wheel SUZUKI SX4 2006 1.G Service Workshop Manual
[x] Cancel search | Manufacturer: SUZUKI, Model Year: 2006, Model line: SX4, Model: SUZUKI SX4 2006 1.GPages: 1556, PDF Size: 37.31 MB
Page 613 of 1556
Downloaded from www.Manualslib.com manuals search engine ABS: 4E-8
Component Location
ABS Components LocationS6RW0D4503001
Diagnostic Information and Procedures
ABS CheckS6RW0D4504001
Refer to the following items for the details of each step.
1
2
6
2
6
26
264
5
7
3
8
I5RW0A450006-02
1. ABS hydraulic unit / control module assembly 5. EBD warning light (Brake warning light)
2. Wheel speed sensors 6. Wheel speed sensor encoder (included in wheel hub assembly)
3. Brake light switch 7. Data link connector
4. ABS warning light 8. G sensor (4WD model)
Step Action Yes No
1 ) Malfunction analysis
1) Perform “Customer complaint analysis: ”.
2) Perform “Problem symptom confirmation: ”.
3) Perform “DTC check, record and clearance: ” and
recheck DTC.
Is there any malfunction DTC?Go to Step 4. Go to Step 2.
2 ) Driving test
1) Perform “Step 2: Driving Test: ”.
Is trouble symptom identified?Go to Step 3. Go to Step 6.
3 ) DTC check
1) Perform “DTC Check”.
Is it malfunction code?Go to Step 4. Go to Step 5.
4 ) ABS check
1) Inspect and repair referring to applicable DTC flow.
Does trouble recur?Go to Step 5. Go to Step 7.
5 ) Brakes diagnosis
1) Inspect and repair referring to “Brakes Symptom
Diagnosis in Section 4A”.
Does trouble recur?Go to Step 3. Go to Step 7.
Page 616 of 1556
Downloaded from www.Manualslib.com manuals search engine 4E-11 ABS:
DTC CheckS6RW0D4504004
1) Turn ignition switch to OFF position.
2) Connect SUZUKI scan tool to data link connector
(1).
Special tool
(A): SUZUKI scan tool
3) Turn ignition switch to ON position.
4) Read DTC according to instructions displayed on
SUZUKI scan tool and print it or write it down. Refer
to SUZUKI scan tool operator’s manual for further
details.
NOTE
If SUZUKI scan tool can not communicate
ABS hydraulic unit / control module, perform
“Serial Data Link Circuit Check”.
5) After completing the check, turn ignition switch off
and disconnect SUZUKI scan tool from DLC.
DTC TableS6RW0D4504005
CAUTION!
Be sure to perform “ABS Check” before
starting diagnosis.
DTC ClearanceS6RW0D4504006
WARNING!
When performing a driving test, select a safe
place where there is neither any traffic nor
any traffic accident possibility and be very
careful during testing to avoid occurrence of
an accident.
After repair or replace malfunction part(s), clear all DTCs
by performing the following procedure or using SUZUKI
scan tool.
1) Connect SUZUKI scan tool to data link connector in
the same manner as when making this connection
for DTC check.
2) Turn ignition switch to ON position.
3) Erase DTC according to instructions displayed on
scan tool. Refer to scan tool operator’s manual for
further derails.
NOTE
For DTC C1022, C1026, C1032, C1036 and
C1061, confirm that ABS warning light turns
off after performing Step 2 of “Test Driving”
under “ABS Check”, and then clear the DTCs.
4) After completing the clearance, turn ignition switch
OFF and disconnect scan tool from data link
connector.
5) Perform “Driving Test” (Step 2 of “ABS Check”) and
“DTC Check” and confirm that NO DTC is displayed
on scan tool. DTC (displayed on
SUZUKI scan tool)Diagnostic Items
NO DTC Normal
)C1013 Control module mismatch
) C1015 G sensor circuit (for 4WD model)
)C1016 Brake light switch
)C1021 RF
Wheel speed sensor circuit )C1025 LF
)C1031 RR
)C1035 LR
)C1022 RF
Wheel speed sensor or
encoder )C1026 LF
)C1032 RR
)C1036 LR
)C1033 Wheel speed sensor deviation
(A)
1
I5RW0A450007-01
)C1041 RF
Inlet solenoid )C1045 LF
)C1051 RR
)C1055 LR
)C1042 RF
Outlet solenoid )C1046 LF
)C1052 RR
)C1056 LR
) C1057Power supply voltage too high / too
low
) C1061 Pump motor circuit
) C1063Solenoid valve power supply driver
circuit
) C1071 Control module internal defect DTC (displayed on
SUZUKI scan tool)Diagnostic Items
Page 617 of 1556
Downloaded from www.Manualslib.com manuals search engine ABS: 4E-12
Scan Tool DataS6RW0D4504007
The parameter data below are values measured with the
scan tool when the normally operating vehicle is under
the following conditions. When taking measurements for
comparison by using the scan tool, be sure to check that
the vehicle is under the following conditions.
• Apply parking brake and block wheels.
• Ignition switch ON.
• Turn OFF air conditioner (if equipped).
• Apply no load to power steering (if equipped). (Don’t
turn it)
• Turn OFF all electric loads (except ignition).
• No DTC.
• ABS is not operated. (Normal braking operation)Scan Tool Data Definition
Battery Volt (V)
Battery Voltage is an analog input signal read by the
ABS control module. Certain ABS control module
functions will be modified if the battery voltage falls
below or rises above programmed thresholds.
Pump Motor Driver (V)
This parameter indicates the operational condition of the
pump motor driver (transistor).
RF Wheel Speed, LF Wheel Speed, RR Wheel Speed
and LF Wheel Speed (km/h, MPH)
Wheel speed is an ABS control module internal
parameter. It is computed by reference pulses from the
wheel speed sensor.
Brake Switch (ON, OFF)
This switch signal informs the ABS control module
whether the brake is active or not.
G Sensor (G)
4WD model: Vehicle acceleration is measured by G
sensor and output to ABS control module as the linear
voltage.
2WD model: Fixed 2.54 G.
Solenoid Valve Power Supply Driver (ON, OFF)
ABS control module monitor the supply voltage to
solenoid valve power supply driver. If the voltage is
supplied, ON is displayed. Beside, OFF is displayed.
Inlet Solenoid RF, Inlet Solenoid LF, Inlet Solenoid
RR, Inlet Solenoid LR (ON, OFF)
This parameter indicates the operational condition of the
inlet solenoid valve.
Outlet Solenoid RF, Inlet Solenoid LF, Inlet Solenoid
RR, Inlet Solenoid LR (ON, OFF)
This parameter indicates the operational condition of the
outlet solenoid valve. Scan Tool
DataStandards Condition
) Battery
Voltage10.0 – 16.0 V —
) Pump
Motor Driver0.0 V —
) RF Wheel
Speed0 km/h, 0.0 MPH Vehicle stop
) LF Wheel
Speed0 km/h, 0.0 MPH Vehicle stop
) RR Wheel
Speed0 km/h, 0.0 MPH Vehicle stop
) LR Wheel
Speed0 km/h, 0.0 MPH Vehicle stop
) Brake
SwitchONBrake pedal
depressed
OFFBrake pedal
released
) G sensor0.00G
(4WD model)Place vehicle on the
level
2.54G
(2WD model)Place vehicle on the
level
) Solenoid
Valve Power
Supply DriverON Ignition switch ON
) Inlet
SolenoidRF
OFF Vehicle stop LF
RR
LR
) Outlet
SolenoidRF
OFF Vehicle stop LF
RR
LR
Page 626 of 1556
Downloaded from www.Manualslib.com manuals search engine 4E-21 ABS:
DTC C1015: G Sensor Circuit (4WD Model)S6RW0D4504013
Wiring Diagram
Refer to “Wiring Diagram” under “DTC C1013: Control Module Mismatch”.
DTC Detecting Condition and Trouble Area
NOTE
When a vehicle is lifted up and its wheel(s) is turned, this DTC is set.
In such case, clear the DTC and check again.
Troubleshooting DTC Detecting Condition Trouble Area
• G sensor signal voltage is out of specified range.
• Vehicle behavior and G sensor signal is disagreed.• G sensor
• G sensor circuit
• ABS control module
Step Action Yes No
1Was “ABS Check” performed?Go to Step 2. Go to “ABS Check”.
2Is G sensor installed its bracket securely?Go to Step 3. Tighten G sensor bolt
and recheck.
3G sensor check
1) Disconnect G sensor connector and ABS hydraulic unit /
control module connector with ignition switch turned
OFF.
2) Check for proper connection to G sensor connector and
ABS hydraulic unit / control module terminals of “E08-3”
and “E08-6”.
3) If OK then check G sensor referring to “G Sensor
Inspection (4WD Model)”.
Is it in good condition?Go to Step 4. Replace G sensor.
4G sensor power source voltage check
1) Turn ignition switch to ON position and measure voltage
between “GRN/ORN terminal of G sensor connector and
vehicle body ground.
Is it 10 – 14 V?Go to Step 5. “GRN/ORN” circuit
open.
5G sensor signal circuit and ground circuit check
1) Measure resistance between following terminals.
• Between “E08-3” terminal and “GRN/BLK” terminal of
G sensor.
• Between “E08-6” terminal and “GRN/YEL” terminal of
G sensor.
Is each resistance less than 2
Ω?Go to Step 6. “GRN/BLK” and/or
“GRN/YEL” wire circuits
in open or high
resistance.
6G sensor ground circuit check
1) Connect ABS hydraulic unit / control module connector
with ignition switch turned OFF.
2) Turn ignition switch to ON position and measure voltage
between “GRN/BLK” terminal of G sensor connector and
vehicle body ground.
Is it 0 V?Substitute a known-
good ABS hydraulic unit
/ control module
assembly and recheck.“GRN/BLK” circuit to
power circuit.
Page 627 of 1556
Downloaded from www.Manualslib.com manuals search engine ABS: 4E-22
DTC 1016: Brake Light SwitchS6RW0D4504014
Wiring Diagram
DTC Detecting Condition and Trouble Area
NOTE
When a vehicle is lifted up and its wheel(s) is turned, this DTC is set.
In such case, clear the DTC and check again.
Troubleshooting
WHTGRN
34 712V
E08-7
E08-9GRN/ORN
2
8
112V
GRN/WHT
WHTGRN[A]E08
1
2
3
4
5
6
7 12
13
14
15
16
17
18
19
20
21
228
9
10
11
23
24
25
26
I7RW01450006-05
[A]: ABS control module connector (viewed from terminal side) 3. Ignition switch 6. Brake light
1. Battery 4. Junction block assembly 7. ABS hydraulic unit / control module assembly
2. Main fuse box 5. Brake light switch 8. To ECM and shift lock relay (A/T model)
DTC Detecting Condition Trouble Area
Brake light switch signal voltage becomes 4.8 – 8.0 V for
specified time.• Brake light circuit
• Brake light switch
• ABS control module
Step Action Yes No
1Was “ABS Check” performed?Go to Step 2. Go to “ABS Check”.
2Brake light operation check
1) Turn ignition switch to ON position and depress brake
pedal.
Does brake light turn ON?Go to Step 3. Repair brake light
switch, brake light and/
or brake light circuit and
recheck.
3Brake light switch signal circuit check
1) Disconnect ABS hydraulic unit / control module and
brake light switch connector with ignition switch turned
OFF.
2) Check for proper connection to “E08-7” terminal of ABS
hydraulic unit / control module and “GRN/WHT” wire
terminal of brake light switch.
3) If OK then measurer resistance between terminal of
“E08-7” and “GRN/WHT” wire terminal of brake light
switch connector.
Is it less than 2
Ω?Substitute a known-
good ABS hydraulic unit
/ control module and
recheck.“GRN/WHT” wire open
or high resistance.
Page 628 of 1556
Downloaded from www.Manualslib.com manuals search engine 4E-23 ABS:
DTC C1021 / C1022 / C1025 / C1026 / C1031 / C1032 / C1035 / C1036: Wheel Speed Sensor Circuit /
Sensor or Encoder
S6RW0D4504015
DTC C1021 / C1025 / C1031 / C1035: Right-Front / Left-Front / Right-Rear / Left-Rear Wheel Speed
Sensor Circuit
DTC C1022 / C1026 / C1032 / C1036: Right-Front / Left-Front / Right-Rear / Left-Rear Wheel Speed
Sensor or Encoder
Wiring Diagram
DTC Detecting Condition and Trouble Area
NOTE
When the vehicle was operated in any of the following ways, one of these DTCs may be set even when
the sensor is in good condition. If such possibility is suspected, clear DTC once referring to “DTC
Clearance” and after performing the driving test as described in Step 2 of “ABS Check”, check
whether or not any abnormality exists.
• The vehicle was driven with parking brake pulled.
• Wheel spin occurred while driving.
• Wheel(s) was turned while the vehicle was jacked up.
• The vehicle was stuck.
E08 [A]
1
2
3
4
5
6
7 12
13
14
15
16
17
18
19
20
21
228
9
10
11
23
24
25
26
WHTGRNGRN/ORN
3
4
E08-9
9
12V
8
7
6
5
BLKWHT
BLKWHT
REDRED/BLK
LT GRN/BLKLT GRN
E08-22 E08-11
E08-10 E08-21
E08-23BLK
12V
12V
12V
12V
BLKWHT
BLKWHTWHTWHT/BLK
E08-17 E08-18
YELBRN
E08-19 E08-20
12
I7RW01450007-03
[A]: ABS control module connector (viewed from terminal
side)4. Junction block assembly 8. Right-rear wheel speed sensor
1. Battery 5. Left-front wheel speed sensor 9. ABS hydraulic unit / control module assembly
2. Main fuse box 6. Right- front wheel speed sensor
3. Ignition switch 7. Left-rear wheel speed sensor
DTC Detecting Condition Trouble Area
C1021, C1025, C1031, C1035:
Wheel speed sensor circuit is opened, shorted to power,
ground and/or each other circuit.
C1022, C1026, C1032, C1036:
• Wheel speed is different from other wheel speed
(vehicle speed) for more than specified time.
• Abnormal wheel speed sensor signal is detected for
more than specified time.• Wheel speed sensor
• Wheel speed sensor circuit
• Wheel encoder
• ABS control module
Page 629 of 1556
Downloaded from www.Manualslib.com manuals search engine ABS: 4E-24
DTC Troubleshooting
Step Action Yes No
1Was “ABS Check” performed?Go to Step 2. Go to “ABS Check”.
2Check tire condition
1) Check that tire pressure is specifications.
Are they in good condition?Go to Step 3. Replace tire or adjust
tire pressure and
recheck.
3Wheel speed sensor circuit check
1) Disconnect ABS hydraulic unit / control module
connector and applicable wheel speed sensor connector
with ignition switch turned OFF.
2) Check for proper connection to ABS hydraulic unit /
control module connector at applicable terminals and
terminals of applicable wheel speed sensor.
3) If OK then check applicable wheel speed sensor circuit
for open, short and high resistance.
Is each applicable wheel speed sensor circuit in good
condition?Go to Step 4. Repair circuit and
recheck
4Wheel speed sensor check
1) Inspection applicable wheel speed sensor referring to
“Front and Rear Wheel Speed Sensor Inspection”.
Is it in good condition?Go to Step 5. Clean or replace.
5Wheel speed sensor encoder check
1) Inspection applicable wheel speed sensor encoder
referring to “Front Wheel Speed Sensor Encoder On-
Vehicle Inspection” and/or “Rear Wheel Speed Sensor
Encoder On-Vehicle Inspection”.
Is it in good condition?Go to Step 6. Clean or replace wheel
hub assembly.
6Wheel speed sensor signal check
1) Inspection applicable wheel speed sensor referring to
“Front and Rear Wheel Speed Sensor On-Vehicle
Inspection”.
Is it in good condition?Substitute a known-
good wheel hub
assembly and recheck.
If DTC detected,
substitute a known-
good ABS hydraulic unit
/ control module and
recheck.Replace wheel speed
sensor and recheck.
Page 630 of 1556
Downloaded from www.Manualslib.com manuals search engine 4E-25 ABS:
DTC C1033: Wheel Speed Sensor DeviationS6RW0D4504016
Wiring Diagram
Refer to “Wiring Diagram” under “DTC C1021 / C1022 / C1025 / C1026 / C1031 / C1032 / C1035 / C1036: Wheel
Speed Sensor Circuit / Sensor or Encoder”.
DTC Detecting Condition and Trouble Area
DTC Troubleshooting DTC Detecting Condition Trouble Area
• Three or more sensor signals seem to be effected by
temporary failure suspicion at the same time.
• One wheel or more are controlled by ABS for more than
specified time.• Wheel speed sensor
• Wheel speed sensor circuit
• Wheel encoder
• ABS control module
• Tire (flat tire)
Step Action Yes No
1Was “ABS Check” performed?Go to Step 2. Go to “ABS Check”.
2Check DTC for ABS
1) Connect scan tool to DLC with ignition switch turned
OFF.
2) Turn ignition switch ON and check DTC for ABS.
Is DTC C1021, C1022, C1025, C1026, C1031, C1032,
C1035 and/or C1036 detected together?Go to “DTC C1021 /
C1022 / C1025 / C1026
/ C1031 / C1032 /
C1035 / C1036: Wheel
Speed Sensor Circuit /
Sensor or Encoder” and
recheck.Go to Step 3.
3Check tire condition
1) Check that tire pressure is specifications.
Are they in good condition?Go to Step 4. Replace tire or adjust
tire pressure and
recheck.
4Wheel speed sensor circuit check
1) Disconnect ABS hydraulic unit / control module
connector and all wheel speed sensor connectors with
ignition switch turned OFF.
2) Check for proper connection to ABS hydraulic unit /
control module connector and terminals of wheel speed
sensor.
3) If OK then check all wheel speed sensors circuit for
open, short and high resistance.
Are wheel speed sensor circuits in good condition?Go to Step 5. Repair circuit and
recheck.
5Wheel speed sensor check
1) Inspection all wheel speed sensors referring to “Front
and Rear Wheel Speed Sensor Inspection”.
Are they in good condition?Go to Step 6. Clean or replace.
6Wheel speed sensor encoder check
1) Inspection all wheel speed sensor encoders referring to
“Front Wheel Speed Sensor Encoder On-Vehicle
Inspection” and “Rear Wheel Speed Sensor Encoder
On-Vehicle Inspection”.
Are they in good condition?Go to Step 7. Clean or replace wheel
hub assembly.
7Wheel speed sensor signal check
1) Inspection all wheel speed sensors referring to “Front
and Rear Wheel Speed Sensor On-Vehicle Inspection”.
Are they in good condition?Substitute a known-
good wheel hub
assembly and recheck.
If DTC detected,
substitute a known-
good ABS hydraulic unit
/ control module and
recheck.Replace wheel speed
sensor and recheck.
Page 636 of 1556
Downloaded from www.Manualslib.com manuals search engine 4E-31 ABS:
Troubleshooting
Repair Instructions
ABS Hydraulic Unit Operation CheckS6RW0D4506001
1) Check that basic brake system other than ABS is in
good condition.
2) Check that battery voltage is 11 V or more.
3) Hoist vehicle.
4) Set transmission to neutral (P range for A/T) and
release parking brake.
5) Turn each wheel gradually by hand to check if brake
dragging occurs. If it does, correct.
6) Connect SUZUKI scan tool to data link connector
(DLC) (1) with ignition switch OFF.
Special tool
(A): SUZUKI scan tool Step Action Yes No
1Check fuse
Are main fuses and circuit fuses for ABS in good condition?Go to Step 2. Replace fuse and check
for short circuit to
ground.
2Check ABS control module power supply circuit
1) Turn ignition switch to OFF position.
2) Disconnect ABS control module connector.
3) Check for proper connection to ABS control module
connector at terminals “E08-9”, “E08-23”, “E08-24”, and
“E08-25”.
4) If OK, then turn ignition switch to ON position and
measure voltage between terminal “E08-9” and vehicle
body ground.
Is it 10 – 14 V?Go to Step 3. “GRN/ORN” circuit
open.
3Pump motor and solenoid valve power supply circuit
1) Turn ignition switch to OFF position.
2) Measure voltage between each terminal of “E08-24”,
“E08-25” and vehicle body ground.
Are they 10 – 14 V?Go to Step 4. “WHT/BLU” and/or
“WHT/RED” circuit
open.
4Check ABS hydraulic unit / control module assembly
ground circuit
1) Measure resistance between terminal “E08-23” and
vehicle body ground.
Is resistance less than 2
Ω?ABS hydraulic unit /
control module
assembly power and
ground circuits are in
good condition.“BLK” circuit open or
high resistance.
(A)
1
I5RW0A450007-01
Page 637 of 1556
Downloaded from www.Manualslib.com manuals search engine ABS: 4E-32
7) Turn ignition switch to ON position and select menu
to “HYDRAULIC CONTROL TEST” under
“miscellaneous test” (“MISC. TEST”) mode of
SUZUKI scan tool.
8) Perform the following checks with help of another
person.
Brake pedal (1) should be depressed and then select
testing wheel by SUZUKI scan tool and the wheel (2)
should be turned by another person’s hand. At this
time, check that:
• Operation sound of solenoid is heard and the
wheel turns only about 0.5 sec. (Brake force is
depressurized).
• Operation sound of pump motor is heard and
pulsation is felt at brake pedal.9) Check for all 4-wheels condition respectively. If a
faulty condition is found, replace ABS hydraulic unit /
control module assembly.
10) After completing the check, turn ignition switch to
OFF position and disconnect SUZUKI scan tool from
DLC.
ABS Hydraulic Unit / Control Module Assembly ComponentsS6RW0D4506002
CAUTION!
Never disassemble ABS hydraulic unit / control module assembly, loosen blind plug or remove motor.
Performing any of these prohibited services will affect original performance of ABS hydraulic unit /
control module assembly.
I4RH01450021-01
I6RW0C450006-01
1. ABS hydraulic unit / control module assembly : 16 N⋅m (1.6 kgf-m, 11.5 lb-ft) : 26 N⋅m (2.6 kgf-m, 19.0 lb-ft)
2. Bracket : 9 N⋅m (0.9 kgf-m, 6.5 lb-ft)