CD player TOYOTA AYGO 2011 Owners Manual

OCCUPANT RESTRAINT SYSTEMS53
NOTICE
Do not perform any of the following
changes without consulting any
authorized Toyota dealer or repairer,
or another duly qualified and
equipped professional. Such changes
can interfere with proper operation of
the seat belt pretensioners in some
cases.
zInstallation of electronic devices
such as an RF−transmitter, cassette
tape player or compact disc player
zRepairs on or near the front seat
belt retractor assemblies
zModification of the suspension sys-
tem
zModification of the front end struc-
ture
zAttachment of a grille guard (bull
bar, kangaroo bar, etc.), snowplow,
winches or any other equipment to
the front end
zRepairsmadeonornearthefront
fenders, front end structure or con-
sole
MS13089
This indicator comes on when the en-
gine switch is turned to the “ON” posi-
tion. It goes off after about 6 seconds.
This means the seat belt pretensioners
are operating properly.
This warning light system monitors the
airbag sensor assembly, side airbag
sensors, side and curtain shield airbag
sensors, airbag manual on−off switch, seat
belt pretensioner assemblies, inflators,
warning light, interconnecting wiring and
power sources. (For details, see “Service
reminder indicators and warning buzzers”
on page 127 in Section 1−6.)
If any of the following conditions occurs,
this indicates a malfunction of the airbags
or seat belt pretensioners. Contact any
authorized Toyota dealer or repairer, or
another duly qualified and equipped
professional, as soon as possible.
DIf any front seat belt does not retract
or cannot be pulled out due to a mal-
function or activation of the relevant
seat belt pretensioner.
DThe seat belt pretensioner assembly or
surrounding area has been damaged.
The airbag manual on−offswitchisinthe
“ON” position:
DWhen the engine switch is turned to
the “ON” position, the light comes on
for more than 6 seconds and then
flashes.
AYGO WE 99E37E11 02.18

60OCCUPANT RESTRAINT SYSTEMS
MS13030
DDo not put anything or any part of
your body on or in front of the
dashboard or steering wheel pad
that houses the front airbag sys-
tem. They might restrict inflation or
cause death or serious injury as
they are projected rearward by the
force of the deploying airbags. Like-
wise, the driver and front passenger
should not hold objects in their
arms or on their knees.
DDo not modify or remove any wir-
ing. Do not modify, remove, strike
or open any components such as
the steering wheel pad, steering
wheel, column cover, front passen-
ger airbag cover, front passenger
airbag or airbag sensor assembly.
Doing so may prevent the front air-
bag system from activating correct-
ly, cause sudden activation of the
system or disable the system,
which could result in death or seri-
ous injury.
Failure to follow these instructions
can result in death or serious injury.
Consult any authorized Toyota dealer
or repairer, or another duly qualified
and equipped professional, about any
repair and modification.
NOTICE
Do not perform any of the following
changes without consulting any autho-
rized Toyota dealer or repairer, or
another duly qualified and equipped
professional. Such changes can inter-
fere with proper operation of the SRS
front airbag system in some cases.
zInstallation of electronic devices
such as an RF−transmitter, cassette
tape player or compact disc player
zModification of the suspension sys-
tem
zModification of the front end struc-
ture
zAttachment of a grille guard (bull
bar, kangaroo bar, etc.), snowplow,
winches or any other equipment to
the front end
zRepairsmadeonornearthefront
fenders, front end structure, con-
sole, steering column, steering
wheel or dashboard near the front
passenger airbag
AYGO WE 99E37E11 02.18

66OCCUPANT RESTRAINT SYSTEMS
MS13035
DDo not attach a cup holder or any
other device or object on or around
the door. When the side airbag in-
flates, the cup holder or any other
device or object will be thrown with
great force or the side airbag may
not activate correctly, resulting in
death or serious injury. Likewise,
the driver and front passenger
should not hold objects in their
arms or on their knees.
DDo not use seat accessories which
cover the parts where the side air-
bags inflate. Such accessories may
prevent the side airbags from acti-
vating correctly, causing death or
serious injury.
DDo not modify or replace the seats
or upholstery of the seats with side
airbags. Such changes may prevent
the side airbag system from activat-
ing correctly, disable the system or
cause the side airbags to inflate ac-
cidentally, resulting in death or seri-
ous injury.
Failure to follow these instructions
can result in death or serious injury.
Consult any authorized Toyota dealer
or repairer, or another duly qualified
and equipped professional, about any
repair and modification.
NOTICE
Do not perform any of the following
changes without consulting any autho-
rized Toyota dealer or repairer, or
another duly qualified and equipped
professional. Such changes can inter-
fere with proper operation of the SRS
side airbag system in some cases.
zInstallation of electronic devices
such as an RF−transmitter, cassette
tape player or compact disc player
zModification of the suspension sys-
tem
zModification of the side structure of
the passenger compartment
zRepairsmadeonornearthecon-
sole or front seat
AYGO WE 99E37E11 02.18

OCCUPANT RESTRAINT SYSTEMS75
MS13087
DDo not attach a microphone or any
other device or object around the
area where the curtain shield airbag
activates such as on the windshield
glass, side door glass, front, center
and rear pillars, roof side rail and
roof headlining. When the curtain
shield airbag inflates, the micro-
phone or other device or object will
be thrown away with great force or
the curtain shield airbag may not
activate correctly, resulting in death
or serious injury.
DDo not use seat accessories which
cover the parts where the side air-
bags inflate. Such accessories may
prevent the side airbags from acti-
vating correctly, causing death or
serious injury.
DDo not modify or replace the seats
or upholstery of the seats with side
airbags. Such changes may prevent
the side airbag system from activat-
ing correctly, disable the system or
cause the side airbags to inflate ac-
cidentally, resulting in death or seri-
ous injury.
DDo not disassemble or repair the
front, center and rear pillars, roof
side rail and roof headlining con-
taining the curtain shield airbags.
Such changes may disable the sys-
tem or cause the curtain shield air-
bags to inflate accidentally, result-
ing in death or serious injury.
Failure to follow these instructions
can result in death or serious injury.
Consult any authorized Toyota dealer
or repairer, or another duly qualified
and equipped professional, about any
repair and modification.
NOTICE
Do not perform any of the following
changes without consulting any autho-
rized Toyota dealer or repairer, or
another duly qualified and equipped
professional. Such changes can inter-
fere with proper operation of the SRS
side airbag and curtain shield airbag
system in some cases.
zInstallation of electronic devices
such as an RF−transmitter, cassette
tape player or compact disc player
zModification of the suspension sys-
tem
zModification of the side structure of
the passenger compartment
zRepairsmadeonornearthecon-
sole or front seat
AYGO WE 99E37E11 02.18

162AUDIO SYSTEM
Reference
MS17001
AM·FM radio/compact disc player (with
compact disc changer controller)
This Section describes some of the basic
features on Toyota audiosystems. Some
information may not pertain to your sys-
tem.
Your audiosystem works when theengine
switch is in the “ACC” or “ON” position.
TURNING THE SYSTEM ON AND OFF
Push “
” (Power) to turn the audio sys-
tem on and off. The audio power can be
turned on only once even when the key
is not in the engine switch. The power,
however, will automatically turn off when
30 minutes have elapsed.
Push “AM/FM” or “CD/AUX” to turn on
that function without pushing “
” (Power).
You can turn on the compact disc player
by inserting a compact disc.
You can turn off each player by ejecting
the compact disc. If the audiosystem was
previously off, then the entire audio sys-
tem will be turned off when you eject the
compact disc. If another function was pre-
viously on, it will come on again.
SWITCHING BETWEEN FUNCTIONS
Push “AM/FM” or “CD/AUX” if the system
is already on but you want to switch from
one function to another.
VOLUME CONTROL
To adjust the volume, push and release
“”or“” side of the “VOL” button.
AYGO WE 99E37E11 02.18
Using your audio system—
—Some basics

AUDIO SYSTEM163
AUDIO CONTROL
This function is to adjust the tone or bal-
ance. Push the “AUDIO CONT” button to
switch to the audio control mode. To
switch to the BAS, TRE, FAD, or BAL,
push the “AUDIO CONT” button. To adjust
each mode, push the “TUNE/TRACK (
)” button.
BAS: Adjusts low−pitched tones
TRE: Adjusts high−pitched tones
FAD: Adjusts the sound balance be-
tween the instrument panel and
front door speakers
BAL: Adjusts the sound balance be-
tween the right and left speakers
YOUR RADIO ANTENNA
To remove an antenna, carefully turn it
counterclockwise.
NOTICE
zTo prevent damage to the antenna,
be sure to remove it before driving
your Toyota through an automatic
car wash.
zWhen storing the vehicle in a ga-
rage, remove the antenna if it
touches the ceiling.
YOUR COMPACT DISC PLAYER
When you insert a disc, gently push it in
with the label side up. The compact disc
player will play from track 1 through to
the end of the disc. Then it will play from
track 1 again.
NOTICE
Never try to disassemble or oil any
part of the compact disc player. Do
not insert anything other than com-
pact discs into the slot.
The player is intended for use with 12 cm
(4.7 in.) disc only.
MS17003
AUX
Portable music players, such as compact
disc and MD players, can be listened to
through the car stereo speakers by con-
necting a player to the AUX port located
on the audio front panel.
AYGO WE 99E37E11 02.18

AUDIO SYSTEM165
123456(Preset buttons)
These buttons are used to preset and
tune in radio stations.
To preset a station to a button: Tune in
the desired station. (See “TUNE/TRACK”
button). Push and hold down the button
until you hear a beep—this will set the
station to the button. The button number
will appear on the display.
To recall a preset station: Push the button
for the station you want. The button num-
ber and station frequency will appear on
the display.
These systems can store one AM and
three FM station for each button. (The
display will show “AM”, “FM1”, “FM2” or
“FM3” when you push “AM/FM”.) The pre-
set station memory will be canceled out
if the power source is interrupted. (Battery
disconnected or fuse blown.)
(Eject button)
Push this button to eject a compact disc.
After you turn the engine switch to
“LOCK”, you will be able to eject a com-
pact disc but you will not be able to rein-
sert it.
TUNE/TRACK (Tuning/Track up/down)
Radio
Tuning:
Quickly push and release the “”or“”
button. Each time you push the button,
the radio will step up or down to another
frequency. If you hear a beep, you held
the button too long and the radio will go
into the seek mode.Seeking:
Push and hold the “”or“” until you
hear a beep. The radio will begin seeking
up or down for a station of the nearest
frequency and will stop on reception. Each
time you push the button, the stations will
be searched automatically one after anoth-
er.
Compact disc player
By using this button, you can either skip
up/down to a different track or fast for-
ward/reverse the track you are listening
to.
Skip up/down tracks:
Quickly push and release the “”or“”
button. The track number will appear on
the display. If you hear a beep, you held
the button too long, and the player will
fast forward or reverse a track.
Fast forward/reverse tracks:
Push and hold the “
”or“” until
you hear a beep. While you are holding
the button, the player will fast forward/re-
verse the track. When you release the
button, the player will resume playing.
“
”(Power)
Push “
” to turn the audiosystem on
and off. The audio power can be turned
on only once even when the key is not
in the engine switch. The power, however,
will automatically turn off when 30 minutes
have elapsed.
VOL (Volume)
The volume can be adjusted by pushing
the “”or“” button.
AYGO WE 99E37E11 02.18

AUDIO SYSTEM167
CD/AUX
CD (Compact Disc)
Push “CD/AUX” to switch from radio op-
eration to compact disc operation. If the
audiosystem is off, you can turn on the
compact disc player by pushing “CD/AUX”.
In both cases, a disc must already be
loaded in the player.
The player will automatically start when
you insert a compact disc. At this time,
“CD” appears on the display.
When the audio is set into compact disc
operation, the display shows the track or,
track and disc number currently being
played. Each time you push “CD/AUX”,
the system changes between single disc
player and compact disc changer.
If the player malfunctions, your audio sys-
tem will display following error messages.
If “WAIT” appears on the display,it indi-
cates that the inside of the player unit
may be too hot due to the very high ambi-
ent temperature. Remove the disc or mag-
azine from the player and allow the player
to cool down.
If “Err 1” appears on the display,it
indicates the disc is dirty, damaged, or it
was inserted up−side down. Clean the
disc or insert it correctly.
If “Err 2” appears on the display,it
indicates no disc is loaded inside the
magazine, insert a disc.
If “Err 3” appears on the display,it
indicates there is a trouble inside the sys-
tem. Eject the disc or magazine. Set the
disc or magazine again.
If “Err 4” appears on the display,over−
current. Ask any authorized Toyota dealer
or repairer, or another duly qualified and
equipped professional, to inspect.
If “OPEn” appears on the display,it
indicates the compact disc changer lid is
open. Close the compact disc changer lid.If the malfunction is not rectified,take
your vehicle to any authorized Toyota
dealer or repairer, or another duly quali-
fied and equipped professional.
AUX
In order to listen to a portable music play-
er, such as a compact disc or MD player,
through the car stereo speakers, push the
“CD/AUX” button after it has been con-
nected to the AUX port on the audio front
panel.
DISC
Compact disc changer only—
By using this button, you can select a
discyouwishtolistento.
Push either side of the button until the
number of the disc you want to listen to
appears on the display.
PTY (Program Type)
Push “PTY”. If the button is pushed while
receiving a PTY code of the RDS station,
the current program type (“NEWS”,
“SPORTS”, “TALK”, “POP”, “CLASSICS”)
will appear on the display. If another pro-
gram type is desired, push “PTY” until
your desired program type appears.
If no PTY code of RDS station is re-
ceived, “NO PTY” will appear on the dis-
play.
If either “”or“” side of the “TUNE/
TRACK” button is pushed while the pro-
gram type is appeared on the display, the
radio will search a station that carries
PTY code. If the radio cannot seek out
any stations, “NOTHING” will appear on
the display.
AYGO WE 99E37E11 02.18

168AUDIO SYSTEM
If the system is left untouched for 6 sec-
onds while the program type is displayed,
or if another operation is made, the pro-
gram type display will disappear and the
radio will broadcast a program of the last
program type displayed.
RAND (Random)
There are two random features—you can
either listen to the tracks on all the com-
pact discs in the magazine in random or-
der, or only listen to the tracks on a
specific compact disc in random order.
To randomly play the tracks on a disc:
Quickly push and release “RAND”. “RAND”
will appear on the display. The disc you
are listening to will play in random order.
If you hear a beep, you held the button
too long, and the player will play all the
tracks in the magazine in random order.
To turn off the random feature, push the
“RAND” a second time.
Compact disc changer only—
To randomly play all the tracks in the
magazine:
Push and hold “RAND” until you hear a
beep. “D−RAND” will appear on the dis-
play and the player will perform all the
tracks on all the discs in the magazine in
random order. To turn off the random fea-
ture, push “RAND” a second time.RPT (Repeat)
There are two repeat features—you can
either replay a disc track or a whole com-
pact disc.
Repeating a track:
Quickly push and release “RPT” while the
track is playing. “RPT” will appear on the
display. If you hear a beep, you held the
button too long, and the player will repeat
the whole disc. When the track ends, it
will automatically be replayed. This pro-
cess will be continued until you push the
button again to turn off the repeat feature.
Compact disc changer only—
Repeating a disc:
Push and hold “RPT” until you hear a
beep. “D−RPT” will appear on the display.
The player will repeat all the tracks on the
disc you are listening to. When the disc
ends, the player will automatically go back
to the first track on the disc and replay.
This process will be continued until you
push the button again to turn off the re-
peat feature.
AYGO WE 99E37E11 02.18

AUDIO SYSTEM169
SCAN
There are two scan features—you can ei-
ther scan the tracks on a specific disc or
scan the first tracks of all the discs in the
magazine.
Scanning the tracks on a disc:
Quickly push and release “SCAN”. “SCAN”
will appear on the display and the player
will scan all the tracks on the disc you
are listening to. If you hear a beep, you
held the button too long, and the player
will scan the first tracks of all the discs
in the magazine. To select a track, push
the “SCAN” a second time. If the player
scanned all the tracks on the disc, it will
stop scanning.
Compact disc changer only—
Scanning for the first tracks of all the
discs in the magazine:
Push and hold “SCAN” until you hear a
beep. “D−SCAN” will appear on the dis-
play and the player will perform the first
track of the next disc. To select a disc,
push the “SCAN” a second time. If the
player has scanned all the discs, it will
stop scanning.
ST (Stereo reception) display
Your radio automatically changes to stereo
reception when a stereo broadcast is re-
ceived. “ST” appears on the display. If the
signal becomes weak, the radio reduces
the amount of channel separation to prev-
ent the weak signal from creating noise.
If the signal becomes extremely weak, the
radio switches from stereo to mono recep-
tion.TA (Traffic Announcement)
This button is used for receiving TA sta-
tions all over the band.
EON (Enhanced Other Network) sys-
tem—If the RDS station (with EON data)
you are listening to is not broadcasting a
traffic information program at the TA (Traf-
fic Announcement) mode, the radio will be
switched to the traffic information program
automatically by using the EON AF list.
After the traffic information ends, the radio
will return to the initial program automati-
cally. A beep will sound to tell you when
this feature starts and ends the operation.
When receiving FM:
Push “TA” to switch the radio mode to TP
(Traffic Program). “TP” will appear on the
display.
In the TP mode, the radio will begin seek-
ing a TP station. If the radio seek out a
TP station, the program name will appear
on the display. If the TA station is re-
ceived, the radio will be switched to the
traffic information program automatically.
When the program ends, the initial opera-
tion resumes. When also in AF mode, the
radio will seek a TP station by using the
AF list.
Push “TA” once again to switch the radio
mode to TA. “TA” will appear on the dis-
play and the radio will mute the volume
of FM station.
In the TA mode, the radio will begin seek-
ing a TP station. It sounds only when a
TP station is received. When a TP station
is received, the program service name will
appear on the display. In the AF mode,
the radio will also begin seeking a TP
station by using the AF list.
While the radio is seeking a TP station,
“TP SEEK” appears on the display. If the
radio cannot seek out any TP stations,
“NOTHING” will appear on the display for
2 seconds and the radio will begin seek-
ing a TP station again.
AYGO WE 99E37E11 02.18