Vacuum hoses SUZUKI SWIFT 2000 1.G SF310 Service Workshop Manual

0A-8 GENERAL INFORMATION

When disconnecting vacuum hoses, attach a tag describing
the correct installation positions so that the hoses can be re-
installed correctly.

After servicing fuel, oil, coolant, vacuum, exhaust or brake
systems, check all lines related to the system for leaks.

For vehicles equipped with fuel injection systems, never dis-
connect the fuel line between the fuel pump and injector
without first releasing the fuel pressure, or fuel can be
sprayed out under pressure.

When performing a work that produces a heat exceeding
80C in the vicinity of the electrical parts, remove the heat
sensitive electrical part(s) beforehand.

Use care not to expose connectors and electrical parts to wa-
ter which will be a cause of a trouble.

ENGINE GENERAL INFORMATION AND DIAGNOSIS (TBI FOR G10) 6-19
Operation
VISUAL INSPECTION
Visually check following parts and systems.
INSPECTION ITEM
REFERRING SECTION

Engine oil ––––– level, leakage

Engine coolant ––––– level, leakage

Fuel ––––– level, leakage

A / T fluid ––––– level, leakage

Air cleaner element ––––– dirt, clogging

Battery ––––– fluid level, corrosion of terminal

Water pump belt ––––– tension, damage

Throttle cable ––––– play, installation

Vacuum hoses of air intake system ––––– disconnection,
looseness, deterioration, bend

Connectors of electric wire harness ––––– disconnection, friction

Fuses ––––– burning

Parts ––––– installation, bolt ––––– looseness

Parts ––––– deformation

Other parts that can be checked visually
Also check following items at engine start, if possible

Malfunction indicator lamp

Charge warning lamp

Engine oil pressure warning lamp

Engine coolant temp. meter

Fuel level meter

Tachometer, if equipped

Abnormal air being inhaled from air intake system

Exhaust system ––––– leakage of exhaust gas, noise

Other parts that can be checked visuallySection 0B
Section 0B
Section 0B
Section 0B
Section 0B
Section 0B
Section 6E1
Section 8
Section 6
Section 6H
Section 8 (section 6 for pressure check)
Section 8
Section 8

ENGINE GENERAL INFORMATION AND DIAGNOSIS (TBI FOR G10) 6-27
ConditionPossible CauseReferring Item
Improper engine
idling or engine
fails to idleIgnition system out of order

Faulty spark plug

Leaky or disconnected high-tension cord

Faulty ignition coil with ignitor
Fuel system out of order

Fuel pressure out of specification

Leaky manifold, throttle body, or cylinder head
gasket
Engine and emission control system out of
order

Faulty idle control system

Faulty evaporative emission control system

Faulty fuel injector

Faulty fuel injector resistor

Poor performance of ECT sensor, TP sensor or
MAP sensor

Faulty ECM (PCM)
Engine overheating
Low compression
Others

Loose connection or disconnection of vacuum
hoses

Malfunctioning PCV valve
Spark plugs in Section 6F
High-tension cords in Section 6F
Ignition coil in Section 6F
Diagnostic Flow Table B-3 in
Section 6
Diagnostic Flow Table P0505
EVAP control system in Section
6E
Diagnostic Flow Table B-1
Fuel injector resistor in Section 6E1
ECT sensor, TP sensor or MAP
sensor in Section 6E1
Refer to “Overheating” section
Previously outlined
PCV system in Section 6E1

ENGINE GENERAL INFORMATION AND DIAGNOSIS (SFI FOR G13) 6-1-19
Operation
VISUAL INSPECTION
Visually check following parts and systems.
INSPECTION ITEM
REFERRING SECTION

Engine oil ––––– level, leakage

Engine coolant ––––– level, leakage

Fuel ––––– level, leakage

A / T fluid ––––– level, leakage

Air cleaner element ––––– dirt, clogging

Battery ––––– fluid level, corrosion of terminal

Water pump belt ––––– tension, damage

Throttle cable ––––– play, installation

Vacuum hoses of air intake system ––––– disconnection,
looseness, deterioration, bend

Connectors of electric wire harness ––––– disconnection, friction

Fuses ––––– burning

Parts ––––– installation, bolt ––––– looseness

Parts ––––– deformation

Other parts that can be checked visually
Also check following items at engine start, if possible

Malfunction indicator lamp

Charge warning lamp

Engine oil pressure warning lamp

Engine coolant temp. meter

Fuel level meter

Tachometer, if equipped

Abnormal air being inhaled from air intake system

Exhaust system ––––– leakage of exhaust gas, noise

Other parts that can be checked visuallySection 0B
Section 0B
Section 0B
Section 0B
Section 0B
Section 0B
Section 6E2
Section 8
Section 6
Section 6H
Section 8 (Section 6 for pressure check)
Section 8
Section 8

ENGINE GENERAL INFORMATION AND DIAGNOSIS (SFI FOR G13) 6-1-27
ConditionPossible CauseReferring Item
Improper engine
idling or engine
fails to idleIgnition system out of order

Faulty spark plug

Leaky or disconnected high-tension cord

Faulty ignition coil with ignitor
Fuel system out of order

Fuel pressure out of specification

Leaky manifold, throttle body, or cylinder head
gasket
Engine and emission control system out of
order

Malfunctioning EGR valve

Faulty idle air control system

Faulty evaporative emission control system

Faulty EGR system

Faulty fuel injector(s)

Poor performance of ECT sensor, TP sensor or
MAP sensor

Faulty ECM (PCM)
Engine overheating
Low compression
Others

Loose connection or disconnection of vacuum
hoses

Malfunctioning PCV valve
Spark plugs in Section 6F
High-tension cords in Section 6F
Ignition coil in Section 6F
Diagnostic Flow Table B-3
EGR system in Section 6E2
Diagnostic Flow Table B-4
EVAP control system in Section
6E2
EGR system in Section 6E2
Diagnostic Flow Table B-1
ECT sensor, TP sensor or MAP
sensor in Section 6E2
Refer to “Overheating” section
Previously outlined
PCV system in Section 6E2

1. Throttle body
1. Throttle body
2. ISC actuator
5. Clamp
6A-6 ENGINE MECHANICAL (G10, 1-CAM 6-VALVES ENGINE)
4) Remove air cleaner assembly.
5) Disconnect the following electric lead wires:

EGR valve

ISC actuator (2)

Ground wires from intake manifold

Fuel injector (4)

TP sensor (3)

EFE heater (5)

Engine coolant temp. gauge
6) Disconnect fuel return (4) and feed hoses (3) from fuel pipes.
7) Disconnect coolant hoses from intake manifold.
8) Disconnect the following vacuum hoses.

Canister purge hose from intake manifold.

EGR pressure transducer hoses from EGR valve.

EGR valve hose from EGR valve.

Pressure sensor hose from intake manifold.

Brake booster hose from intake manifold.
9) Disconnect breather hose from PCV valve.
10) Disconnect accelerator cable from throttle body.
11) Disconnect other connected to throttle body and intake man-
ifold, if any.
12) Remove intake manifold with throttle body from cylinder head.
13) Remove throttle body from intake manifold.

2. Ground
1. Throttle body
2. ISC actuator
coupler
3. TP sensor
coupler
4. Fuel injector
coupler
5. EFE heater
coupler
ENGINE MECHANICAL (G10, 1-CAM 6-VALVES ENGINE) 6A-7
INSTALLATION
1) Install throttle body to intake manifold. (Refer to Section 6E.)
2) Install intake manifold gasket to cylinder head. Use a new gas-
ket.
3) Install intake manifold (1) with throttle body to cylinder head.

Install clamps (3) as shown in figure, and tighten bolts and
nuts to specification.
Tightening Torque
(a): 23 N
.m (2.3 kg-m, 17.0 lb-ft)
4) Connect breather hose to PCV valve.
5) Connect vacuum hoses.
6) Connect coolant hoses.
7) Connect fuel return and feed hoses to throttle body.
8) Connect electric lead wire.
9) Connect accelerator cable to throttle body.
10) Install air cleaner assembly to throttle body.
11) Check to ensure that all removed parts are back in place.
Reinstall any necessary parts which have not been reinstalled.
12) Refill cooling system.
13) Connect negative cable at battery.
14) Upon completion of installation, start engine and check for fuel
leaks and engine coolant leaks.
After warming up engine, adjust accelerator cable play to spec-
ification according to description in Section 6E.

6A-24 ENGINE MECHANICAL (G10, 1-CAM 6-VALVES ENGINE)
UNIT REPAIR OVERHAUL
ENGINE ASSEMBLY
REMOVAL
1) Relieve fuel pressure according to procedure described in
“FUEL PRESSURE RELIEF PROCEDURE” of Section 6.
2) Remove engine hood after disconnecting front window washer
hose.
3) Disconnect battery cables at battery and remove battery and
its tray.
4) Drain cooling system.
5) Remove air cleaner assembly.
6) Remove radiator with cooling fan. Refer to Section 6B for re-
moval.
7) Disconnect the following electric wire harness.

High-tension cord from ignition coil

Distributor

EGR valve

ECT sensor

ISC actuator

Ground wire harness from intake manifold

TP sensor

Fuel injector

Oil pressure gauge

A / C compressor pressure switch (if equipped)

Heated oxygen sensor

Generator

Starter

Back-up light switch (For M / T model)

Battery negative cable from transmission

Shift switch of A / T (For A / T model)

Direct clutch and 2nd brake solenoids of A / T (For A / T model)

Vehicle speed sensor on A / T (For A / T model)
And release above wire harness from clamps.
8) Disconnect the following vacuum hose.

Brake booster hose from intake manifold.

Canister purge hose from EVAP canister purge valve.

Pressure sensor hose from intake manifold.
9) Disconnect fuel return hose and fuel feed hose from fuel feed
and return pipes.
10) Disconnect heater inlet and outlet hoses.

6A1-6 ENGINE MECHANICAL (G13B, 1-CAM 16-VALVES ENGINE)
ENGINE VACUUM CHECK
The engine vacuum that develops in the intake line is a good indica-
tor of the condition of the engine. The vacuum checking procedure
is as follows:
1) Warm up engine to normal operating temperature.
NOTE:
After warming up engine, place transmission gear shift le-
ver in “Neutral” (shift selector lever to “P” range for A / T
model), and set parking brake and block drive wheels.
2) With engine stopped, disconnect EVAP canister purge valve
hose from intake manifold and connect 3-way joint, hoses and
special tools (vacuum gauge and joint) between intake manifold
and vacuum hose disconnected.
Special Tool
(A): 09915-67311
(B): 09918-08210
SUZUKI GENUINE PARTS
(C): Hose 09343-03087
(D): 3-way joint 09367-04002
3) Run engine at specified idle speed, and read vacuum gauge.
Vacuum should be within the following specification.
Vacuum specification (at sea level):
52.6 – 65.8 kPa (40 – 50 cm
Hg, 15.7 – 19.7 in.Hg) at specified
idling speed
4) After checking, connect vacuum hose to intake surge tank.

6E1-12 ENGINE AND EMISSION CONTROL SYSTEM (TBI FOR G10)
1. Fuel injector wire
2. Fuel injector
3. Upper O-ring
4. Lower O-ring
5. Throttle upper body
6. Gasket
7. Throttle lower body
8. ISC actuator
9. TP sensor
10. Injector sub wire coupler
11. O-ring
12. Injector wire cover
CAUTION:
As throttle stop screw and throttle lever screw are fac-
tory adjusted precisely, don’t remove or adjust them.
Throttle
stop
screw
Throttle lever
screwPositive
terminal Negative
terminal
Viewed from “A”
1. Throttle body
2. Vacuum nozzle
1. Injector coupler
2. TP sensor
3. Water hose
4. Vacuum hose
5. ISC actuator
6. Fuel return hose
7. Fuel feed hose
THROTTLE BODY
ON-VEHICLE INSPECTION

Check that throttle valve lever moves smoothly.

Vacuum passage inspection.
With fingers placed against vacuum nozzle, increase engine
speed a little and check that vacuum is applied.
REMOVAL
1) Relieve fuel pressure, referring to Section 6.
2) Disconnect battery negative cable at battery.
3) Remove air cleaner assembly referring to Section 6A.
4) Drain cooling system.
5) Disconnect following wire harness couplers:

TP sensor

Fuel injector

ISC actuator
6) Disconnect following hoses from throttle body.

Fuel feed and return hoses

Engine cooling water hoses

Vacuum hoses
7) Disconnect accelerator cable from throttle valve lever and cable
bracket.
8) Remove throttle body from intake manifold.