fluid TOYOTA AVALON 2001 Service Owner's Manual
[x] Cancel search | Manufacturer: TOYOTA, Model Year: 2001, Model line: AVALON, Model: TOYOTA AVALON 2001Pages: 1897, PDF Size: 26.61 MB
Page 507 of 1897
F10182
SST
F07901
2 1
(-)(+)
- BRAKEBRAKE FLUID
BR-5
1404 Author: Date:
2001 AVALON (RM808U)
(b) While an assistant depresses the pedal, loosen the
bleeder plug until fluid starts to run out. Then tighten the
bleeder plug.
(c) Repeat this procedure until there are no more air bubbles
in the fluid.
Bleeder plug tightening torque:
8.3 N´m (85 kgf´cm, 74 in.´lbf)
5. REPEAT PROCEDURE FOR EACH WHEEL
6. w/ VSC:
BLEED PRECHARGE PUMP
CAUTION:
When repairing the brake master cylinder or precharge
pump, bleed the precharge pump of the air.
(a) Install the SST to the reservoir.
SST 09992-00242, 09992-00350
(b) Using SST, apply pressure to the reservoir.
Pressure: 98.1 kpa (1.0 kgf/cm
2, 14.2 psi)
(c) Disconnect the precharge pump connector.
(d) Connect ML+ (2) terminal to the battery positive (+) and
ML- (1) terminal to the battery negative (-), and activate
the precharge pump about 20 seconds.
(e) Remove the SST from the reservoir.
(f) Connect the vinyl tube to the front brake caliper RH, and
loosen the bleeder plug.
(g) Activate the precharge pump again until there are no
more air bubbles in the fluid.
Bleeder plug tightening torque:
8.3 N´m (85 kgf´cm, 74 in.´lbf)
(h) Connect the precharge pump connector.
7. CHECK FLUID LEVEL IN RESERVOIR
Check the fluid level and add fluid if necessary.
Fluid: SAE J1703 or FMVSS No. 116 DOT3
Page 515 of 1897
BR0L7-04
- BRAKEFRONT BRAKE CALIPER
BR-33
1432 Author: Date:
2001 AVALON (RM808U)
INSTALLATION
Installation is in the reverse order of removal (See page BR-29).
HINT:
After installation, fill the brake reservoir with brake fluid, bleed brake system (See page BR-4).
Check for fluid leaks.
Page 517 of 1897
BR0L3-04
R02840
- BRAKEFRONT BRAKE CALIPER
BR-29
1428 Author: Date:
2001 AVALON (RM808U)
REMOVAL
1. REMOVE FRONT WHEEL
Remove the wheel and temporarily fasten the disc with hub
nuts.
Torque: 103 N´m (1,050 kgf´cm, 76 ft´lbf)
2. DISCONNECT FLEXIBLE HOSE
(a) Remove the union bolt and 2 gaskets from the caliper,
then disconnect the flexible hose from the caliper.
Torque: 29 N´m (300 kgf´cm, 22 ft´lbf)
HINT:
At the time of installation, install the flexible hose lock securely
in the lock hole in the caliper.
(b) Use a container to catch the brake fluid as it drains out.
3. REMOVE CALIPER
(a) Remove the 2 installation bolts.
Torque: 34 N´m (350 kgf´cm, 25 ft´lbf)
(b) Remove the caliper from the torque plate.
4. REMOVE 2 BRAKE PADS WITH ANTI- SQUEAL
SHIMS
5. REMOVE 2 PAD SUPPORT PLATES
Page 520 of 1897
R02981
- BRAKEFRONT BRAKE PAD
BR-27
1426 Author: Date:
2001 AVALON (RM808U)
10. INSTALL CALIPER
(a) Draw out a small amount of brake fluid from the reservoir.
(b) Press in the piston with a hammer handle or similar imple-
ment.
HINT:
If the piston is difficult to push in, loosen the bleeder plug and
push in the piston while letting some brake fluid escape.
(c) Install the caliper.
(d) Hold the sliding pin and torque the installation bolt.
Torque: 34 N´m (350 kgf´cm, 25 ft´lbf)
(e) Install the flexible hose and bolt to the shock absorber
bracket.
Torque: 29 N´m (300 kgf´cm, 21 ft´lbf)
11. INSTALL FRONT WHEEL
Torque: 103 N´m (1,050 kgf´cm, 76 ft´lbf)
12. DEPRESS BRAKE PEDAL SEVERAL TIMES
13. CHECK THAT FLUID LEVEL IS AT MAX LINE
Page 533 of 1897
BR15B-01
BR-58
- BRAKEPRECHARGE PUMP
1457 Author: Date:
2001 AVALON (RM808U)
INSTALLATION
Installation is in the reverse order of removal (See page BR-57).
HINT:
After installation, fill the brake reservoir with brake fluid, bleed brake system (See page BR-4).
Check for fluid leaks.
Page 538 of 1897
BR0LF-03
BR-42
- BRAKEREAR BRAKE CALIPER
1441 Author: Date:
2001 AVALON (RM808U)
INSTALLATION
Installation is in the reverse order of removal (See page BR-38).
HINT:
After installation, fill the brake reservoir with brake fluid, bleed brake system (See page BR-4).
Check for fluid leaks.
Page 540 of 1897
BR0LB-02
F09725
BR-38
- BRAKEREAR BRAKE CALIPER
1437 Author: Date:
2001 AVALON (RM808U)
REMOVAL
1. REMOVE REAR WHEEL
Remove the wheel and temporarily fasten the disc with hub
nuts.
Torque: 103 N´m (1,050 kgf´cm, 76 ft´lbf)
2. DISCONNECT FLEXIBLE HOSE
(a) Remove the union bolt and 2 gaskets from the caliper,
then disconnect the flexible hose from the caliper.
Torque: 29 N´m (300 kgf´cm, 22 ft´lbf)
HINT:
At the time of installation, insert the flexible hose lock securely
in the lock hole in the caliper.
(b) Use a container to catch the brake fluid as it drains out.
3. REMOVE CALIPER
(a) Remove the 2 installation bolts.
Torque: 34 N´m (350 kgf´cm, 25 ft´lbf)
NOTICE:
At the time of installation, insert the sliding pin with sliding
bushing into the bottom side.
(b) Remove the caliper from the torque plate.
4. REMOVE 2 BRAKE PADS WITH ANTI- SQUEAL
SHIMS
5. REMOVE 4 PAD SUPPORT PLATES
NOTICE:
There should be no oil or grease adhering to the friction
surfaces of the pads or disc.
Page 542 of 1897
BR0L9-03
F09722
F09723
R10387
- BRAKEREAR BRAKE PAD
BR-35
1434 Author: Date:
2001 AVALON (RM808U)
REPLACEMENT
1. REMOVE REAR WHEEL
2. INSPECT PAD LINING THICKNESS
Check the pad's thickness through the caliper inspection hole
and replace pads if not within specification.
Minimum thickness: 1.0 mm (0.039 in.)
3. LIFT UP CALIPER
(a) Remove the bottom side installation bolt.
(b) Lift up and suspend it securely.
HINT:
Do not disconnect the flexible hose from the caliper.
4. REMOVE 2 BRAKE PADS WITH 4 ANTI- SQUEAL
SHIMS
5. REMOVE 4 PAD SUPPORT PLATES
NOTICE:
The support plates can be used again provided that they
have sufficient rebound, no deformation, cracks or wear,
and have had all rust, dirt and foreign particles cleaned off.
6. CHECK DISC THICKNESS AND RUNOUT
(See page BR-40)
7. INSTALL PAD SUPPORT PLATES
Install the 4 pad support plates.
8. INSTALL NEW PADS
NOTICE:
When replacing worn pads, the anti-squeal shims must be
replaced together with the pads.
(a) Apply disc brake grease to both side of the inner
anti-squeal shims (See page BR-37).
(b) Install the 2 anti-squeal shims on each pad.
(c) Install 2 pads with the pad wear indicator plates facing
downward.
NOTICE:
There should be no oil or grease adhering to the friction
surfaces of the pads or the disc.
9. INSTALL CALIPER
(a) Draw out a small amount of brake fluid from the reservoir.
(b) Press in the piston with a hammer handle or similar imple-
ment.
HINT:
If the piston is difficult to push in, loosen the bleeder plug and
push in the piston while letting some brake fluid escape.
Page 543 of 1897
F09723
BR-36
- BRAKEREAR BRAKE PAD
1435 Author: Date:
2001 AVALON (RM808U)
(c) Install the caliper.
(d) Install the installation bolt.
Torque: 34 N´m (350 kgf´cm, 25 ft´lbf)
10. INSTALL REAR WHEEL
Torque: 103 N´m (1,050 kgf´cm, 76 ft´lbf)
11. DEPRESS BRAKE PEDAL SEVERAL TIMES
12. CHECK THAT FLUID LEVEL IS AT MAX LINE
Page 547 of 1897
BR0KG-05
BR-2
- BRAKETROUBLESHOOTING
1401 Author: Date:
2001 AVALON (RM808U)
TROUBLESHOOTING
PROBLEM SYMPTOMS TABLE
Use the table below to help you find the cause of the problem. The numbers indicate the priority of the likely
cause of the problem. Check each part in order. If necessary, replace these parts.
SymptomSuspect AreaSee page
Lower pedal or spongy pedal
5. Fluid leaks for brake system
6. Air in brake system
7. Piston seals (Worn or damaged)
8. Master cylinder (Faulty)
9. Booster push rod (Out of adjustment)DI-249
DI-346
BR-4
BR-28
BR-37
BR-13
BR-24
Brake drag
1. Brake pedal freeplay (Minimal)
2. Parking brake pedal travel (Out of adjustment)
3. Parking brake wire (Sticking)
4. Rear brake shoe clearance (Out of adjustment)
5. Pad (Cracked or distorted)
6. Piston (Stuck)
7. Piston (Frozen)
8. Tension or return spring (Faulty)
9. Booster push rod (Out of adjustment)
10.Vacuum leaks for booster system
11. Master cylinder (Faulty)BR-6
BR-9
-
BR-46
BR-25
BR-34
BR-28
BR-37
BR-28
BR-37
BR-43
BR-24
BR-22
BR-13
Brake pull
1. Piston (Stuck)
2. Pad (Oily)
3. Piston (Frozen)
4. Disc (Scored)
5. Pad (Cracked or distorted)BR-28
BR-37
BR-25
BR-34
BR-28
BR-37
BR-28
BR-37
BR-25
BR-34
Hard pedal but brake inefficient
1. Fluid leaks for brake system
2. Air in brake system
3. Piston (Stuck)
4. Pad (Cracked or distorted)
5. Pad (Oily)
6. Pad (Glazed)
7. Disc (Scored)
8. Booster push rod (Out of adjustment)
9. Vacuum leaks for booster systemDI-249
DI-346
BR-4
BR-28
BR-37
BR-25
BR-34
BR-25
BR-34
BR-25
BR-34
BR-28
BR-37
BR-24
BR-22