headlamp TOYOTA AVENSIS 2003 Service Owner's Manual

E68132
E68133
E65594
Free Pushed in4
2
1 3
±
LIGHTING LIGHTING SYSTEM
65±13
AVENSIS REPAIR MANUAL (RM1018E)
20. HEADLAMP LEVELING SWITCH
(a) Connect the battery positive (+) lead to the terminal 1 and
the battery negative (±) lead to the terminal 5.
(b) Measure the resistance between the terminal 2 and the battery negative (±) lead when headlamp leveling switch
is operated.
(c) Measure the resistance between the terminal 4 and the
battery negative (±) lead when headlamp leveling switch
is operated.
Standard:
Switch positionResistance (
)
01.0 ± 1.2
11.6 ± 1.9
22.3 ± 2.6
32.9 ± 3.3
43.5 ± 3.9
54.1 ± 4.6
(d) Inspect switch illumination.
(1) Connect the battery positive (+) lead to the terminal3 and the battery negative (±) lead to the terminal
5, and check that the illumination comes on.
21. STOP LAMP SWITCH ASSY (W/O CRUISE CONTROL)
(a) Check the continuity between each of the terminals when switch is operat\
ed. Standard:
ON (When shaft is pushed): No continuity
OFF (When shaft is not pushed): Continuity 22. STOP LAMP SWITCH ASSY (W/ CRUISE CONTROL)
(a) Check the continuity between the terminals at eachswitch position as shown in the chart.
Standard:
Switch positionTester connectionSpecified condition
Switch pin free1 ± 2No continuity
Switch pin free3 ± 4Continuity
Switch pin pushed in1 ± 2Continuity
Switch pin pushed in3 ± 4No continuity
23. BACK UP LAMP SWITCH ASSY
(a) Check the continuity between each of the terminals when switch is operat\
ed. Standard:
ON (When shaft is pushed): Continuity
OFF (When shaft is not pushed): No continuity
http://vnx.su

660CS±01
E68351
I35261


E68352
±
WIPER & WASHERHEADLAMP WASHER ACTUATOR SUB±ASSY LH
66±25
AVENSIS REPAIR MANUAL (RM1018E)
HEADLAMP WASHER ACTUATOR SUB±ASSY LH
REPLACEMENT
1.REMOVE FRONT BUMPER COVER (See page 76±3)
2. R E M O V E H E A D L A M P WA S H E R A C T U ATO RSUB±ASSY LH
(a) Separate the headlamp cleaner hose from the headlamp washer actuator sub±assy.
(b) Pull out the headlamp cleaner washer nozzle.
(c) Disengage the 2 claws, remove the headlamp cleaner washer nozzle.
(d) Remove the 2 bolts.
(e) Deform the upper part of the headlamp washer actuator sub±assy LH, to remove it.
http://vnx.su

±
WIPER & WASHER WIPER AND WASHER SYSTEM
66±3
AVENSIS REPAIR MANUAL (RM1018E)
3. REAR WIPER AND WASHER SYSTEM
SymptomSuspect AreaSee page
Rear wiper and washers do not operate.
1. AMI fuse
2. RR WIP fuse
3. Windshield wiper switch assy
4. Wire harness or connector±
±
66±6 ±
Rear wiper does not operate in INT.
1. Windshield wiper switch assy
2. Rear wiper motor assy
3. Wire harness or connector66±6
66±6±
Rear washer motor does not operate.
1. Windshield washer switch assy
2. Rear washer motor assy
3. Wire harness or connector66±6
66±6±
Rear wiper does not operate when washer switch is in ON.
1. Windshield wiper switch assy
2. Rear wiper motor assy
3. Wire harness or connector66±6
66±6±
Rear washer fluid does not operate.Washer hose and nozzle±

When rear wiper switch is in ON position, the wiper blade is in
contact with the body.

When the wiper switch is OFF, the wiper blade does not retract
or the retract position is wrong.
1. Rear wiper motor assy
2. Rear wiper blade installation position66±6
66±17
4. HEADLAMP CLEANER SYSTEM
SymptomSuspect AreaSee page
Headlamp cleaner system does not operate.
1. H/CLN fuse
2. Headlamp cleaner switch assy
3. Windshield wiper switch assy (w/ HID)
4. Headlamp cleaner control relay
5. Intergeneration Relay
6. Wire harness or connector±
66±6
66±6
66±6 ±
±
http://vnx.su

660CL±01
E67356
E67356
E67352
E68115
66±4
±
WIPER & WASHER WIPER AND WASHER SYSTEM
AVENSIS REPAIR MANUAL (RM1018E)
ON±VEHICLE INSPECTION
1. WINDSHIELD WASHER MOTOR AND PUMP ASSY
(a) Operation Check (1) Pour the washer fluid into the washer jar with thewasher motor and the pump installed to the washer
jar assy.
(2) Connect the battery (+) to the terminal 1 of the wind- shield washer motor and pump assy, the battery (±)
to the terminal 2 of the windshield washer motor and
pump assy. Check that the washer fluid comes out
from the washer jar.
2. REAR WASHER MOTOR ASSY
(a) Operation Check
(1) Pour the washer fluid into the washer jar with thewasher motor and the pump installed to the washer
jar assy.
(2) Connect the battery (+) to the terminal 1 of the rear washer motor assy, the battery (±) to the terminal 2
of the rear washer motor assy. Check that the wash-
er fluid comes out from the washer jar.
3. HEADLAMP CLEANER MOTOR AND PUMP ASSY
(a) Operation Check (1) Pour the washer fluid into the washer jar with thewasher motor and the pump installed to the washer
jar assy.
(2) Connect the battery (+) to the terminal 2 of the head- lamp cleaner motor and pump assy, the battery (±)
to the terminal 1 of the headlamp cleaner motor and
pump assy. Check that the washer fluid comes out
from the washer jar.
4. RAIN SENSOR
(a) Check voltage of each terminal of the connector
Standard:
Tester connectionConditionSpecified voltage
2 ± 3Rain sensor is covered by
handSignal waveform
http://vnx.su

E68141
E67355
Wagon Type:Automatic Stop Position
Automatic Stop Position
Lift Back Type: 170


3

160

3

E68111
66±10
±
WIPER & WASHER WIPER AND WASHER SYSTEM
AVENSIS REPAIR MANUAL (RM1018E)
5. REAR WIPER MOTOR ASSY
(a) Connect the battery (+) to the terminal 1 (+B) of the con- nector, the battery (±) to the terminal 3 (LS) of the connec-
tor and rear wiper motor assy body, and check that the
rear wiper motor assy operate.
(b) Automatic Stop Position Operation Check (1) Connect the battery (+) to the terminal 1 (+B) of the
connector, the battery (±) to the terminal 3 (LS) of
the connector and rear wiper motor assy body. With
the motor being rotated disconnect the terminal 3
(LS) from the battery (±), then check that the wiper
motor stops automatically at the automatic stop
position.
6. HEADLAMP CLEANER SWITCH ASSY
(a) Check that there is continuity between terminal at each switch position as shown in the chart.
Switch operationTester connectionSpecified condition
OFF1 (E) ± 4 (R)No continuity
ON1 (E) ± 4 (R)Continuity
Illumination circuit2 (ILL) ± 3 (ILL+)Continuity
(b) Inspect illumination operation.(1) Connect the positive (+) lead from the battery to theterminal 3 and negative (±) lead to the terminal 2,
then check that the illumination comes on.
http://vnx.su

E68112


E69072
±
WIPER & WASHER WIPER AND WASHER SYSTEM
66±11
AVENSIS REPAIR MANUAL (RM1018E)
7. HEADLAMP CLEANER CONTROL RELAY
(a) w/o HID:
Inspect headlamp cleaner control relay operation
(1) Check that no continuity exists between the termi-
nals 2 and the terminal 3.
(2) Connect the positive (+) lead from the battery to the terminal 1 and the terminal 5, and the negative (±)
lead from the battery to the terminal 3.
(3) Connect the negative (±) lead from the battery to the terminal 4, and check that continuity exists between
the terminal 2 and the terminal 5 for 0.8 to 0.9 se-
conds, then no continuity exists.
(b) w/ HID: Inspect headlamp cleaner control relay operation
(1) Check that no continuity exists between the termi-
nal 2 and the terminal 5.
(2) Connect the positive (+) lead from the battery to the terminal 1, and the negative (±) lead from the bat-
tery to the terminal 5.
(3) Connect the negative (±) lead from the battery to the terminal 4, and check that continuity exists between
the terminal 2 and the terminal 5 for 0.7 to 0.9 se-
conds, then no continuity exists.
(4) Disconnect the positive (+) lead from the battery from the terminal 1, and connect the positive (+)
lead from the battery to the terminal 1 again.
http://vnx.su

6804U±01
I35269
Engine Room No.2 Relay Block
Engine Room Relay Block
Glow Plug Relay AssyEngine Room No.3 Relay Block
Engine Room No.2 Relay Relay
Engine Room No.3 Relay Block
ENGINE:
3ZZ±FE:
1ZZ±FE:
2AZ±FSE:
1AZ±FSE:
1AZ±FE:
ENGINE:
1CD±FTV:
w/o Discharge headlamp:
Headlamp Cleaner Control Relay
w/ Discharge headlamp:
Headlamp Cleaner Control Relay Assy
w/o Discharge headlamp:
Headlamp Cleaner Control Relay
w/ Discharge headlamp:
Headlamp Cleaner Control Relay Assy
Engine Room Relay Block
±
WIRING POWER SOURCE
68±1
AVENSIS REPAIR MANUAL (RM1018E)
POWER SOURCE
LOCATION
http://vnx.su

B68229
w/ Headlamp CleanerHeadlamp Washer
Actuator Sub±assy RH
Headlamp Washer
Actuator Sub±assy LH
Radiator Grille Lower
Front Bumper Cover
Headlamp Washer
Nozzle Sub±assy LH
Headlamp Washer
Nozzle Sub±assy RH
Front Spoiler
Cover LH
Front Spoiler
Cover RH
76±2
±
EXTERIOR/INTERIOR TRIM FRONT BUMPER
AVENSIS REPAIR MANUAL (RM1018E)
http://vnx.su

760WY±01
B67425
Claw
B67431
±
EXTERIOR/INTERIOR TRIM FRONT BUMPER
76±3
AVENSIS REPAIR MANUAL (RM1018E)
REPLACEMENT
HINT:
The installation is in the reverse order of the removal. However, when there is a special point concerning
the installation, it is indicated.
1. REMOVE FRONT BUMPER COVER
(a) Put protective tape under the front fender.
HINT:
Because the spoiler covers LH and RH are assembled, remove
them together.
(b) Remove the spoiler.(1) Remove the 9 screws and 6 claws.
(2) Remove the 6 retainers.
(3) Remove the spoiler covers LH and RH together.
(4) Remove the bolt and separate the spoiler cover RHfrom the LH.
(c) Remove the 3 bolts and 2 clips.
(d) Using a screwdriver, disengage the 6 claws and remove the bumper cover.
HINT:
Tape the screwdriver tip before use.
(e) w/ Fog lamp:
Disconnect the fog lamp connectors.
2. R E M O V E H E A D L A M P WA S H E R A C T U ATO R SUB±ASSY LH (W/ HEADLAMP CLEANER)
(a) Remove the washer hose clip.
(b) Using a screwdriver, pry out the front washer nozzle.
HINT:
Tape the screwdriver tip before use.
(c) Remove the 2 screws and actuator.
3. REMOVE HEADLAMP WASHER ACTUATOR SUB±ASSY RH (W/ HEADLAMP CLEANER)
HINT:
Use the same procedures described for the LH side.
4. REMOVE INTERCOOLER COOLING AIR DUCT SUB±ASSY (W/ CAC 1CD±FTV ENGI\
NE TYPE)
(a) Remove the 3 screws and air duct.
5. REMOVE FRONT BUMPER REINFORCEMENT SUB±ASSY
(a) Using a screwdriver, remove the wire harness.
(b) Remove the 8 bolts and reinforcement.
6. REMOVE FRONT BUMPER SIDE RETAINER LH
(a) Using a screwdriver, remove the 2 screws and retainer.
HINT:
Tape the screwdriver tip before use.
http://vnx.su