obtained then?Restricted fuel return
hose or pipe.Faulty fuel pressure
regulator.
7Was no fuel pressure supplied in Step 1?Go to Step 8.Go to Step 9.

ENGINE GENERAL INFORMATION AND DIAGNOSIS (TBI FOR G10) 6-101
Fig. 1 for Step 1
1. Fuel pressure gauge & 3way joint
STEPACTIONYESNO
8With fuel pump operated and fuel return hose
blocked by pinching it, is fuel pressure applied?Faulty fuel pressure
regulator.Shortage of fuel or fuel
pump or its circuit
defective (refer to B-2
FUEL PUMP ANDITS
CIRCUIT CHECK).
91) Operate fuel pump.
2) With fuel return hose blocked by pinching it, check
fuel pressure.
Is it 450 kPa (4.5 kg / cm
2, 63.9 psi) or more?
Faulty fuel pressure
regulator.
Clogged fuel filter,

Restricted fuel feed
hose or pipe,

Faulty fuel pump or

Fuel leakage from
hose connection in
fuel tank.
101) Disconnect fuel return hose from throttle body and
connect new return hose to it.
2) Insert the other end of new return hose into
approved gasoline container.
3) Check again if specified pressure is retained.
While doing so, does fuel come out of return hose?Faulty fuel pressure
regulator.
Fuel leakage from
injector,

Fuel leakage from
between injector
and throttle body,

Faulty fuel pump
(faulty check valve
in fuel pump) or

Fuel leakage from
fuel pressure
regulator
diaphragm.

6-1
ENGINE GENERAL INFORMATION AND DIAGNOSIS (SFI FOR G13) 6-1-1
GENERAL INFORMATION6-1- 3 . . . . . . . . . . . . . .
ENGINE DIAGNOSIS6-1- 6 . . . . . . . . . . . . . . . . . . .
General Description 6-1- 6. . . . . . . . . . . . . . . . . . .
On-Board Diagnostic System 6-1- 6. . . . . . . . . .
Precaution in Diagnosing Trouble 6-1- 9. . . . . . .
Engine Diagnostic Flow Table 6-1-10. . . . . . . . . .
Customer Problem Inspection From 6-1-12. . .
Malfunction Indicator Lamp Check 6-1-13. . . .
Diagnostic Trouble Code Check 6-1-13. . . . . .
Diagnostic Trouble Code Clearance 6-1-14. . .
Diagnostic Trouble Code Table 6-1-15. . . . . . .
Fail-safe Table 6-1-18. . . . . . . . . . . . . . . . . . . . .
Visual Inspection 6-1-19. . . . . . . . . . . . . . . . . . .
Engine Basic Inspection 6-1-20. . . . . . . . . . . . .
Engine Diagnosis Table 6-1-22. . . . . . . . . . . . .
Scan Tool Data 6-1-29. . . . . . . . . . . . . . . . . . . . . . .
Inspection of ECM (PCM) and Its
Circuits 6-1-33. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Voltage Check 6-1-33. . . . . . . . . . . . . . . . . . . . .
Resistance Check 6-1-37. . . . . . . . . . . . . . . . . .
Component Location 6-1-38. . . . . . . . . . . . . . . . . .
Table A-1 MIL Circuit Check
(Lamp does not come on) 6-1-39. . . . . . . . . . . . Table A-2 MIL Circuit Check
(Lamp remains ON) 6-1-40. . . . . . . . . . . . . . . . . .
Table A-3 ECM (PCM) Power and
Ground Circuit Check 6-1-41. . . . . . . . . . . . . . . .
DTC P0105 MAP Circuit Malfunction 6-1-43. . . .
DTC P0110 IAT Circuit Malfunction 6-1-46. . . . .
DTC P0115 ECT Circuit Malfunction 6-1-48. . . .
DTC P0120 Throttle Position Circuit
Malfunction 6-1-50. . . . . . . . . . . . . . . . . . . . . . . . .
DTC P0121 Throttle Position Circuit
Range / Performance Problem 6-1-52. . . . . . . . .
DTC P0130 HO2S Circuit Malfunction
(Sensor-1) 6-1-54. . . . . . . . . . . . . . . . . . . . . . . . . .
DTC P0133 HO2S Circuit Slow
Response (Sensor-1) 6-1-56. . . . . . . . . . . . . . . .
DTC P0134 HO2S Circuit No Activity
Detected 6-1-57. . . . . . . . . . . . . . . . . . . . . . . . . . .
DTC P0135 HO2S Heater Circuit
Malfunction (Sensor-1) 6-1-58. . . . . . . . . . . . . . .
DTC P0136 HO2S Circuit Malfunction
(Sensor-2) 6-1-60. . . . . . . . . . . . . . . . . . . . . . . . . .
DTC P0141 HO2S Heater Circuit
Malfunction (Sensor-2) 6-1-63. . . . . . . . . . . . . . .
DTC P0171 Fuel System Too Lean 6-1-65. . . . .
DTC P0172 Fuel System Too Rich 6-1-65. . . . . .
SECTION 6-1
ENGINE GENERAL INFORMATION
AND DIAGNOSIS
(SFI FOR G13)
WARNING:
For vehicles equipped with Supplemental Restraint (Air Bag) System:

Service on and around the air bag system components or wiring must be performed only by an autho-
rized SUZUKI dealer. Refer to “Air Bag System Components and Wiring Location View” under “Gener-
al Description” in air bag system section in order to confirm whether you are performing service on
or near the air bag system components or wiring. Please observe all WARNINGS and “Service Precau-
tions” under “On-Vehicle Service” in air bag system section before performing service on or around
the air bag system components or wiring. Failure to follow WARNINGS could result in unintentional
activation of the system or could render the system inoperative. Either of these two conditions may
result in severe injury.

Technical service work must be started at least 90 seconds after the ignition switch is turned to the
“LOCK” position and the negative cable is disconnected from the battery. Otherwise, the system may
be activated by reserve energy in the Sensing and Diagnostic Module (SDM).
CONTENTS

6-1-2 ENGINE GENERAL INFORMATION AND DIAGNOSIS (SFI FOR G13)
DTC P0300 Random Misfire
Detected 6-1- 69. . . . . . . . . . . . . . . . . . . . . . . . . .
DTC P0301 Cylinder 1 Misfire
Detected 6-1- 69. . . . . . . . . . . . . . . . . . . . . . . . . .
DTC P0302 Cylinder 2 Misfire
Detected 6-1- 69. . . . . . . . . . . . . . . . . . . . . . . . . .
DTC P0303 Cylinder 3 Misfire
Detected 6-1- 69. . . . . . . . . . . . . . . . . . . . . . . . . .
DTC P0304 Cylinder 4 Misfire
Detected 6-1- 69. . . . . . . . . . . . . . . . . . . . . . . . . .
DTC P0335 CKP Sensor Circuit
Malfunction 6-1- 73. . . . . . . . . . . . . . . . . . . . . . . .
DTC P0340 CMP Sensor Circuit
Malfunction 6-1- 75. . . . . . . . . . . . . . . . . . . . . . . .
DTC P0400 EGR Flow Malfunction 6-1- 78. . . .
DTC P0420 Catalyst System
Efficiency Below Threshold 6-1- 81. . . . . . . . . .
DTC P0443 Purge Control Valve Circuit
Malfunction 6-1- 84. . . . . . . . . . . . . . . . . . . . . . . .
DTC P0480 Radiator Fan Control
System Malfunction 6-1- 85. . . . . . . . . . . . . . . . .
DTC P0500 Vehicle Speed Sensor
Malfunction 6-1- 87. . . . . . . . . . . . . . . . . . . . . . . .
DTC P0505 Idle Control System
Malfunction 6-1- 91. . . . . . . . . . . . . . . . . . . . . . . . DTC P0601 Internal Control Module
Memory Check Sum Error 6-1- 93. . . . . . . . . . .
DTC P1450 Barometric Pressure
Sensor Low / High Input 6-1- 94. . . . . . . . . . . . .
DTC P1451 Barometric Pressure Sensor
Performance Problem 6-1- 94. . . . . . . . . . . . . . .
DTC P1500 Engine Starter Signal
Circuit Malfunction 6-1- 96. . . . . . . . . . . . . . . . . .
DTC P1510 ECM (PCM) Back-up
Power Supply Malfunction 6-1- 97. . . . . . . . . . .
Table B-1 Fuel Injector Circuit Check 6-1- 98. . .
Table B-2 Fuel Pump and Its Circuit
Check 6-1- 99. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table B-3 Fuel Pressure Check 6-1-101. . . . . . . .
Table B-4 A / C Signal Circuits Check 6-1-103. . .
Table B-5 PSP Switch Signal Circuit
Check 6-1-104. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table B-6 Electric Load Signal Circuit
Check 6-1-105. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table B-7 Radiator Cooling Fan Control
System Check 6-1-106. . . . . . . . . . . . . . . . . . . . .
SPECIAL TOOLS6-1-108 . . . . . . . . . . . . . . . . . . . . .

HOSE CONNECTION
Clamp securely at a position 3 to
7mm (0.12–0.27 in.) from hose end. With short pipe, fit hose as far as it reaches pipe joint as
shown.
Hose
Pipe
ClampClamps securely at a position
3 to 7 mm (0.12–0.27 in.)
from hose end.
With following type pipe, fit hose as far as its peripheral
projection as shown.
Clamp securely at a position
3 to 7 mm (0.12–0.27 in.)
from hose end.
With bent pipe, fit hose as its bent part as shown or till pipe
is about 20 to 30 mm (0.79–1.18 in.) into the hose.
Clamp securely at a
position 3 to 7 mm
(0.12–0.27 in.) from hose
end.
With straight pipe, fit hose till pipe is, about 20 to 30 mm
(0.79–1.18 in.) into the hose.
Hose
20 to 30 mm
(0.79–1.18 in.)
Clamp
6-1-4 ENGINE GENERAL INFORMATION AND DIAGNOSIS (SFI FOR G13)
PRECAUTION ON FUEL SYSTEM SERVICE

Work must be done with no smoking, in a well-ventilated area and
away from any open flames.

As fuel feed line (between fuel pump and fuel delivery pipe) is still
under high fuel pressure even after engine was stopped, loosen-
ing or disconnecting fuel feed line directly may cause dangerous
spout of fuel to occur where loosened or disconnected.
Before loosening or disconnecting fuel feed line, make sure to re-
lease fuel pressure according to “FUEL PRESSURE RELIEF
PROCEDURE”. A small amount of fuel may be released after the
fuel line is disconnected. In order to reduce the chance of person-
al injury, cover the fitting to be disconnected with a shop cloth. Put
that cloth in an approved container when disconnection is com-
pleted.

Never run engine with fuel pump relay disconnected when engine
and exhaust system are hot.

Fuel or fuel vapor hose connection varies with each type of pipe.
When reconnecting fuel or fuel vapor hose, be sure to connect
and clamp each hose correctly referring to left figure Hose Con-
nection.
After connecting, make sure that it has no twist or kink.

When installing injector or fuel delivery pipe, lubricate its O-ring
with spindle oil or gasoline.

When connecting fuel pipe flare nut, first tighten flare nut by hand
and then tighten it to specified torque.

ENGINE GENERAL INFORMATION AND DIAGNOSIS (SFI FOR G13) 6-1-5
FUEL PRESSURE RELIEF PROCEDURE
CAUTION:
This work must not be done when engine is hot. If done so,
it may cause adverse effect to catalyst.
After making sure that engine is cold, release fuel pressure as fol-
lows.
1) Place transmission gear shift lever in “Neutral” (Shift selector le-
ver to “P” range for A / T model), set parking brake, and block
drive wheels.
2) Remove relay box cover.
3) Disconnect fuel pump relay (1) from relay box.
4) Remove fuel filler cap to release fuel vapor pressure in fuel tank
and then reinstall it.
5) Start engine and run it till it stops for lack of fuel. Repeat cranking
engine 2-3 times for about 3 seconds each time to dissipate fuel
pressure in lines. Fuel connections are now safe for servicing.
6) Upon completion of servicing, connect fuel pump relay (1) to
relay box and install relay box cover.
FUEL LEAKAGE CHECK PROCEDURE
After performing any service on fuel system, check to make sure
that there are no fuel leakages as follows.
1) Turn ON ignition switch for 3 seconds (to operate fuel pump) and
then turn it OFF.
Repeat this (ON and OFF) 3 or 4 times and apply fuel pressure
to fuel line. (till fuel pressure is felt by hand placed on fuel feed
hose.)
2) In this state, check to see that there are no fuel leakages from
any part of fuel system.

An Example of Freeze Frame Data
1. Trouble Code P0102 (1st)
2. Engine Speed 782 RPM
3. Eng Cool Tmp. 80C
4. Vehicle Spd. 0 km/h
5. MAP Sensor 39 kPa
6. St. Term FT1– 0.8% Lean
7. Lg. Term FT1– 1.6% Lean
8. Fuel 1 Stat. Closed Loop
9. Fuel 2 Stat. Not used
10. Load value 25.5%
1st, 2nd or 3rd in parentheses here represents which
position in the order the malfunction is detected.
ENGINE GENERAL INFORMATION AND DIAGNOSIS (SFI FOR G13) 6-1-7
Warm-up Cycle
A warm-up cycle means sufficient vehicle operation such that the
coolant temperature has risen by at least 22C (40F) from engine
starting and reaches a minimum temperature of 70C (160F).
Driving Cycle
A “Driving Cycle” consists of engine startup and engine shutoff.
2 Driving Cycle Detection Logic
The malfunction detected in the first driving cycle is stored in ECM
(PCM) memory (in the form of pending DTC and freeze frame data)
but the malfunction indicator lamp does not light at this time. It lights
up at the second detection of same malfunction also in the next driv-
ing cycle.
Pending DTC
Pending DTC means a DTC detected and stored temporarily at 1
driving cycle of the DTC which is detected in the 2 driving cycle
detection logic.
Freeze Frame Data
ECM (PCM) stores the engine and driving conditions (in the from
of data as shown at the left) at the moment of the detection of a mal-
function in its memory. This data is called “Freeze frame data”.
Therefore, it is possible to know engine and driving conditions (e.g.,
whether the engine was warm or not, where the vehicle was running
or stopped, where air / fuel mixture was lean or rich) when a mal-
function was detected by checking the freeze frame data. Also,
ECM (PCM) has a function to store each freeze frame data for three
different malfunctions in the order as the malfunction is detected.
Utilizing this function, it is possible to know the order of malfunctions
that have been detected. Its use is helpful when rechecking or diag-
nosing a trouble.
Priority of freeze frame data:
ECM (PCM) has 4 frames where the freeze frame data can be
stored. The first frame stores the freeze frame data of the malfunc-
tion which was detected first. However, the freeze frame data
stored in this frame is updated according to the priority described
below. (If malfunction as described in the upper square “1” below
is detected while the freeze frame data in the lower square “2” has
been stored, the freeze frame data “2” will be updated by the freeze
frame data “1”.)
PRIORITY
FREEZE FRAME DATA IN FRAME 1
1
Freeze frame data at initial detection of malfunction
among misfire detected (P0300-P0304), fuel
system too lean (P0171) and fuel system too rich
(P0172)
2Freeze frame data when a malfunction other than
those in “1” above is detected

B+
Body ground
ECM (PCM) ground
Serial data line
(K line of ISO 9141)
6-1-8 ENGINE GENERAL INFORMATION AND DIAGNOSIS (SFI FOR G13)
In the 2nd through the 4th frames, the freeze frame data of each
malfunction is stored in the order as the malfunction is detected.
These data are not updated.
Shown in the table below are examples of how freeze frame data
are stored when two or more malfunctions are detected.
FRAMEFRAME 1FRAME 2FRAME 3FRAME 4FRAME
MALFUNCTION
DETECTED ORDER
FREEZE FRAME
DATA
to be updated1st FREEZE
FRAME DATA2nd FREEZE
FRAME DATA3rd FREEZE
FRAME DATA
No malfunctionNo freeze frame data
1P0400 (EGR)
detectedData at P0400
detectionData at P0400
detection––
2P0171 (Fuel
system) detectedData at P0171
detectionData at P0400
detectionData at P0171
detection–
3P0300 (Misfire)
detectedData at P0171
detectionData at P0400
detectionData at P0171
detectionData at P0300
detection
4P0301 (Misfire)
detectedData at P0171
detectionData at P0400
detectionData at P0171
detectionData at P0300
detection
Freeze frame data clearance:
The freeze frame data is cleared at the same time as clearance of
diagnostic trouble code (DTC).
Data Link Connector (DLC)
DLC (1) is in compliance with ISO 15031-3 (SAEJ1962) in its instal-
lation position, the shape of connector and pin assignment.
Serial data line (K line of ISO 9141) is used for SUZUKI scan tool
(Tech-1) to communicate with ECM (PCM).