fuse box connector SUZUKI SX4 2006 1.G Service Repair Manual

Downloaded from www.Manualslib.com manuals search engine 9A-55 Wiring Systems:
(Continued)
BCM (J/B side connector)
3
4
1
25
15 14 12
13 10
11 9 8 67
17
16182122 19
20
23
1234578 116
12 91034 652 1
G271 G273
G272
10
11 12 13 14 15 16 17 18 19123456789
20
345612L312
23414
3
561214 11
10
157 2 11316 9 8 6
5 4 3
2
1
7
11 10
9 8
15
14 13
1216
L313
L315 E325
2 1
123456789
15 16 17 18 11 10 12 13 14 1
234
5
678 910
E323
L314 E324
E323 E325E324 BCM G272G271 G273 L312 L313 L314 L315
9
J/B
11
13
12
3
1
4
1
4
1
3
16
ACC 1
ACC 25ACC 1
ACC 2
IG2 SW
R-WIP RLYSPARE-1
F-WIP
F-WIP (RLY)
P/W
IG SW (+B)
R-WIP (CONT)
R-WIP (-)
ACC
P/W15A
ACC 2 15A
30A
WIP 30A
(Continued)
23
24
25
20R-WASHERRR WIP 15A19
42
Individual circuit fuse box No.2 (In J/B)
5ACC SW
4
4 3
2
1
Connector No. / Terminal No.
6
IG2
I6RW0C910931-01

Downloaded from www.Manualslib.com manuals search engine Wiring Systems: 9A-56
BCM (J/B side connector)
3
4
1
25
15 14 12
13 10
11 9 8 67
17
16182122 19
20
23
1234578 116
12 91034 652 1
G271 G273
G272
10
11 12 13 14 15 16 17 18 19123456789
20
345612L312
23414
3
561214 11
10
157 2 11316 9 8 6
5 4 3
2
1
7
11 10
9 8
15
14 13
1216
L313
L315 E325
2 1
12 34 5 6 78 9
15 16 17 18 11 10 12 13 14 1
234
5
678 910
E323
L314 E324
E323 E325E324 BCM G272G271 G273 L312 L313 L314 L315J/B
9
3
3
4
(Continued)
GND (IP) POWER GND
GND
SIGNAL
GND (FL)SIGNAL
GND (IP)
4
4
10
ST
ST RLY COIL
ST SIG
10A33
Individual circuit fuse box No.2
(In J/B)
7
6
BLOWER FAN
HTR HTR FUSEIG2 SIG
10A35
3 1
5
4
2
Connector No. / Terminal No.
56
I6RW0C910932-01

Downloaded from www.Manualslib.com manuals search engine 9B-13 Lighting Systems:
Illumination Cancel System Symptom Diagnosis (If Equipped)S6RW0D9204010
Interior Light Symptom DiagnosisS6RW0D9204011
NOTE
• Use of SUZUKI scan tool makes it easy to check whether a faulty condition is on the input side or
output side of BCM. For checking procedure, refer to “Diagnosis Using Output Test Function of
SUZUKI Scan Tool” under “Scan Tool Data in Section 10B”.
• Check each part in the order from the top of the following list.

DRL Operation Inspection (If Equipped)S6RW0D9204012
1) Confirm that lighting switch is in OFF position.
2) Confirm that dimmer and passing switch is in low beam position.
3) Check DRL for operation as follows.
a) Turn ignition switch to ON position and check headlights remain OFF.
b) Start engine and run it at idle speed. Check headlights turn ON at low beam.
c) Switch dimmer and passing switch to high beam position and check headlights remain turning ON at low
beam.
4) If check result is not as satisfied, go to “Inspection of DRL Controller and Its Circuits (If Equipped)”.
Inspection of DRL Controller and Its Circuits (If Equipped)S6RW0D9204013
1) Confirm that lighting switch is in good condition referring to “Headlight Switch (in Lighting Switch) Inspection”.
2) Confirm that oil pressure switch is in good condition referring to “Oil Pressure Switch Inspection in Section 9C”.
3) Remove glove box.
4) Remove DRL controller (1) from steering support member.
5) Connect connector to DRL controller.Condition Possible cause Correction / Reference Item
Illumination cancel do not
normal operationCircuit fuse blownReplace fuse and check for short circuit.
Illumination cancel switch faultyCheck illumination cancel switch referring to
“Illumination Cancel Switch Inspection (If
Equipped)”.
Combination meter and/or information
display faultyReplace combination meter and/or information
display.
Wiring or grounding faultyRepair circuit.
Condition Possible cause Correction / Reference Item
Dome light does not light
upBulb blownReplace bulb.
Circuit fuse blownReplace fuse and check for short circuit.
Dome light switch faultyCheck dome light switch.
Door switch faultyCheck door switch referring to “Door Switch
(Front / Rear Door) Inspection in Section 9C”.
Wiring or grounding faultyRepair circuit.
BCM faultyReplace after making sure that none of above
parts is faulty.
Luggage compartment
light does not light up (if
equipped)Bulb blownReplace bulb.
Rear end door switch faultyCheck switch referring to “Rear End Door
Switch Inspection in Section 9C”.
Wiring or grounding faultyRepair circuit.