torque TOYOTA AVENSIS 1999 Supplement

BO2J4–01
H03666
H03665
H03664
H03663
– BODYINSTRUMENT PANEL
BO–19
INSTALLATION
1. INSTALL THESE PARTS:
(a) Install the reinforcement.
(b) Install the No.1 brace.
2. INSTALL INSTRUMENT PANEL
(a) Install the 6 screws and 3 nuts.
(b) Install the passenger airbag assembly with the 2 bolts.
Torque: 18 N·m (185 kgf·cm, 13 ft·lbf)
3. INSTALL HEATER CONTROL ASSEMBLY
(See Pub. No.RM599E on page AC–111)
4. INSTALL CENTER CLUSTER FINISH PANEL
Install the panel, then connect the connectors.
5. INSTALL REAR CONSOLE BOX
(a) Install the console box with the 2 bolts and 4 caps, 4
screws.
(b) M/T:
Install the shift lever knob.
6. INSTALL PARKING BRAKE HOLE COVER
7. INSTALL GLOVE COMPARTMENT DOOR
Install the glove compartment door with the 2 glove shaft.

H03662
: 3 Clips
H03661
: 3 Clips
H03660
: 3 Clips
H03659
BO–20
– BODYINSTRUMENT PANEL
8. INSTALL NO.1 UNDER COVER
Install the No.1 under cover.
9. INSTALL NO.1 REGISTER
Install the No.1 register.
10. INSTALL COMBINATION METER
11. INSTALL CLUSTER FINISH PANEL
(a) Install the cluster finish panel, then connect the connec-
tor.
(b) Install the 2 screws.
12. INSTALL THESE PARTS:
(See Pub. No. RM 599E, page SR–13)
(a) Install the steering column.
(b) Install the combination switch.
(c) Install the column cover.
13. INSTALL LOWER FINISH PANEL
(a) Install the lower finish panel with the 2 screws.
(b) Install the hood lock control lever.
14. INSTALL STEERING WHEEL
(See Pub. No. RM 599E, page SR–13)
15. INSTALL THESE PARTS:
(a) Install the front seats.
Torque: 37 N·m (375 kgf·cm, 27 ft·lbf)
(b) Install the center pillar lower covers.
(c) Install the rear door scuff plates.
(d) Install the rear door opening trims.
(e) Install the cowl side trims.
(f) Install the front door scuff plates.

I12491
– BODYINSTRUMENT PANEL
BO–21
(g) w/ Curtain Shield Airbag:
(1) Remove the protection cover.
(2) Install the 2 bolts.
Torque: 5.0 N·m (51 kgf·cm, 44 in.·lbf)
(3) Install the pillar garnish cover with the bolt.
NOTICE:
Be sure to tighten the bolt.
(4) Fell the pillar garnish cover.
(h) Install the front pillar garnishes.
(i) Install the front door opening trims.

BO19O–02
I12752
Assist Grip Cushion
Assist Grip
Map Light
Sun Visor
Room Light
Front Pillar Garnish
Front Door
Opening TrimCenter Pillar Upper Garnish
Roof Side Inner Garnish
Front Seat Outer Belt
Rear Door Opening Trim
Rear Door Scuff Plate Side Seatback
Rear Seat Cushion
Front Door Scuff PlateCenter Pillar
Lower GarnishRoom LightSliding Roof
Opening TrimRoof
Headlining
Map LightAssist Grip Cushion
Assist Grip
42 (430, 31)
21 (214, 15)
w/ Sliding Roof:
: Specified torque
N·m (kgf·cm, ft·lbf)
21 (214, 15)
w/ Curtain shield air bag:
Front Pillar Garnish
BO–22
– BODYROOF HEADLINING (Sedan)
ROOF HEADLINING (Sedan)
COMPONENTS
w/ Curtain shield air bag:
Front Pillar Garnish

BO2J6–01
H11613
(2)
(3)(4)(1)
(5)
H12071
: Clip
H12072
: Clip
H03625
– BODYROOF HEADLINING (Sedan)
BO–25
INSTALLATION
1. w/ curtain shield airbag:
INSINSTALL CURTAIN SHIELD AIRBAG
In order shown in the illustration, install the deployment section
of the curtain shield airbag with the bolts and grommet.
Torque: 9.8 N·m (100 kgf·cm, 7 ft·lbf)
2. INSTALL ASSIST GRIP CUSHION
3. INSTALL ROOF HEAD LINING
Install the roof headlining with the 3 clips.
4. INSTALL THESE PARTS:
(a) w/ Sliding Roof:
Install the sliding roof opening trim.
(b) Install the map light.
(c) Install the room light.
(d) Install the sun visors and holders.
(e) Install the assist grips.
5. INSTALL ROOF SIDE INNER GARNISH
6. INSTALL CENTER PILLAR UPPER GARNISH
(a) Install the and center pillar upper garnish with the screw.
(b) Install the front seat outer belt shoulder anchor with the
bolt.
Torque: 42 N·m (430 kgf·cm, 31 ft·lbf)
7. INSTALL REAR SIDE SEATBACK
Install the rear side seatback with the bolt.
Torque: 21 N·m (214 kgf·cm, 15 ft·lbf)
8. INSTALL THESE PARTS:
(a) Install the rear seat cushion.
(b) Install the center pillar lower garnishes.
(c) Install the rear door scuff plates.
(d) Install the rear door opening trims.
(e) Install the front door scuff plates.

I12491
BO–26
– BODYROOF HEADLINING (Sedan)
(f) w/ Curtain Shield Airbag:
(1) Remove the protection cover.
(2) Install the 2 bolts.
Torque: 5 N·m (51 kgf·cm, 44 in.·lbf)
(3) Install the front pillar garnish.
(4) Install the pillar garnish cover and bolt.
NOTICE:
Be sure to tighten the bolt.
(5) Fell the pillar garnish cover.
(g) Install the front pillar garnishes.
(h) Install the front door opening trims.

BO19R–02
I12750
Roof Headlining Assist Grip
Map LightRoof
Headlining
Sliding Roof
Opening Trim Room Light Sun Visor
Holder
Front Pillar GarnishCenter Pillar
Upper Garnish
Rear Door
Opening Trim
Front Door Scuff Plate
Front Door
Scuff PlateCenter Pillar
Lower GarnishRear Door
Scuff Plate w/ Sliding Roof:
: Specified torqueN·m (kgf·cm, ft·lbf)
42 (430, 31)
Assist Grip
Rear Side Seatback
21 (214, 15)
Front Pillar Garnish
42 (430, 31)
Roof Side Inner Garnish
21 (214, 15)
w/ Curtain shield air bag:
Front Pillar Garnish
– BODYROOF HEADLINING (Liftback)
BO–27
ROOF HEADLINING (Liftback)
COMPONENTS

BO2J8–01
H11613
(2)
(3)(4)(1)
(5)
H03647
: Clip
H12072
: Clip
H03625
BO–30
– BODYROOF HEADLINING (Liftback)
INSTALLATION
1. w/ Curtain Shield Airbag:
INSTALL CURTAIN SHIELD AIRBAG
In order shown in the illustration, install the deployment section
of the curtain shield airbag with the bolts and grommet.
Torque: 9.8 N·m (100 kgf·cm, 7 ft·lbf)
2. INSTALL ASSIST GRIP CUSHION
3. INSTALL ROOF HEAD LINING
Install the 3 clips and roof headlining.
4. INSTALL THESE PARTS:
(a) w/ Sliding Roof:
Install the sliding roof opening trim.
(b) Install the map light.
(c) Install the room light.
(d) Install the sun visors and holders.
(e) Install the assist grips.
5. INSTALL ROOF SIDE INNER GARNISH
6. INSTALL CENTER PILLAR UPPER GARNISH
(a) Install the center pillar upper garnish with the screw.
(b) Install the front seat outer belt shoulder anchor with the
bolts.
Torque: 42 N·m (430 kgf·cm, 31 ft·lbf)
7. INSTALL REAR SIDE SEATBACK
Install the rear side seatback with the bolt.
Torque: 21 N·m (214 kgf·cm, 15 ft·lbf)
8. INSTALL THESE PARTS:
(a) Install the center pillar lower garnishes.
Torque: 21 N·m (214 kgf·cm, 15 ft·lbf)
(b) Install the rear door scuff plates.
(c) Install the rear door opening trims.
(d) Install the front door scuff plates.

I12491
– BODYROOF HEADLINING (Liftback)
BO–31
(e) w/ Curtain Shield Airbag:
(1) Remove the protection cover.
(2) Install the 2 bolts.
Torque: 5 N·m (51 kgf·cm, 44 in.·lbf)
(3) Install the front pillar garnish.
(4) Install the pillar garnish cover and bolt.
NOTICE:
Be sure to tighten the bolt.
(5) Fell the pillar garnish cover.
(f) Install the front pillar garnishes.
(g) Install the front door opening trims.

BO19U–02
I12753
Roof Headlining Rear Room Partition
Net Hook
Assist Grip
Map Light
No.2 Room LightAssist GripRoof
Headlining
Sliding Roof Opening Trim Room Light Sun Visor
Holder
Front Pillar GarnishCenter Pillar
Upper GarnishRear Door
Opening Trim
Roof Side Inner Garnish
Deck Side Trim Cover
and Panel
Deck Trim Side Board
Rear Seat Outer Belt
Tonneau Cover
Rear Floor Finish Plate
Roof Side
Inner Garnish
Deck Side Trim Cover
and Panel
Deck Trim Side Board Rear Seatback
AssemblyRear Floor CarpetRoom Partition Net
Rear Side SeatbackFront Door Scuff Plate
Front Pillar Garnish
Front Door
Scuff PlateCenter Pillar
Lower GarnishRear Door
Scuff Plate w/ Sliding Roof:
: Specified torqueN·m (kgf·cm, ft·lbf)
42 (430, 31)
37 (378, 27)
42 (430, 31)
21 (214, 15)
21 (214, 15)
w/ Curtain shield air bag:
Front Pillar Garnish
BO–32
– BODYROOF HEADLINING (Wagon)
ROOF HEADLINING (Wagon)
COMPONENTS