W04225
Rack Housing
No.2 Grommet
Rack Housing
No.2 Bracket
Rack Housing
Claw Washer
Rack End Lock NutTie Rod End Rack Boot
ClampClip
Steering Rack
Teflon Ring
Oil Seal
Cylinder End Stopper
Bushing
O±Ring Oil Seal Wire
N´m (kgf´cm, ft´lbf) : Specified touque
Power steering fluid
For use with SST Non±reusable part
Molybdenum disulfide lithium base grease
*
74 (750, 54)
83 (850, 61)
*60 (615, 45)
83 (850, 61)
*60 (615, 45)
74 (750, 54)
O±Ring SR±32
± STEERINGPOWER STEERING GEAR
2127 Author: Date:
On some Toyota models, when Rapgard is removed from the vehicle, a stain is left on the paint
surface. This stain can be seen under the clear coat and is not a defect of the clear coat. The
stain corresponds to a wrinkled area of Rapgard which retained liquids, such as window washer
fluid, that left a discoloration.
REPAIR PROCEDURE:
To remove a stain from a vehicle, heat the stain surface to a temperature of 70 C ± 80 C.
When the stain is removed it will not reappear.
Equipment ±
1. Infrared lamp or dryer to heat the surface.
2. Aluminum foil or a damp cloth to protect plastic parts from deformation.
Procedure ±
1. Apply aluminum foil to adjoining plastic parts or cool with damp cloth periodically.
2. Use an infrared lamp or dryer on the stain developed area and heat for 5 to 10 minutes
at 70 C ± 80 C.
3. After heating for 5 minutes, check whether the stain has disappeared. If the stain still
remains, reheat the area and check again.
NOTE:Take care that the body's paint surface temperature does not become too high.
WARRANTY INFORMATION:
STAINS ON RAPGARD APPLIED AREASPage 1 of 1
AUGUST 9, 1996
BODY
BO008±96
ALL MODELS
OPCODE DESCRIPTION TIME OPN T1 T2
BD6004Remove stains from paint surface
caused by Rapguard0.653301±XXXXX 61 99
Stain
Toyota Supports ASE CertificationPage 1 of 2
BO030-01Title:
WINDSHIELD WIPER BLADE
MAINTENANCE AND CLEANING
Models:
All Models
Technical Service
BULLETIN
December 7, 2001
The following procedures are recommended to maintain windshield wiper blade
performance.
All models.
OP CODEDESCRIPTIONTIMEOPNT1T2
N/ANot Applicable to Warranty±±±±
Recommendations for Windshield Wiper Maintenance, Cleaning and Use:
1. Scheduled Maintenance
Check wiper rubber blades every 4 ± 6 months or 7,500 miles for wear, cracking
and contamination.
Clean glass and rubber wiper blades if blades are not clearing glass adequately.
If this does not correct the problem, then replace the rubber elements.
2. Cleaning Procedure
Wiper Rubber: Bugs, dirt, sap and road grime on blades will cause streaking.
Clean wiper rubber of road and environmental debris using cloth or paper towel
soaked with windshield washer fluid or mild detergent.
DO NOT USE fuel, kerosene, or petroleum based products to clean rubber wiper
blades.
Windshield: Bugs, road grime, sap and car wash wax treatments decrease wiper
performance.
Rinse windshield with water and apply non±abrasive cleaner, such as Bon±Ami
(www.faultless.com), with a sponge.
NOTE:
Make sure to use plenty of water with all powder based cleaners so the glass is
not scratched.
BODY
Introduction
Applicable
Vehicles
Warranty
Information
Maintenance,
Cleaning
and Use
