transmission TOYOTA AYGO 2011 Owner's Guide

ENGINE (IGNITION) SWITCH, TRANSMISSION AND PARKING BRAKE157
Traction control system
The traction control system automatical-
ly helps control the spinning of front
wheels when the vehicle is started or
accelerated on slippery road surfaces.
When the engine switch is turned to the
“ON” position, the system automatically
turns on.
CAUTION
Under certain slippery road condi-
tions, full traction of the vehicle and
power against front wheels cannot be
maintained, even though the traction
control system is in operation. Do not
drive the vehicle under any speed or
maneuvering conditions which may
cause the vehicle to lose traction
control. In situations where the road
surface is covered with ice or snow,
your vehicle should be fitted with
snow tires or tire chains. Always
drive at an appropriate and cautious
speed for the present road condi-
tions.
MS16014
Leave the system on during the ordi-
nary driving so that it can operate
when needed.
You may hear a sound in the engine
compartment for a few seconds when the
engine is started or just after the vehicle
begins to move. This means that the trac-
tion control system is in the self−check
mode, but does not indicate a malfunction.
When the traction control system isoper-
ating, the following conditions occur:
DThe system controls the spinning of the
front wheels. At this time, the slip indi-
cator light blinks.
DYou may feel vibration or noise in your
vehicle, caused by operation of the
brakes. This indicates the system is
functioning properly.
The slip indicator light comes on for a few
seconds when the engine switch is turned
to the “ON” position. If the indicator light
does not come on when the engine switch
is turned on, contact any authorized Toyo-
ta dealer or repairer, or another duly qual-
ified and equipped professional.
11 02.18
AYGO WE 99E37E

158ENGINE (IGNITION) SWITCH, TRANSMISSION AND PARKING BRAKE
ST16005
“VSC” warning light
This light warns that there is a problem
somewhere in the traction control system
or the vehicle stability control system.
The light will come on when the engine
switch is turned to the “ON” position and
will go off after a few seconds.
If the light comes on while driving, the
systemdoes not work. However, as con-
ventional braking operates when applied,
there is no problem to continue your driv-
ing.
In the following cases, contact any autho-
rized Toyota dealer or repairer, or another
duly qualified and equipped professional:
DThe warning light does not come on
after the engine switch is turned to the
“ON” position.
DThe warning light remains on after the
engine switch is turned to the “ON”
position.
DThe warning light comes on while driv-
ing.The vehicle stability controlsystem au-
tomatically controls the brakes and en-
gine to help prevent the vehicle from
skidding when cornering on a slippery
road surface or operating steering
wheel abruptly.
The vehicle stability control system is acti-
vated when the vehicle speed is more
than 15 km/h (9 mph).
You may hear a sound in the engine
compartment for a few seconds when the
engine is started or just after the vehicle
begins to move. This means that the sys-
tem is in the self−check mode but does
not indicate a malfunction.
CAUTION
DDo not rely excessively on the ve-
hicle stability controlsystem. Even
if the system is operating, you
must always drive carefully and at-
tentively. Reckless driving will re-
sult in an unexpected accident and
cause death or serious injury. If the
slip indicator light blinks, and spe-
cial care should be taken while
driving.
DOnly use tires of specified size. The
size, manufacture, brand and tread
pattern for all 4 tires should be the
same. If you use the tires other
than specified, or different type or
size, the vehicle stability control
system may not function correctly.
When replacing the tires or wheels,
contact any authorized Toyota deal-
er or repairer, or another duly quali-
fied professional. (See “Checking
and replacing tires” on page 270 in
Section 7−2.)
DIn situations where the road surface
is covered with ice or snow, your
vehicle should be fitted with snow
tire or tire chains.
11 02.18
AYGO WE 99E37E
Vehicle stability control
system

ENGINE (IGNITION) SWITCH, TRANSMISSION AND PARKING BRAKE159
MS16014
If the vehicle is going to skid during driv-
ing, the slip indicator light blinks. Special
care should be taken while driving.
The slip indicator light comes on for a few
seconds when the engine switch is turned
to the “ON” position. If the indicator light
does not come on when the engine switch
is turned on, contact any authorized Toyo-
ta dealer or repairer, or another duly qual-
ified and equipped professional.
ST16005
“VSC” warning light
This light warns that there is a problem
somewhere in the vehicle stability control
system or the traction control system.
The light will come on when the engine
switch is turned to the “ON” position and
will go off after a few seconds.
If the light comes on while driving, the
systemdoes not work. However, as con-
ventional braking operates when applied,
there is no problem to continue your driv-
ing.
In the following cases, contact any autho-
rized Toyota dealer or repairer, or another
duly qualified and equipped professional:
DThe warning light does not come on
after the engine switch is turned to the
“ON” position.
DThe warning light remains on after the
engine switch is turned to the “ON”
position.
DThe warning light comes on while driv-
ing.
11 02.18
AYGO WE 99E37E

160ENGINE (IGNITION) SWITCH, TRANSMISSION AND PARKING BRAKE
Parking brake
MS16002b
When parking, firmly apply the parking
brake to avoid inadvertent creeping.
To set: Pull up the lever. For better hold-
ing power, first depress the brake pedal
and hold it while setting the parking
brake.
To release: Pull up the lever slightly (1),
press the lock release button (2), and low-
er (3).
To remind you that the parking brake is
set, the parking brake reminder light in
the instrument cluster remains on until you
release the parking brake.
CAUTION
Before driving, be sure the parking
brake is fully released and the park-
ing brake reminder light is off.
11 02.18
AYGO WE 99E37E

194INFORMATION BEFORE DRIVING YOUR TOYOTA
Break−in period
Drive gently and avoid high speeds.
Your vehicle does not need an elaborate
break−in. But following a few simple tips
for the first 1000 km (600 miles) can add
to the future economy and long life of
your vehicle:
DAvoid full throttle acceleration when
starting and driving.
DAvoid racing the engine.
DTry to avoid hard stops during the first
300 km (200 miles).
DDo not drive slowly with the manual
transmission in a high gear.
DDo not drive for a long time at any
single speed, either fast or slow.
Fuel
Selecting the proper fuel is essential
for satisfactory engine performance.
Engine damage caused by use of improp-
er fuels is not covered under Toyota’s new
vehicle warranty.
NOTICE
zDo not use improper fuels. If im-
proper fuels are used the engine
will be damaged.
zDo not use leaded gasoline on your
vehicle. Use of leaded gasoline will
cause damage to the engine. Also,
this can increase maintenance
costs.
zEU area: Bioethanol fuel sold under
names such as “E50” or “E85” and
fuel containing a large amount of
ethanol should not be used. The
use of these fuels will damage the
vehicle’s fuel system. In case of
any doubt, ask any authorized
Toyota dealer or repairer, or
another duly qualified and equipped
professional.
zExcept EU area: Bioethanol fuel
sold under names such as “E50” or
“E85” and fuel containing a large
amount of ethanol should not be
used. Your vehicle can use gasoline
mixed with 10% max ethanol. The
use of fuel with more than 10%
ethanol content (E10) will damage
the vehicle’s fuel system. You must
ensure that refueling is carried out
only from a source where fuel spec-
ification and quality can be guaran-
teed. In case of any doubt, ask any
authorized Toyota dealer or repairer,
or another duly qualified and
equipped professional.
AYGO WE 99E37E11 02.18

210STARTING AND DRIVING
Before starting the engine
1. Check the area around the vehicle be-
fore entering it.
2. Adjust the seat position, seatback
angle and steering wheel angle.
3. Adjust the inside and outside rear view
mirrors.
4. Close all doors.
5. Fasten seat belts.1. Apply the parking brake firmly.
2. Turn off unnecessary lights and acces-
sories.
3.Multi−mode manual transmission:
Turn the engine switch to “ON” posi-
tion. Hold down the brake pedal firmly,
and place the shift lever to the “N”
position. Make sure that the “N” indi-
cator in the instrument cluster comes
on. A starter safety device will prevent
the starter from operating if the shift
lever is in a position except “N” or the
brake pedal is not depressed.
Manual transmission:Press the clutch
pedal to the floor and shift the trans-
mission into neutral. Hold the clutch
pedal to the floor until the engine is
started. A starter safety device will pre-
vent the starter from operating if the
clutch pedal is not fully depressed.
AYGO WE 99E37E11 02.18
How to start the engine
(a) Before cranking

STARTING AND DRIVING211
Before starting the engine, be sure to
follow the instructions in “(a) Before
cranking”.
Normal starting procedure
The multiport fuel injection system/sequen-
tial multiport fuel injection system in your
engine automatically controls the proper
air−fuel mixture for starting. You can start
a cold or hot engine as follows:
Multi−mode manual transmission:With
your foot off the accelerator pedal, turn
the engine switch to the “START” posi-
tion and crank the engine while depress-
ing the brake pedal. Release the key
when the engine starts. The engine can-
not be cranked if the shift lever is in a
position except “N” or the brake pedal
is not depressed.
Manual transmission:With your foot off
the accelerator pedal, crank the engine
by turning the engine switch to the
“START” position. Release it when the
engine starts.
Engine should be warmed up by driving,
not idling. For warming up drive with a
smoothly turning engine until the engine
coolant temperature is within the normal
range.
If the engine stalls...
Simply restart it, using the correct proce-
dure given in normal starting.
If the engine will not start...
See “If your vehicle will not start” on page
220 in Section 4.
NOTICE
zDo not crank for more than 30 se-
conds at a time. This may overheat
the starter and wiring systems.
zDo not race a cold engine.
zIf the engine becomes difficult to
start or stalls frequently, have the
engine checked immediately.
Pre−trip safety check
It is a good idea to do a safety check
before starting out on a trip. A few min-
utes of checking can help ensure safe and
pleasant driving. Just a basic familiarity
with your vehicle is required and a careful
eye! Or, if you would like, any authorized
Toyota dealer or repairer, or another duly
qualified and equipped professional, will
be pleased to make this check for you at
nominal cost.
CAUTION
If you make this check in an enclosed
garage, make sure there is adequate
ventilation. Engine exhaust is poison-
ous.
BEFORE STARTING THE ENGINE
Outside the vehicle
Tires.Check the pressure with a gauge
and look carefully for cuts, damage, or
excessive wear.
Wheel bolts.Make sure no bolts are mis-
sing or loose.
Fluid leaks.After the vehicle has been
parked for a while, check underneath for
leaking fuel, oil, water, or fluid. (Water
dripping from the air conditioning after use
is normal.)
Lights.Make sure the headlights, stop
lights, tail lights, turn signals and other
lights are all working. Check the headlight
aim.
Inside the vehicle
Spare tire, jack and wheel bolt wrench.
Check the spare tire pressure and make
sure you have your jack and wheel bolt
wrench.
AYGO WE 99E37E11 02.18
(b) Starting the engine

STARTING AND DRIVING213
DAlways slow down in gusty crosswinds.
This will allow you much better control.
DDrive slowly onto curbs and, if pos-
sible, at a right angle. Avoid driving
onto high, sharp−edged objects and
other road hazards. Failure to do so
can lead to severe tire damage such
as a tire burst.
Drive slowly when passing over bumps
or travelling on a bumpy road. Other-
wise, the impact could cause severe
damage to the tires and/or wheels.
DWhen parking on a hill, turn the front
wheels until they touch the curb so
that the vehicle will not roll. Apply the
parking brake, and place the transmis-
sion in “M(1)”, “E(1)” or “R” (multi−
mode manual transmission), or first or
reverse (manual transmission). If nec-
essary, block the wheels.
DWashing your vehicle or driving through
deep water may get the brakes wet. To
see whether they are wet, check that
there is no traffic near you, and then
press the pedal lightly. If you do not
feel a normal braking force, the brakes
are probably wet. To dry them, drive
the vehicle cautiously while lightly
pressing the brake pedal with the park-
ing brake applied. If they still do not
work safely, pull to the side of the road
and call any authorized Toyota dealer
or repairer, or another duly qualified
and equipped professional, for assis-
tance.
CAUTION
DBefore driving off, make sure the
parking brake is fully released and
the parking brake reminder light is
off.
DDo not leave your vehicle unat-
tended while the engine is running.
DDo not rest your foot on the brake
pedal while driving. It can cause
dangerous overheating, needless
wear, and poor fuel economy.
DTo drive down a long or steep hill,
reduce your speed and downshift.
Remember, if you ride the brakes
excessively, they may overheat and
not work properly.
DBe careful when accelerating, up-
shifting, downshifting or braking on
a slippery surface. Sudden accelera-
tion or engine braking could cause
the vehicle to skid or spin.
DDo not continue normal driving
when the brakes are wet. If they are
wet, your vehicle will require a
longer stopping distance, and it
may pull to one side when the
brakes are applied. Also, the park-
ing brake will not hold the vehicle
securely.
NOTICE
zDo not depress the accelerator and
brake pedals at the same time dur-
ing driving. If the brake pedal is
depressed while driving with the ac-
celerator pedal depressed, driving
torque may be restrained.
zDo not use the accelerator pedal or
depress the accelerator and brake
pedals at the same time to hold the
vehicle on a hill.
AYGO WE 99E37E11 02.18
Tips for driving in various
conditions

STARTING AND DRIVING215
Winter driving tips
Make sure your coolant is properly pro-
tected against freezing.
Only use “Toyota Super Long Life Coolant”
or similar high quality ethylene glycol
based non−silicate, non−amine, non−nitrite,
and non−borate coolant with long−life hy-
brid organic acid technology. (Coolant with
long−life hybrid organic acid technology is
a combination of low phosphates and or-
ganic acids.)
See “Checking the engine coolant level”
on page 267 in Section 7−2 for details of
coolant type selection.
“Toyota Super Long Life Coolant” is a mix-
ture of 50% coolant and 50% deionized
water. This coolant provides protection
down to about−35_C(−31_F).
NOTICE
Do not use plain water alone.
Check the condition of the battery and
cables.
Cold temperatures reduce the capacity of
any battery, so it must be in top shape
to provide enough power for winter start-
ing. Section 7−3 tells you how to visually
inspect the battery. Any authorized Toyota
dealer or repairer, or another duly quali-
fied and equipped professional, will be
pleased to check the level of charge.
Make sure the engine oil viscosity is
suitable for the cold weather.
See page 264 in Section 7−2forrecom-
mended viscosity. Leaving a heavy sum-
mer oil in your vehicle during winter
months may make starting harder. If you
are not sure about which oil to use, call
any authorized Toyota dealer or repairer,
or another duly qualified and equipped
professional, they will be pleased to help.
Keep the door locks from freezing.
Squirt lock de−icer or glycerine into the
locks to keep them from freezing.Use a washer fluid containing an anti-
freeze solution.
This product is available at any authorized
Toyota dealer or repairer and most auto
parts stores or another qualified profes-
sional. Follow the manufacturer ’s direc-
tions for how much to mix with water.
NOTICE
Do not use engine antifreeze or any
other substitute because it may dam-
age your vehicle’s paint.
Do not use your parking brake when
there is a possibility it could freeze.
When parking, put the transmission into
“M(1)”, “E(1)” or “R” (multi−mode manual
transmission), or into first or reverse
(manual transmission) and block the rear
wheels. Do not use the parking brake,
snow or water accumulated in and around
the parking brake mechanism may freeze,
making it hard to release.
Keep ice and snow from accumulating
under the fenders.
Ice and snow built up under your fenders
can make steering difficult. During bad
winter driving, stop and check under the
fenders occasionally.
Depending on where you are driving,
we recommend you carry some emer-
gency equipment.
Some of the things you might put in the
vehicle are tire chains, a window scraper,
a bag of sand or salt, flares, a small
shovel, jumper cables, etc.
AYGO WE 99E37E11 02.18

IN CASE OF AN EMERGENCY219
Section 4
IN CASE OF AN EMERGENCY
DIf your vehicle will not start 220..............................
DIf your engine stalls while driving 224........................
DIf you cannot increase engine speed 225.....................
DIf your vehicle overheats 225...............................
DIf you have a flat tire 226...................................
DIf your vehicle becomes stuck 236...........................
DIf your vehicle needs to be towed 236........................
DIf you cannot shift multi−mode manual transmission
shift lever 242.............................................
DIf you lose your keys 243...................................
DIf your vehicle has to be stopped in an emergency 244........
AYGO WE 99E37E11 02.18