TOYOTA AYGO 2011 Owners Manual

ENGINE (IGNITION) SWITCH, TRANSMISSION AND PARKING BRAKE151
NOTICE
zThe system will not allow shifting
to the “R” position if the vehicle
speed is over 6 km/h (3 mph). In
case the shift lever is operated un-
der this condition, the “N” indicator
in the instrument cluster will blink.
However, when the vehicle speed
drops below 6 km/h (3 mph), the
gear is shifted to reverse. Make
sure that the vehicle has stopped
completely before shifting to the
“R” position.
zOn an uphill, never hold the vehicle
stop only by the accelerator pedal
operation or when the starting as-
sist system is being activated.
Otherwise the warning buzzer
(pulse sound) will sound and the
clutch may be damaged. In such a
case, pull over and shift the shift
lever to the “N” position. Wait for
around 15 minutes to cool the
clutch before starting again.
zIf the gear cannot be engaged to
reverse when the shift lever is
shifted from the “N” to “R” posi-
tion, try to shift the shift lever to
the “N” position once, then shift it
to “R” position a few seconds later.
(e) Stopping
The vehicle can be stopped by depressing
the brake pedal regardless of the gear
position. This is because the clutch is
automatically disengaged to prevent the
engine from stopping. If the shift lever is
in the “M” position, the gear will be down-
shifted to 1st when the vehicle stops.
However, if you do not drive the vehicle
over 40 km/h (24 mph) or convert the
drive position after starting with the gear
in 2nd, the gear will not be downshifted
to 1st when the vehicle stops the next
time and the gear is left in 2nd.
In case the driver ’s door is opened with
the gear in “M”, “E” or “R” position and
without depressing the brake pedal, a
warning buzzer (long pulse sound) will
sound.
When the engine switch is “ON” and the
vehicle speed is slower than 9 km/h (5
mph), the shift lever will be locked if the
shift lever is in “N” position and the brake
pedal is released for approximately 2 sec-
onds.
Shift lock system is designed for prevent-
ing the vehicle from starting off by the
unintended activation of the starting assist
system.
The shift lock can be released by de-
pressing the brake pedal without holding
the shift lever.
11 02.18
AYGO WE 99E37E

152ENGINE (IGNITION) SWITCH, TRANSMISSION AND PARKING BRAKE
CAUTION
DWhen stopping, for example, at a
traffic light, be sure to depress the
brake pedal firmly. For your safety,
apply parking brake, too, when
stopping on a hill.
DWhen racing the engine, make sure
that the gear position is in the “N”
position by the gear position indica-
tor. In case the accelerator is oper-
ated with the gear in any other
position, the vehicle may move re-
sulting in an unexpected accident.
DDo not leave your vehicle unat-
tended while the engine is running.
DWhen leaving the vehicle, stop the
engine and park the vehicle with
the gear engaged. In case you need
to leave the vehicle with the engine
running, apply the parking brakes
firmly, and shift the shift lever in
the “N” position. When the driver ’s
door is opened with the shift lever
in the “M” position while stopping
with the engine running, warning
buzzer (long pulse sound) will
sound. If this happens on a hill
when starting off the vehicle, the
vehicle may move unexpectedly and
cause an accident.
NOTICE
zOn an uphill, never hold the vehicle
stop only by the accelerator pedal
operation or when the starting as-
sist system is being activated.
Otherwise the warning buzzer
(pulse sound) will sound and the
clutch may be damaged. In such a
case, pull over and shift the shift
lever to the “N” position. Wait for
around 15 minutes to cool the
clutch before starting again.
zIf the shift lever is operated more
than necessary, the system may not
allow operation of the shift lever
for a certain period of time, and the
gear may not be shifted appropri-
ately. Therefore, do not operate the
shift lever if not necessary.
(f) Parking
Unlike the automatic transmission, the
multi−mode manual transmission does not
have a parking position. The vehicle can
be parked with the shift lever in any posi-
tion.
1. Apply the parking brake firmly.
2. While depressing the brake pedal, shift
the shift lever in the “R” position on a
downhill or a level surface, and the
“M(1)” position on an uphill by confirm-
ing the gear position with the gear
position indicator.
3. Stop the engine.
11 02.18
AYGO WE 99E37E

ENGINE (IGNITION) SWITCH, TRANSMISSION AND PARKING BRAKE153
MS16008
1: Uphill
2: Level or downhill
To stop the engine:
Check the transmission gear position by
the gear position indicator, then turn the
engine switch off to stop the engine. Re-
lease the brake pedal after a few sec-
onds. The shift lever will be locked in the
position just before the engine switch was
turned off.
You can check the gear position by the
gear position indicator within 5 seconds
after turning the engine switch off.
CAUTION
DIf the gear is not engaged properly
and completely before the engine
switch is turned off, the vehicle
may not be parked with the gear
engaged. Always confirm the gear
position with the gear position indi-
cator when parking.
DOn a level surface or a downhill,
the gear should be put in reverse,
and in the “M(1)” or “E(1)” on an
uphill. Otherwise, the vehicle may
move, and cause an unexpected ac-
cident. If the gear is left in the “N”
position, the vehicle can not be
parked with the gear engaged.
(g) Cancel from parking with gear
Depress the brake pedal, and turn the en-
gine switch to the “ON” position. The shift
lever lock will be released.
Then, shift the shift lever to the “N” posi-
tion. The gear will be disengaged.
11 02.18
AYGO WE 99E37E

154ENGINE (IGNITION) SWITCH, TRANSMISSION AND PARKING BRAKE
A warning buzzer will sound or the indica-
tor will blink under the following condi-
tions:
Warning buzzer (long pulse sound)
DThe buzzer will sound if the starting
assist system is being activated for a
long period of time.
DThe engine switch is turned to the
“OFF” position with the gear in 2nd or
either 3rd, 4th or 5th.
In this case, turn the engine switch to the
“ON” position and shift the shift lever in
the “N” position, then shift it to the “E” or
“M” or “R” position, then turn the engine
switch to “OFF”.
DDuring a stop, the driver ’s door is
opened with the shift lever in the “R”,
“E” or “M” position while the engine is
running.
Warning buzzer (continuously sound)
During a stop, the driver ’s door is opened
with the shift lever in the “R”, “E” or “M”
position while the engine is running.
Warning buzzer (pulse sound)
The clutch is heated with excessive load.
NOTICE
In these cases, pull over and shift the
shift lever to the “N” position. Wait
for around 15 minutes to cool down
the clutch before starting again.
Otherwise the clutch may be dam-
aged.
Warning buzzer (short pulse sound)
DThe transmission is shifted down to a
gear where the engine is over−revving.
DThe buzzer will sound once when the
shift lever is shifted to the “R” position.
MS16011
“N” indicator blinking
When the gear indicator lamp blinks “N”,
perform any one of the following opera-
tions:
DShift the shift lever to the “N” position
once, and wait for a few seconds, shift
the shift lever again to the “E”, “M” or
“R” position.
DShift the shift lever to the “N” position
once and confirm that the engine has
started. Then, shift the shift lever to
the “E”, “M” or “R” position.
DTurn the engine switch “ON” before op-
erate the shift lever. Shift the shift le-
ver to the “N” position once, then shift
the shift lever again to the “E”, “M” or
“R” position.
“N” indicator blinking and warning
buzzer (long pulse sound) beeping.
If this condition would remain for a long
period of time, make sure the engine
switch is being “ON” and then shift the
shift lever to “N”. After the operation, shift
the shift lever to “E”, “M” or “R”.
11 02.18
AYGO WE 99E37E
—Warning functions

ENGINE (IGNITION) SWITCH, TRANSMISSION AND PARKING BRAKE155
MS16012
“1st” indicator blinking
In this case, shift the shift lever to the “E”
or “M” position once, then shift the shift
lever again to the “N” position.
MS16013
“R” indicator blinking
In this case, shift the shift lever to the
“R” position once, then shift the shift lever
again to the “N” position.
11 02.18
AYGO WE 99E37E

156ENGINE (IGNITION) SWITCH, TRANSMISSION AND PARKING BRAKE
Manual transmission
MS16001a
The shift pattern is as shown above.
Press the clutch pedal down fully while
shifting, and then release it slowly. Do not
rest your foot on the clutch pedal while
driving, because it will cause clutch
trouble. Do not use the clutch to hold the
vehicle when stopped on an uphill grade—
use the parking brake.
Upshifting too soon or downshifting too
late will cause lugging, and possibly ping-
ing. Regularly revving the engine to maxi-
mum speed in each gear will cause ex-
cessive engine wear and high fuel
consumption.
Maximum allowable speeds
To get on a highway or to pass slower
traffic, maximum acceleration may be nec-
essary. Make sure you observe the follow-
ing maximum allowable speeds in each
gear:
gear km/h (mph)
1 51 (31)
2 95 (59)
3 139 (86)
NOTICE
Do not downshift if you are going
faster than the maximum allowable
speed for the next gear down.
Good driving practice
If it is difficult to shift into reverse, put
the transmission in neutral, release the
clutch pedal momentarily, and then try
again.
CAUTION
Be careful when downshifting on a
slippery surface. Abrupt shifting
could cause the vehicle to skid or
spin.
NOTICE
zDo not use any gears other than
first gear when starting off and
moving forward. Doing so may dam-
age the clutch.
zMake sure the vehicle is completely
stopped before shifting into reverse.
11 02.18
AYGO WE 99E37E

ENGINE (IGNITION) SWITCH, TRANSMISSION AND PARKING BRAKE157
Traction control system
The traction control system automatical-
ly helps control the spinning of front
wheels when the vehicle is started or
accelerated on slippery road surfaces.
When the engine switch is turned to the
“ON” position, the system automatically
turns on.
CAUTION
Under certain slippery road condi-
tions, full traction of the vehicle and
power against front wheels cannot be
maintained, even though the traction
control system is in operation. Do not
drive the vehicle under any speed or
maneuvering conditions which may
cause the vehicle to lose traction
control. In situations where the road
surface is covered with ice or snow,
your vehicle should be fitted with
snow tires or tire chains. Always
drive at an appropriate and cautious
speed for the present road condi-
tions.
MS16014
Leave the system on during the ordi-
nary driving so that it can operate
when needed.
You may hear a sound in the engine
compartment for a few seconds when the
engine is started or just after the vehicle
begins to move. This means that the trac-
tion control system is in the self−check
mode, but does not indicate a malfunction.
When the traction control system isoper-
ating, the following conditions occur:
DThe system controls the spinning of the
front wheels. At this time, the slip indi-
cator light blinks.
DYou may feel vibration or noise in your
vehicle, caused by operation of the
brakes. This indicates the system is
functioning properly.
The slip indicator light comes on for a few
seconds when the engine switch is turned
to the “ON” position. If the indicator light
does not come on when the engine switch
is turned on, contact any authorized Toyo-
ta dealer or repairer, or another duly qual-
ified and equipped professional.
11 02.18
AYGO WE 99E37E

158ENGINE (IGNITION) SWITCH, TRANSMISSION AND PARKING BRAKE
ST16005
“VSC” warning light
This light warns that there is a problem
somewhere in the traction control system
or the vehicle stability control system.
The light will come on when the engine
switch is turned to the “ON” position and
will go off after a few seconds.
If the light comes on while driving, the
systemdoes not work. However, as con-
ventional braking operates when applied,
there is no problem to continue your driv-
ing.
In the following cases, contact any autho-
rized Toyota dealer or repairer, or another
duly qualified and equipped professional:
DThe warning light does not come on
after the engine switch is turned to the
“ON” position.
DThe warning light remains on after the
engine switch is turned to the “ON”
position.
DThe warning light comes on while driv-
ing.The vehicle stability controlsystem au-
tomatically controls the brakes and en-
gine to help prevent the vehicle from
skidding when cornering on a slippery
road surface or operating steering
wheel abruptly.
The vehicle stability control system is acti-
vated when the vehicle speed is more
than 15 km/h (9 mph).
You may hear a sound in the engine
compartment for a few seconds when the
engine is started or just after the vehicle
begins to move. This means that the sys-
tem is in the self−check mode but does
not indicate a malfunction.
CAUTION
DDo not rely excessively on the ve-
hicle stability controlsystem. Even
if the system is operating, you
must always drive carefully and at-
tentively. Reckless driving will re-
sult in an unexpected accident and
cause death or serious injury. If the
slip indicator light blinks, and spe-
cial care should be taken while
driving.
DOnly use tires of specified size. The
size, manufacture, brand and tread
pattern for all 4 tires should be the
same. If you use the tires other
than specified, or different type or
size, the vehicle stability control
system may not function correctly.
When replacing the tires or wheels,
contact any authorized Toyota deal-
er or repairer, or another duly quali-
fied professional. (See “Checking
and replacing tires” on page 270 in
Section 7−2.)
DIn situations where the road surface
is covered with ice or snow, your
vehicle should be fitted with snow
tire or tire chains.
11 02.18
AYGO WE 99E37E
Vehicle stability control
system

ENGINE (IGNITION) SWITCH, TRANSMISSION AND PARKING BRAKE159
MS16014
If the vehicle is going to skid during driv-
ing, the slip indicator light blinks. Special
care should be taken while driving.
The slip indicator light comes on for a few
seconds when the engine switch is turned
to the “ON” position. If the indicator light
does not come on when the engine switch
is turned on, contact any authorized Toyo-
ta dealer or repairer, or another duly qual-
ified and equipped professional.
ST16005
“VSC” warning light
This light warns that there is a problem
somewhere in the vehicle stability control
system or the traction control system.
The light will come on when the engine
switch is turned to the “ON” position and
will go off after a few seconds.
If the light comes on while driving, the
systemdoes not work. However, as con-
ventional braking operates when applied,
there is no problem to continue your driv-
ing.
In the following cases, contact any autho-
rized Toyota dealer or repairer, or another
duly qualified and equipped professional:
DThe warning light does not come on
after the engine switch is turned to the
“ON” position.
DThe warning light remains on after the
engine switch is turned to the “ON”
position.
DThe warning light comes on while driv-
ing.
11 02.18
AYGO WE 99E37E

160ENGINE (IGNITION) SWITCH, TRANSMISSION AND PARKING BRAKE
Parking brake
MS16002b
When parking, firmly apply the parking
brake to avoid inadvertent creeping.
To set: Pull up the lever. For better hold-
ing power, first depress the brake pedal
and hold it while setting the parking
brake.
To release: Pull up the lever slightly (1),
press the lock release button (2), and low-
er (3).
To remind you that the parking brake is
set, the parking brake reminder light in
the instrument cluster remains on until you
release the parking brake.
CAUTION
Before driving, be sure the parking
brake is fully released and the park-
ing brake reminder light is off.
11 02.18
AYGO WE 99E37E