TOYOTA CAMRY 1999 Service Repair Manual

AUTOMATIC TRANSAXLEUPPER VALVE BODY ±
AX±81
UPPER VALVE BODY
COMPONENTS
AX0GA±02

AUTOMATIC TRANSAXLEUPPER VALVE BODY ±
AX±82
VALVE BODY SPRINGS SPECIFICATIONS
HINT: During re±assembly please refer to the spring specifications below to help you to discriminate
between the different springs.
Spring (Color)Free Length / Coil Outer Diameter
mm (in.)Number of Coils
@@
@@
@:
[c A]
Throttle Modulator Spring (None)21.70 / 9.50 (0.8543 / 0.3740)9.5
@@
@@
@:
[c B]
Accumulator Control Spring (Yellow)28.06 / 10.60 (1.1047 / 0.4173)13.0
@@
@@
@:
[c C]
Low Coast Modulator Spring (None)21.60 / 7.90 (0.8504 / 0.3110)11.5
@@
@@
@:
[c D]
Down Shift Valve Spring (Yellow)29.76 / 8.73 (1.1717 / 0.3437)13.5
AX0GB±02

AUTOMATIC TRANSAXLEUPPER VALVE BODY ±
AX±83
@@
@@
@:
[c E]
Throttle Valve Spring (None)30.70 / 9.20 (1.2087 / 0.3622)9.5
@@
@@
@:
[c F]
Second Coast Modulator Valve Spring
(Light Green)20.93 / 8.50 (0.8240 / 0.3364)10.0
@@
@@
@:
[c G]
Lock±up Relay Valve spring (Green)26.56 / 10.20 (1.0457 / 0.4016)11.5
@@
@@
@:
[c H]
Cut±back Valve Spring (None)21.80 / 6.00 (0.8583 / 0.2362)13.5

AUTOMATIC TRANSAXLEUPPER VALVE BODY ±
AX±84
RETAINERS, PINS, VIBRATING STOPPER AND CHECK BALLS LOCATION
RetainerHeight / Width / Thickness
mm (in.)
@@@@@: [c H]Throttle Modulator Valve9.2 / 5.0 / 3.2 (0.362 / 0.197 / 0.126)
@@@@@: [c I]Accumulator Control Valve11.5 / 5.0 / 3.2 (0.453 / 0.197 / 0.126)
@@@@@: [c J]Cut±back Valve9.2 / 5.0 / 3.2 (0.362 / 0.197 / 0.126)
@@@@@: [c K]Lock±up Relay Valve15.0 / 5.0 / 3.2 (0.591 / 0.197 / 0.126)
@@@@@: [c L]2nd Coast Modulator Valve15.0 / 5.0 / 3.2 (0.591 / 0.197 / 0.126)
AX0GC±02

AUTOMATIC TRANSAXLELOWER VALVE BODY ±
AX±85
LOWER VALVE BODY
COMPONENTS
AX0GV±02

AUTOMATIC TRANSAXLELOWER VALVE BODY ±
AX±86
VALVE BODY SPRINGS SPECIFICATIONS
HINT: During re±assembly please refer to the spring specifications below to help you to discriminate
between the different springs.
Spring (Color)Free length / Outer diameter
mm (in.)Number of Coils
@@
@@
@:
[c A]
Secondary Regulator Valve Spring
(None)43.60 / 10.90 (1.7165 / 0.4291)11.5
@@
@@
@:
[c B]
Lock±up Signal Valve Spring (None)30.00 / 8.20 (1.1811 / 0.3228)11.5
@@
@@
@:
[c C]
3±4 Shift Valve Spring (None)29.27 / 9.70 (1.1524 / 0.3819)10.5
AX0GD±02

AUTOMATIC TRANSAXLELOWER VALVE BODY ±
AX±87
@@
@@
@:
[c D]
1±2 Shift Valve Spring (None)29.27 / 9.70 (1.1524 / 0.3819)10.5
@@
@@
@:
[c E]
2±3 Shift Valve Spring (None)29.27 / 9.70 (1.1524 / 0.3819)10.5
@@
@@
@:
[c F]
Primary Regulator Valve Spring (None)66.65 / 18.60 (2.6240 / 0.7323)12.5
@@
@@
@:
[c G]
Cooler By±pass Valve Spring (None)19.90 / 11.00 (0.7835 / 0.4331)8.5
@@
@@
@:
[c H]
Pressure Relief Valve Spring (None)11.20 / 6.40 (0.4409 / 0.2520)7.5

AUTOMATIC TRANSAXLELOWER VALVE BODY ±
AX±88
RETAINER, STRAINER AND CHECK BALLS LOCATION
RetainerHeight / Width / Thickness
mm (in.)
@@@@@: [c I]Primary Regulator Valve9.2 / 5.0 / 3.2 (0.362 / 0.197 / 0.128)
@@@@@: [c J]2±3 Shift Valve8.0 / 6.0 / 3.2 (0.315 / 0.236 / 0.126)
@@@@@: [c K]1±2 Shift Valve9.2 / 5.0 / 3.2 (0.362 / 0.197 / 0.126)
@@@@@: [c L]3±4 Shift Valve8.0 / 6.0 / 3.2 (0.315 / 0.236 / 0.126)
@@@@@: [c M]Secondary Regulator Valve13.0 / 6.0 / 3.2 (0.512 / 0.236 / 0.126)
@@@@@: [c N]Lock±up Signal Vave15.0 / 5.0 / 3.2 (0.591 / 0.197 / 0.126)
AX0GE±02

AUTOMATIC TRANSAXLEDIFFERENTIAL ASSEMBLY ±
AX±89
DIFFERENTIAL ASSEMBLY
COMPONENTS
AX0GF±02

AUTOMATIC TRANSAXLEDIFFERENTIAL ASSEMBLY ±
AX±90
DIFFERENTIAL CASE DISASSEMBLY
1. REMOVE RING GEAR
(a) Loosen the staked part of the lock plate.
(b) Remove the 8 bolts and locking plates.
(c) Using a copper hammer, tap on the ring gear to remove
it from the case.
2. REMOVE SIDE BEARINGS
Fasten SST under the bearing above the cutouts on the
speedometer drive gear. Remove the bearing from the
case.
SST 09502±10012
3. CHECK SIDE GEAR BACKLASH
Using a dial gauge, measure the backlash of each side
gear while holding one pinion toward the case.
Standard backlash:
0.05 ± 0.20 mm (0.0020 ± 0.0079 in.)
4. DISASSEMBLE DIFFERENTIAL CASE
(a) Drive out the pinion shaft lock pin from the side on which
the ring gear is installed.
AX0GG±02