belt TOYOTA AVENSIS 1999 Supplement

RS0IQ–01
H03410
H03411
H03408
– SUPPLEMENTAL RESTRAINT SYSTEMSIDE AIRBAG ASSEMBLY
RS–19
INSTALLATION
NOTICE:
Never use airbag parts from another vehicle. When replac-
ing parts, replace them with new parts.
1. INSTALL THESE PARTS TO SEATBACK FRAME
(a) Install the seatback pad.
(b) Install the hog rings and seatback cover.
(c) Hang the hook of the seatback cover.
2. INSTALL SEATBACK TO SEAT CUSHION ASSEMBLY
Using a torx wrench, install the 4 screws and seatback assem-
bly.
Torx wrench: T40 (Part No.09042–00020 or locally
manufactured tool)
Torque: 25 N·m (255 kgf·cm, 18 ft·lbf)
3. INSTALL THESE PARTS TO FRONT SEAT ASSEMBLY
(a) Install the 2 headrest supports.
(b) Install the headrest.
(c) Install the lumber support adjusting knob.
(d) Install the front seat inner shield.
4. INSTALL FRONT SEAT
(a) Mount the seat to the vehicle.
(b) Connect the side airbag connector.
(c) Install the outer bolt and inner bolt on the front side after
sliding the seat to the rearmost position.
Torque: 37 N·m (375 kgf·cm, 27 ft·lbf)
(d) Tighten the bolts on the rear side temporarily, tighten
them completely starting from the bolt on the inner side.
Torque: 37 N·m (375 kgf·cm, 27 ft·lbf)
(e) Install the front seat belt lap outer anchor.
Torque: 42 N·m (430 kgf·cm, 31 ft·lbf)
(f) Install the front seat cushion outer shield and reclining ad-
juster knob.
(g) Install the 2 seat track covers.

RS0IR–01
H11612
Roof Headlining
Front Pillar GarnishCenter Pillar Upper Garnish
Center Pillar Lower Garnish Front Seat Outer Belt Assist Grip
Front Door Operating Trim
Front Door Scuff Plate
Rear Door Scuff Plate Rear Door Operating Trim
Map Light Sun Visor
Pillar Garnish Cover
H11611
Sedan Model Liftback Model Wagon Model
Roof Side
Inner Garnish
Side Seatback
Rear Seat CushionDeck Trim
Side Board
Rear Floor
Carpet Deck Side Trim
Cover and Panel
Tonneau
Cover
Rear Floor
Finish Plate Rear Seat
Outer Belt
Roof Side
Inner Garnish
Side Seatback
Roof Side
Inner Garnish
Rear Seatback
Assembly
Rear Side
Seatback
Room
Partition
Net
N·m (kgf·cm, ft·lbf): Specified torque
42 (430, 31)
21 (214, 15)
21 (214, 15)
21 (214, 15)
RS–20
– SUPPLEMENTAL RESTRAINT SYSTEMCURTAIN SHIELD AIRBAG ASSEMBLY
CURTAIN SHIELD AIRBAG ASSEMBLY
COMPONENTS

RS0IX–01
H03424: Specified torqueN·m (kgf·cm, ft·lbf)Side and Curtain Shield Airbag Sensor Assembly
21 (210, 15)
Front Seat Outer Belt Retractor
5.0 (51, 44 in.·lbf)
42 (430, 31)
Center Piller Garnish
Rear Door Scuff Plate
Front Door Scuff Plate
RS–34– SUPPLEMENTAL RESTRAINT SYSTEMSIDE AND CURTAIN SHIELD AIRBAG SENSOR
ASSEMBLY
SIDE AND CURTAIN SHIELD AIRBAG SENSOR ASSEMBLY
COMPONENTS

RS0IY–01
H03674
H03425
– SUPPLEMENTAL RESTRAINT SYSTEMSIDE AND CURTAIN SHIELD AIRBAG SENSOR
ASSEMBLYRS–35
REMOVAL
NOTICE:
Do not open the cover or the case of the ECU and various
electrical devices unless absolutely necessary.
(If the IC terminals are touched, the IC may be destroyed by
static electricity.)
1. REMOVE FRONT AND REAR SCUFF PLATE
2. REMOVE CENTER PILLAR LOWER GARNISH
3. REMOVE FRONT SEAT OUTER BELT RETRACTOR
(See Pub. No. RM599E on page BO–151)
(a) Disconnect the pretensioner connector.
(b) Remove the 2 bolts and retractor.
4. REMOVE SIDE AND CURTAIN SHIELD AIRBAG SEN-
SOR ASSEMBLY
(a) Disconnect the connector.
NOTICE:
Remove the connector with the sensor assembly installed.
(b) Remove the 2 bolts, nut and side and curtain shield airbag
sensor assembly.

RS0J1–01
H03425
H03674
RS–38– SUPPLEMENTAL RESTRAINT SYSTEMSIDE AND CURTAIN SHIELD AIRBAG SENSOR
ASSEMBLY
INSTALLATION
NOTICE:

Never use SRS parts from another vehicle. When re-
placing parts, replace them with new ones.

Never reuse the side and curtain shield airbag sensor
assembly involved in a collision when the airbag has
deployed.

Never repair a sensor in order to reuse it.
1. INSTALL SIDE AND CURTAIN SHILD AIRBAG SEN-
SOR
(a) Install the side and curtain shield airbag assembly with
the 2 bolts and nut.
Torque: 21 N·m (210 kgf·cm, 15 ft·lbf)
(b) Connect the side and curtain shild airbag sensor connec-
tor.
NOTICE:

Installation of the connector is done with the sensor
assembly installed. Make sure the sensor assembly
is installed with the specified torque.

If the sensor assembly has been dropped, or there are
cracks, dents or other defects in the case, bracket or
connector, replace the sensor assembly with a new
one.

When installing the sensor assembly, take care that
the SRS wiring does not interfere with other parts and
is not pinched between other parts.

After installation, shake the sensor assembly to
check that there is no looseness.
2. INSTALL FRONT SEAT OUTER BELT RETRACTOR
(See pub. No. RM599E on page BO–159)
(a) Install the retractor with the 2 bolts.
Torque:
Upper bolt: 5.0 N·m (51 kgf·cm, 44 in.·lbf)
Lower bolt: 42 N·m (430 kgf·cm, 31 ft·lbf)
(b) Connect the pretensioner connecter.
3. INSTALL CENTER PILLAR LOWER GARNISH
4. INSTALL FRONT AND REAR DOOR SCUFF PLATE

RS0J2–01
H11591
Spiral Cable Combination Meter
(Warning Light)
Front Passenger Airbag Assembly
Side Airbag Assembly (RH)
Side and Curtain Shield Airbag
Sensor Assembly (RH)
Seat Belt Pretensioner (RH) Steering Wheel Pad
(with Airbag)
Side and Curtain Shield Airbag
Sensor Assembly (LH)Seat Belt
Pretensioner (LH)
Side Airbag Assembly (LH)
Airbag Sensor Assembly Front Airbag Sensor (RH)
Front Airbag
Sensor (LH)Curtain Shield Airbag Assembly (RH) Curtain Shield Airbag Assembly (LH)
– SUPPLEMENTAL RESTRAINT SYSTEMWIRE HARNESS AND CONNECTOR
RS–39
WIRE HARNESS AND CONNECTOR
LOCATION

BO19O–02
I12752
Assist Grip Cushion
Assist Grip
Map Light
Sun Visor
Room Light
Front Pillar Garnish
Front Door
Opening TrimCenter Pillar Upper Garnish
Roof Side Inner Garnish
Front Seat Outer Belt
Rear Door Opening Trim
Rear Door Scuff Plate Side Seatback
Rear Seat Cushion
Front Door Scuff PlateCenter Pillar
Lower GarnishRoom LightSliding Roof
Opening TrimRoof
Headlining
Map LightAssist Grip Cushion
Assist Grip
42 (430, 31)
21 (214, 15)
w/ Sliding Roof:
: Specified torque
N·m (kgf·cm, ft·lbf)
21 (214, 15)
w/ Curtain shield air bag:
Front Pillar Garnish
BO–22
– BODYROOF HEADLINING (Sedan)
ROOF HEADLINING (Sedan)
COMPONENTS
w/ Curtain shield air bag:
Front Pillar Garnish

BO2J5–01
H11626
I12491
H03625
H03637
: Clip
– BODYROOF HEADLINING (Sedan)
BO–23
REMOVAL
1. REMOVE THESE PARTS:
(a) Remove the front door opening trims.
(b) w/ Curtain Shield Airbag:
(1) Using a screwdriver,raise the pillar garnish cover.
(2) Remove the bolt, pillar garnish cover and front pillar
garnish.
(3) Remove the 2 bolts.
(4) Pack the air bag with protection cover.
(c) Remove the front pillar garnishes.
(d) Remove the front door scuff plates.
(e) Remove the rear door opening trims.
(f) Remove the rear door scuff plates.
(g) Remove the center pillar lower garnishes.
(h) Remove the rear seat cushion.
2. REMOVE REAR SIDE SEATBACK
Remove the bolt and rear side seatback.
3. REMOVE CENTER PILLAR UPPER GARNISH
(a) Remove the front seat outer belt shoulder anchor.
(b) Remove the screw and center pillar upper garnish.

BO2J6–01
H11613
(2)
(3)(4)(1)
(5)
H12071
: Clip
H12072
: Clip
H03625
– BODYROOF HEADLINING (Sedan)
BO–25
INSTALLATION
1. w/ curtain shield airbag:
INSINSTALL CURTAIN SHIELD AIRBAG
In order shown in the illustration, install the deployment section
of the curtain shield airbag with the bolts and grommet.
Torque: 9.8 N·m (100 kgf·cm, 7 ft·lbf)
2. INSTALL ASSIST GRIP CUSHION
3. INSTALL ROOF HEAD LINING
Install the roof headlining with the 3 clips.
4. INSTALL THESE PARTS:
(a) w/ Sliding Roof:
Install the sliding roof opening trim.
(b) Install the map light.
(c) Install the room light.
(d) Install the sun visors and holders.
(e) Install the assist grips.
5. INSTALL ROOF SIDE INNER GARNISH
6. INSTALL CENTER PILLAR UPPER GARNISH
(a) Install the and center pillar upper garnish with the screw.
(b) Install the front seat outer belt shoulder anchor with the
bolt.
Torque: 42 N·m (430 kgf·cm, 31 ft·lbf)
7. INSTALL REAR SIDE SEATBACK
Install the rear side seatback with the bolt.
Torque: 21 N·m (214 kgf·cm, 15 ft·lbf)
8. INSTALL THESE PARTS:
(a) Install the rear seat cushion.
(b) Install the center pillar lower garnishes.
(c) Install the rear door scuff plates.
(d) Install the rear door opening trims.
(e) Install the front door scuff plates.

BO2J7–01
H11626
I12491
H03637
: Clip
H03625
BO–28
– BODYROOF HEADLINING (Liftback)
REMOVAL
1. REMOVE THESE PARTS:
(a) Remove the front door opening trims.
(b) w/ Curtain Shield Airbag:
(1) Using a screwdriver,raise the pillar garnish cover.
(2) Remove the bolt, pillar garnish cover and front pillar
garnish.
(3) Remove the 2 bolts.
(4) Pack the air bag with protection cover.
(c) Remove the front pillar garnishes.
(d) Remove the front door scuff plates.
(e) Remove the rear door opening trims.
(f) Remove the rear door scuff plates.
(g) Remove the center pillar lower garnishes.
2. REMOVE CENTER PILLAR UPPER GARNISH
(a) Remove the front seat outer belt shoulder anchor.
(b) Remove the screw and center pillar upper garnish.
3. REMOVE REAR SIDE SEATBACK
Remove the bolt and rear side seatback.