display TOYOTA AURIS HYBRID 2012 Workshop Manual

329 3-4. Using the hands-free phone system (for cellular phone)
3
Interior features
UK_AURIS_HV_EE
Displaying the Bluetooth® device address and name
Select “Device Name” using .
Turn to display the Bluetooth
® device address and
name.
Select “Go Back” using to return to “System Setup”.
Initialization
Select “Initialize” and then “Confirm” using .
Select “Confirm” again using .
STEP1
STEP2
STEP3
STEP1
STEP2

345
3-7. Other interior features
3
Interior features
UK_AURIS_HV_EE
Clock
The clock is displayed when
The “POWER” switch is in ON mode.
When the 12-volt battery is disconnected
The time display will automatically be set to 0:00.
Press and hold the “CLOCK”
button to allow the hour indica-
tion to flash.
Press the “CLOCK” button to adjust the hours while the
hour indication is flashing.
After adjusting the hours, wait 5 seconds to allow the minute indi-
cation to flash.
Press the “CLOCK” button to adjust the minutes while the
minutes indication is flashing.
After adjusting the minutes, wait 5 seconds to return the clock
automatically to display the time.
STEP1
STEP2
STEP3

5When trouble arises
421
UK_AURIS_HV_EE
5-1. Essential information
Emergency flashers .......... 422
If your vehicle needs to
be towed ......................... 423
If you think something is
wrong .............................. 4295-2. Steps to take in an
emergency
If a warning light turns
on or a warning buzzer
sounds... ........................ 430
If a warning message is
displayed ........................ 436
If you have a flat tire
(vehicles with a spare
tire) ................................. 447
If you have a flat tire
(vehicles with an
emergency tire puncture
repair kit)......................... 459
If the hybrid system will
not start........................... 471
If you lose your keys ......... 473
If the electronic key does
not operate properly ....... 474
If the 12-volt battery is
discharged ...................... 476
If your vehicle
overheats ........................ 481
If the vehicle becomes
stuck ............................... 486
If your vehicle has to
be stopped in an
emergency ...................... 488

436
5-2. Steps to take in an emergency
UK_AURIS_HV_EE
If a warning message is displayed
Stop the vehicle immediately.
The following warnings indicate the possibility of damage to the vehi-
cle that may lead to an accident. Immediately stop the vehicle in a
safe place and contact any authorized Toyota dealer or repairer, or
another duly qualified and equipped professional.
Warning messageDetails
Indicates an abnormal engine oil pressure.
A buzzer also sounds.
The warning light may turn on if the engine oil
pressure is too low.
Indicates a malfunction in the hybrid system.
A buzzer also sounds.
If a warning is shown on the multi-information display, stay calm and
perform the following actions:
Master warning light
The master warning light also
comes on or flashes in order to
indicate that a message is cur-
rently being displayed on the
multi-information display.
Multi-information display
If any of the warning lights turns on again after performing the fol-
lowing actions, contact any authorized Toyota dealer or repairer, or
another duly qualified and equipped professional.

440 5-2. Steps to take in an emergency
UK_AURIS_HV_EE
*: For the EV-Drive Mode operating conditions (P. 180). Indicates that the EV-
Drive Mode is not
available.*
A buzzer sounds
twice.
The reason the EV-
Drive Mode is not
available (the vehicle
is idling, hybrid bat-
tery [traction battery]
charge is low, speed is
higher than the EV-
Drive Mode operating
speed range, acceler-
ator pedal is
depressed too much)
may be displayed.Use the EV-Drive Mode
when it becomes avail-
able.

(Flashes 3 times)Indicates that the EV-
Drive Mode has been
automatically can-
celled.*
A buzzer sounds
twice.
The reason the EV-
Drive Mode is not
available (the hybrid
battery [traction bat-
tery] charge is low,
speed is higher than
the EV-Drive Mode
speed range, acceler-
ator pedal is
depressed too much)
may be displayed.Drive the vehicle for a
while.
Warning messageDetailsCorrection procedure

442 5-2. Steps to take in an emergency
UK_AURIS_HV_EE
Once3 times

(Flashing)The driver’s
door has been
opened or
closed with the
shift position in
P, the “POWER”
switch in any
mode other
than off and the
electronic key
outside of the
detection area.Turn the
“POWER”
switch off or
confirm the
location of the
electronic key.
OnceContin-
uous
(Displayed alternately)

(Flashing)The electronic
key has been
taken outside
the vehicle and
the doors have
been locked
without first
turning the
“POWER”
switch to off.Turn the
“POWER”
switch to off and
lock the doors
again.
Contin-
uous

(Flashing)The driver's
door was
opened when
the shift position
was not in P
and the
“POWER”
switch was not
turned off.Push the P
position switch.
Interior
buzzerExterior
buzzerWarning messageDetailsCorrection
procedure

5
443 5-2. Steps to take in an emergency
When trouble arises
UK_AURIS_HV_EE
Contin-
uousContin-
uous
(Displayed alternately)

(Flashing)The driver’s
door was
opened and
closed while the
electronic key
was not in the
vehicle, the shift
position was not
in P and the
“POWER”
switch was not
turned off.• Push the P
position switch.
• Confirm the
location of the
electronic key.
OnceContin-
uous

(Flashing)An attempt to
lock the doors
has been made
using the smart
entry & start
system while
the electronic
key is inside the
vehicle.Take the elec-
tronic key out-
side the vehicle,
and lock the
doors again.
Once
The key battery
is low.Replace the
battery.
(P. 397)
Interior
buzzerExterior
buzzerWarning messageDetailsCorrection
procedure

5
481
5-2. Steps to take in an emergency
When trouble arises
UK_AURIS_HV_EE
If your vehicle overheats
Correction procedures
If the top segments of the engine coolant temperature gauge
are flashing
Stop the vehicle in a safe place and turn off the air condition-
ing system.
Check to see if steam is coming out from under the hood.
If you see steam:
Stop the hybrid system. Carefully lift the hood after the
steam subsides and then restart the hybrid system.
If you do not see steam:
Leave the hybrid system operating and carefully lift the
hood.
The following may indicate that your vehicle is overheating:
The top segments of the engine coolant temperature gauge are
flashing:
The engine may be overheating.
“HYBRID SYSTEM OVERHEAT” is shown on the multi-informa-
tion display:
The power control unit may be overheating.
Follow the correction procedure as described below.
STEP1
STEP2

5
483 5-2. Steps to take in an emergency
When trouble arises
UK_AURIS_HV_EEIf “HYBRID SYSTEM OVERHEAT” is shown on the multi-infor-
mation display
Stop the vehicle in a safe place and turn off the air condition-
ing system.
Leave the hybrid system operating and carefully lift the hood.
Check if the cooling fans are operating.
If the fans are operating:
Wait until “HYBRID SYSTEM OVERHEAT” disappears and then
stop the hybrid system.
If the message does not disappear, call any authorized Toyota
dealer or repair, or another duly qualified and equipped profes-
sional.
If the fans are not operating:
Stop the hybrid system immediately and call any authorized
Toyota dealer or repairer, or another duly qualified and equipped
professional.
After the hybrid system has
cooled down, check the power
control unit coolant level and
inspect the cooling system for
leaks.
STEP1
STEP2
STEP3
STEP4

497 6-1. Specifications
6
Vehicle specifications
UK_AURIS_HV_EE
The 0W portion of the oil viscosity rating indicates the characteristic of the
oil which allows cold startability. Oils with a lower value before the W allow
for easier starting of the engine in cold weather.
The 20 in 0W-20 indicates the oil viscosity when the oil is at its operating
temperature. An oil with a higher viscosity may be better suited if the vehi-
cle is operated at high speeds, or under extreme load conditions.
How to read oil container labels:
Either or both API registered marks are added to some oil containers
to help you select the oil you should use.
API Service Symbol
Top portion: The oil quality
designation by API (American
Petroleum Institute) (SM)
Center portion: The SAE viscosity
grade (SAE 0W-20)
Lower portion: “Energy-
Conserving” means that the oil
has fuel-saving capabilities.
ILSAC Certification Mark
The ILSAC (International
Lubricant Standardization and
Approval Committee) Certification
Mark is displayed on the front of
the container.