TOYOTA AVENSIS 2002 Repair Manual

750NA±01
H19020
± ENGINE HOOD/DOORBACK DOOR STAY
75±47
AVENSIS REPAIR MANUAL (RM1018E)
BACK DOOR STAY
REPLACEMENT
HINT:
Use the same procedures on the RH side as on the LH side.
1. REMOVE BACK DOOR STAY ASSY LH
(a) Using a screwdriver, remove the stay from the door panel.
HINT:

Remove the door stay while supporting the back door with
your hands.

Tape the screwdriver tip before use.
(b) Remove the 2 bolts and stay from the body.
2. INSTALL BACK DOOR STAY ASSY LH
(a) Install the stay with the bolts.
Torque:
22 N
m (264 kgf
cm, 19 ft
lbf) on door side
7.0 N
m (71 kgf
cm, 63 in.
lbf) on body side

750NB±01
B65104
AB ab 75±48
± ENGINE HOOD/DOORBACK DOOR STAY
AVENSIS REPAIR MANUAL (RM1018E)
DISPOSAL
HINT:
Use the same procedures on the RH side as on the LH side.
1. DISPOSE OF BACK DOOR STAY ASSY LH
(a) Horizontally fix the stay in a vise with the piston±rod pulled
out.
(b) Wearing safety glasses, gradually cut a part between A
and B as shown in the illustration using a metal saw to
gradually release the gas.
Standard dimension:
a80 mm (3.15 in.)
b20 mm (0.80 in.)
NOTICE:
Although the gas inside the stay is colorless, odorless and
harmless, there is a possibility that metal debris from cut-
ting could be blown out. Therefore, cover it with clothes or
thr like.

750MV±01
B67988
Front Door Glass
Sub±assy LH Front Door Glass Run LH
Front Door Frame Sub±assy Rear Lower LH
8.0 (82, 71 in.´lbf)
Front Door Glass Weatherstrip Inner LH
Front Door Trim Board Sub±assy LH Front Door Armrest
Base Panel Upper
Courtesy Lamp
: Specified torque
N´m (kgf´cm, ft´lbf)Front No. 1 Speaker Assy Front Door Inside Handle Sub±assy LH
Fuel Lid Opener Switch
Front Door Trim Base LHClip
Power Window Regulator
Switch Assy Front Door Armrest Base Panel Upper
w/o Rear Power Window
Front Door Window Regulator
Sub±assy LH
8.0 (82, 71 in.´lbf)
Power Window Regulator
Master Switch Assy
Rivet
Non±reusable part


5.5 (56, 49 in.´lbf)
75±4
± ENGINE HOOD/DOORFRONT DOOR
AVENSIS REPAIR MANUAL (RM1018E)
FRONT DOOR
COMPONENTS

B67989
Front Door Outside Handle Frame Sub±assy LHw/ Key:
Front Door Outside Handle Cover LH
Front Door Handle
Assy Outside LH
Front Door Outside Handle Pad Rear Front Door Outside
Handle Pad Front
Hole Plug
Front Door Lock Open Rod
Front Door w/ Motor Lock Assy LH
Door Lock Wire Harness Packing 5.0 (51, 44 in.´lbf)
Front Door Belt Moulding LH
Front Door Hinge
Assy Upper LH
Front Door Check Assy
30 (306, 22)

5.5 (56, 49 in.´lbf)
Front Door Hinge
Assy Lower LH26 (265, 19)
Front Door Weatherstrip LH
Cushion RubberFront Door Lower Frame
Bracket Garnish LH Outer Rear View Mirror Assy LH
Front Door Speaker No. 2
Front Door Service Hole Cover 
: Specified torqueN´m (kgf´cm, ft´lbf)


Precoated Part Non±reusable part Clip
26 (265, 19)
Front Door Lower
Frame Seal


Butyl Tape

10 (102, 7)
Front Door Stiffener
Cushion No. 1
Side Trim
Spacer LH
Key Cylinder
w/o Key:
Front Door Outside
Handle Cover LHw/ Speaker
Front Door Lower Frame
Bracket Garnish LH
± ENGINE HOOD/DOORFRONT DOOR
75±5
AVENSIS REPAIR MANUAL (RM1018E)

750MW±01
B57104
Centering BoltStandard Bolt
B66965
A
B
C
ED
B66966
75±6
± ENGINE HOOD/DOORFRONT DOOR
AVENSIS REPAIR MANUAL (RM1018E)
ADJUSTMENT
HINT:

Use the same procedures on the RH side as on the LH side.

Because a centering bolt is used as a door hinge mount-
ing bolt on the body side and the door side, the door can
not be adjusted with them on. Substitute a bolt with a
washer for the centering bolt.
1. INSPECT FRONT DOOR PANEL SUB±ASSY LH
(a) Check that the clearance is within the standard range.
Standard range:
A4.6
1.5 mm (0.181
0.059 in.)
B5.5
1.5 mm (0.220
0.059 in.)
C4.6
1.5 mm (0.181
0.059 in.)
D160 mm (6.30 in.)
E4.8
1.5 mm (0.189
0.059 in.)
2. ADJUST FRONT DOOR PANEL SUB±ASSY LH
(a) Using SST, adjust the door horizontally and vertically by
loosening the body side hinge bolts.
SST 09812±00010, 09812±00020
(b) Tighten the body side hinge bolts after the adjustment.
SST 09812±00010, 09812±00020
Torque: 26 N
m (265 kgf
cm, 19 ft
lbf)

B66967
B62411
± ENGINE HOOD/DOORFRONT DOOR
75±7
AVENSIS REPAIR MANUAL (RM1018E)
(c) Adjust the door forward/rearward and vertically by loos-
ening the door side hinge bolts.
(d) Tighten the door side hinge bolts after the adjustment.
Torque: 26 N
m (265 kgf
cm, 19 ft
lbf)
(e) Adjust the striker position by slightly loosening the striker
mounting screws and hitting the striker with a plastic±
faced hammer.
(f) Tighten the striker mounting screws after the adjustment.
Torque: 23 N
m (235 kgf
cm, 17 ft
lbf)

750MX±01
B66969: Clip
B66970
: Clip
: Claw
B67801
Claw
75±8
±
ENGINE HOOD/DOOR FRONT DOOR
AVENSIS REPAIR MANUAL (RM1018E)
OVERHAUL
HINT:

The installation is in the reverse order of the removal. However, when there is a special point concern-
ing the installation, it is indicated.

Use the same procedures on the RH side as on the LH side. 1.REMOVE FRONT DOOR LOWER FRAME BRACKETGARNISH LH
(a)Using a screwdriver, disengage the 2 clip and remove the garnish.
HINT:
Tape the screwdriver tip before use.
(b)w/ Speaker: Remove the front door speaker No. 2 (See page
67±12).
2. REMOVE FRONT DOOR TRIM BASE LH
(a) Using a screwdriver, disengage the 5 claws and clip, and remove the trim base.
HINT:
Tape the screwdriver tip before use.
3. REMOVE FUEL LID OPENER SWITCH
(a) Using a screwdriver, disengage the 2 claws and remove the switch.
HINT:
Tape the screwdriver tip before use.

B70388
B66971: Clip
Protective
TapeProtective
Tape
Screw
BoltCushion Rubber
B70121
B68930
Claw A
: Claw 1
2
± ENGINE HOOD/DOORFRONT DOOR
75±9
AVENSIS REPAIR MANUAL (RM1018E)
4. REMOVE POWER WINDOW REGULATOR MASTER
SWITCH ASSY
(a) Using a screwdriver, disengage the 4 claws and clip, and
remove the armrest base panel upper together with the
switch.
HINT:
Tape the screwdriver tip before use.
(b) Disconnect the switch connector.
(c) Remove the 3 screws and switch from the armrest base
panel upper.
5. REMOVE FRONT DOOR TRIM BOARD SUB±ASSY LH
(a) Disconnect the courtesy lamp connector.
(b) Remove the 3 cushion rubbers.
(c) Remove the 2 screws and bolt as indicated.
(d) Using a clip remover, disengage 9 clips.
(e) Remove the trim board upward.
HINT:
In order to prevent the door panel from being damaged, cover
the areas indicated by the arrow marks in the illustration with
protective tape.
(f) Disengage the 2 claws and remove the courtesy lamp.
6. REMOVE FRONT DOOR GLASS WEATHERSTRIP
INNER LH
(a) Remove the weatherstrip inner upward in the direction in-
dicated by the arrow mark in the illustration.
7. REMOVE FRONT DOOR INSIDE HANDLE SUB±ASSY
LH
(a) Using a screwdriver, disengage the claw A indicated.
HINT:
Tape the screwdriver tip before use.
(b) Move the inside handle in the direction indicated the by
arrow mark in the illustration.
(c) Disconnect the 2 cables from the inside handle.

B69067
Butyl Tape
B66981
B68929
B61431
75±10
±
ENGINE HOOD/DOOR FRONT DOOR
AVENSIS REPAIR MANUAL (RM1018E)
8.REMOVE FRONT DOOR SERVICE HOLE COVER
(a)Remove the service hole cover.
NOTICE:
Remove the tape remaining on the door side.
(b)Remove the lower frame seal.
9.REMOVE OUTER REAR VIEW MIRROR ASSY LH
(a)Disconnect the mirror connector.
(b)Remove the 3 screws and mirror.
NOTICE:
When the screws are removed, the mirror may fall and be-
come deformed.
10.REMOVE FRONT NO.1 SPEAKER ASSY (W/ SPEAKER)
(a)Using a drill of less than ù 4 mm (0.16 in.), drill out the 3 rivets heads and remove the speaker.
NOTICE:

Prizing the hole with a drill can lead to damage to the
rivet hole or breaking the drill.

Be careful with the cut rivet, because it is hot.
(b)Even if the flange is taken off, continue drilling and push out the remaining fragments using the drill.
(c)Using a vacuum cleaner, remove the drilled rivet and dust from the inside of the door.
11.REMOVE FRONT DOOR BELT MOULDING ASSY LH (See page 76±23)
12. REMOVE FRONT DOOR STIFFENER CUSHION NO.1
(a) Using a screwdriver, disengage the 2 claws and remove the cushion.
13. REMOVE FRONT DOOR SPACER LH
(a) Using a screwdriver, disengage the 2 claws and remove the spacer.

B62422
B62423
12
B66968
B61434

B68932Hole Plug
± ENGINE HOOD/DOORFRONT DOOR
75±11
AVENSIS REPAIR MANUAL (RM1018E)
14. REMOVE FRONT DOOR GLASS SUB±ASSY LH
HINT:
Insert a shop rag inside the door panel to prevent the glass from
being scratched.
(a) Move the door glass until the bolts appear in the service
holes.
(b) Remove the 2 bolts holding the door glass to the window
regulator.
(c) Remove the door glass in the direction indicated by the
arrows in the illustration.
NOTICE:

Do not damage the glass.

When the bolts are removed, the glass may fall and
become deformed.
(d) Remove the glass run.
15. REMOVE FRONT DOOR WINDOW REGULATOR
SUB±ASSY LH
(a) Disconnect the window regulator connector.
(b) Remove the 6 bolts and window regulator.
NOTICE:
When the bolts are removed, the window regulator may fall
and become deformed.
HINT:
Remove the window regulator through the service hole.
16. REMOVE FRONT DOOR FRAME SUB±ASSY REAR
LOWER LH
(a) Remove the bolt and frame.
HINT:
Remove the frame through the service hole.
17. REMOVE FRONT DOOR OUTSIDE HANDLE COVER
(a) Remove the hole plug.
(b) Using a torx socket wrench (T30), loosen the screw and
remove the cover with the door lock key cylinder installed.