clutch SUZUKI SWIFT 2000 1.G Transmission Service Repair Manual

CLUTCH 7C-11
4) Slightly apply grease to input shaft (1), then join transmission
assembly with engine. Refer to Section 7A for remounting
procedure.
“A” : Grease, 99000-25210
CLUTCH RELEASE SYSTEM
REMOVAL
1) Remove release lever by loosening its bolt.
2) Take out release bearing by turning release shaft (1).
3) Unhook return spring by using pliers.
4) Drive out No.2 bush by using special tool and hammer.
Release shaft seal will also be pushed out.
Special tool
(A) : 09922-46010
5) Remove release shaft and return spring.
6) Install tap (M16 X 1.5) (1) to clutch release shaft No.1 bush.
7) Pull out No.1 bush by using tap (1) and special tools.
Special tool
(B) : 09923-46020
(C) : 09930-30104 NOTE:
When inserting transmission input shaft to clutch disc,
turn crankshaft little by little to match splines.

7C-12 CLUTCH
INSPECTION
Clutch release bearing
Check clutch release bearing for smooth rotation.
If abnormality is found, replace it.
Clutch release shaft
Check clutch release shaft and its pin for deflection or damage.
If abnormality is found, replace it.
INSTALLATION
1) Drive in a new No.1 bush by using special tools and then
apply grease to bush inside.
Special tool
(A) : 09930-30104
(B) : 09923-46030
“A” : Grease 99000-25010
2) Install release shaft with return spring applied to it.CAUTION:
Do not wash release bearing. Washing may cause grease
leakage and consequential bearing damage.

CLUTCH 7C-13
3) Apply grease to No.2 bush (1) inside and press-fit it by using
the same special tool as in removal.
“A” : Grease 99000-25010
Special tool
(C) : 09922-46010
4) Coat grease to shaft seal (2) lip and then install it till it is flush
with case surface. Use special tool for this installation and
face seal lip downward (inside).
“A” : Grease 99000-25010
Special tool
(D) : 09925-98221
5) Caulk seal at A by using caulking tool and hammer.
6) Hook return spring.
7) Apply grease to release bearing (1) inside and release shaft
arm (2), then set bearing.
“A” : Grease 99000-25010
8) Apply small amount of grease to input shaft (3) spline (0.3 g)
and front end (0.15 g) as well.
“B” : Grease 99000-25210
9) Set release lever to release shaft aligning their punch marks
(1), then tighten bolt.
Tightening torque
Release lever bolt (a) : 23 N·m (2.3 kg-m, 16.5 lb-ft)

7C-14 CLUTCH
TIGHTENING TORQUE SPECIFICATION
REQUIRED SERVICE MATERIAL
SPECIAL TOOL
Fastening partTightening torque
Nm kg-m lb-ft
Flywheel bolts 70 7.0 50.5
Clutch cover bolts 23 2.3 16.5
Release lever bolt 23 2.3 16.5
MaterialRecommended SUZUKI product
(Part Number)Use
Lithium grease SUZUKI SUPER GREASE A
(99000-25010)Cable end hook and joint pin.
Release shaft bushes and seal.
Release shaft arm.
Release bearing inside.
SUZUKI SUPER GREASE I
(99000-25210)Input shaft spline and front end.
09921-26020 09922-46010 09923-36320 09923-46020
Bearing remover Bush remover Clutch center guide Joint pipe
09923-46030 09924-17810 09925-98210 09925-98221
Joint pipe Flywheel holder Input shaft bearing
installerBearing installer

CLUTCH 7C-15
09930-30104
Sliding shaft

7C-16 CLUTCH