sensor TOYOTA CAMRY 2000 Service Repair Manual

MX05J±01
Z00295
Z00296
Z00297
Z00298
MX±46
± MANUAL TRANSAXLE (E153)DIFFERENTIAL CASE
1847 Author: Date:
REASSEMBLY
1. ASSEMBLE DIFFERENTIAL CASE
HINT:
Coat all of the sliding and rotating surfaces with gear oil before
reassembly.
(a) Install the thrust washer to the side gear.
(b) Install the 4 pinions and thrust washers to the spider.
(c) Install the side gear and spider with the 4 pinions to the
differential left case.
(d) Using a dial indicator, measure the backlash of the pinion
gear while holding the differential left case.
Standard backlash:
0.05 ± 0.20 mm (0.0020 ± 0.0079 in.)
HINT:
Push the pinion gear and spider with the 4 pinions to the differ-
ential left case.
(e) Install the side gear and spider with the 4 pinions to the
right side of the differential case. Check the side gear
backlash.
(f) Refer to the table below, and select the thrust washer
which will ensure that the backlash is within the specifica-
tion. Try to select a washer of the same size.
Thickness mm (in.)Thickness mm (in.)
0.80 (0.0315)1.20 (0.0472)
0.90 (0.0354)1.30 (0.0512)
1.00 (0.0394)1.40 (0.0551)
1.10 (0.0433)±
(g) Install the vehicle speed sensor drive gear.

± PREPARATIONENGINE MECHANICAL (1MZ±FE)
PP±9
61 Author: Date:
09330±00021Companion Flange Holding ToolCrankshaft pulley
09608±03071ReplacerSpark plug tube gasket
09816±30010Oil Pressure Switch SocketKnock sensor
09843±18020Diagnosis Check Wire
09950±50012Puller C Set
(09951±05010)Hanger 150Crankshaft pulley
Crankshaft timing pulley
(09952±05010)Slide ArmCrankshaft pulley
Crankshaft timing pulley
(09953±05010)Center Bolt 100Crankshaft pulley
Crankshaft timing pulley
(09953±05020)Center Bolt 150Crankshaft pulley
Crankshaft timing pulley
(09954±05010)Claw No.1Crankshaft timing pulley
(09954±05020)Claw No.2Crankshaft pulley
09950±70010Handle Set
(09951±07100)Handle 100Valve guide bushing
Crankshaft rear oil seal

PP1WB±02
± PREPARATIONSFI (5S±FE)
PP±17
69 Author: Date:
SFI (5S±FE)
SST (Special Service Tools)
09268±41047Injection Measuring Tool Set
(09268±41100)ClampExcept California
(09268±41110)Adaptor
(90405±09015)No.1 Union
09268±45014EFI Fuel Pressure Gauge
(09268±41190)Adaptor
(90405±06167)I Union
09631±22020Power Steering Hose Nut
14 x 17 mm Wrench SetFuel line flare nut
09816±30010Oil Pressure Switch SocketKnock sensor 1
09842±30070Wiring ºFº EFI Inspection
09843±18020Diagnosis Check Wire

PP1WW±01
PP±20
± PREPARATIONSFI (1MZ±FE)
72 Author: Date:
SFI (1MZ±FE)
SST (Special Service Tools)
09268±41047Injection Measuring Tool Set
(09268±41100)ClampExcept California
(09268±41300)ClampFor California
09268±41250T Joint
09268±45012EFI Fuel Pressure Gauge
09631±22020Power Steering Hose Nut
14 x 17 mm Wrench SetFuel line flare nut
09817±16011Back±up Light Switch ToolKnock sensor
09842±30070Wiring ºFº EFI Inspection
09843±18020Diagnosis Check Wire

PP1XL±01
± PREPARATIONSUPPLEMENTAL RESTRAINT SYSTEM
PP±99
151 Author: Date:
RECOMMENDED TOOLS
09042±00020Torx Socket T40 .Airbag sensor assembly
09082±00050TOYOTA Electrical Tester Set.
09082±00040TOYOTA Electrical Tester.
(09083±00150)Test Lead SetSeat belt pretensioner connector

± SERVICE SPECIFICATIONSENGINE MECHANICAL (1MZ±FE)
SS±15
178 Author: Date:
No.2 RH engine mounting stay x No.2 Generator bracket6465047
RH engine mounting stay x Water outlet3232023
RH engine mounting stay x Engine moving control rod3232023
RH engine mounting stay x No.2 RH engine mounting bracket3232023
Front engine mounting insulator x Front frame
TMC made
TMMK made Silver color bolt
Green color bolt
80
44
66820
450
67059
32
48
Engine mounting absorber x Front frame4849035
Engine mounting absorber x Transaxle4849035
Rear engine mounting insulator x Front frame6667048
LH engine mounting insulator x Transaxle6465047
PS pump x PS pump bracket4344031
A/C compressor x Housing bracket2525018
A/C compressor x No.1 oil pan2525018
Generator adjusting bar x Drive belt adjusting bar bracket1818513
Main bearing cap x Cylinder block 12 pointed head bolt 1st
2nd
6 pointed head bolt22
Turn 90°
27225
Turn 90°
27516
Turn 90°
20
Connecting rod cap x Connecting rod 1st
2nd24.5
Turn 90°250
Turn 90°18
Turn 90°
Rear oil seal retainer x Cylinder block88069 in.´lbf
EGR cooler x Cylinder block99078 in.´lbf
Engine coolant drain union x Cylinder block3940029
Water seal plate x Cylinder block1818013
Oil filter union x Cylinder block3031022
Water inlet housing x Cylinder block88069 in.´lbf
Knock sensor x Cylinder block3940029
No.2 idler pulley bracket x Cylinder block2829021
A/C compressor housing bracket x Cylinder block2525018
Generator bracket x Cylinder block4344032
Drive plate x Crankshaft8385061
Flywheel x Crankshaft8385061
Front exhaust pipe support bracket x No.1 oil pan2121015
Front exhaust pipe x Exhaust manifold6263046
Front exhaust pipe x Center exhaust pipe5657041
Center exhaust pipe x Tailpipe5657041
Front exhaust pipe bracket x Sub frame3333024
Front exhaust pipe support bracket x Front exhaust pipe stay3333024
Heated oxygen sensor x Center exhaust pipe4445033

SS078±01
± SERVICE SPECIFICATIONSEMISSION CONTROL (1MZ±FE)
SS±17
180 Author: Date:
EMISSION CONTROL (1MZ±FE)
SERVICE DATA
EGR valve
position
sensorResistance (VC ± E2)
Power source voltage (VC± E2)
Power output voltage (EGLS ± E2)
at vacuum (17.3 kPa, 130 mmHg, 5.1 in.Hg)
at no vacuum1.5 ± 4.3 kW
4.5 ± 5.5 V
3.2 ± 5.1 V
0.4 ± 1.6 V

SS079±02
SS±18
± SERVICE SPECIFICATIONSEMISSION CONTROL (1MZ±FE)
181 Author: Date:
TORQUE SPECIFICATION
Part tightenedN´mkgf´cmft´lbf
EGR valve position sensor x EGR valve22017 in.´lbf
EGR pipe x EGR valve121209
EGR pipe x EGR cooler121209
EGR valve x Air intake chamber121209
EGR gas temperature sensor x EGR valve2020014
Front exhaust pipe x Exhaust manifold6263046
Front exhaust pipe x Center exhaust pipe5657041
Front exhaust pipe bracket x Sub frame3333024
Front exhaust pipe support bracket x Front exhaust pipe stay3333024

SS0AG±03
± SERVICE SPECIFICATIONSSFI (5S±FE)
SS±19
182 Author: Date:
SFI (5S±FE)
SERVICE DATA
Fuel pressure
regulatorFuel pressure at no vacuum301 ± 347 kPa (3.1 ± 3.5 kgf/cm2, 44 ± 50 psi)
Fuel pumpResistance at 20°C (68°F)0.2 ± 3.0 W
InjectorResistance at 20°C (68°F)
Injection volume
Difference between each cylinder
Fuel leakage13.4 ± 14.2 W
54 ± 69 cm3 (3.3 ± 4.2 cu in.) per 15 seconds
7 cm3 (0.4 cu in.) or less
One drop or less per minute
Throttle bodyThrottle body fully closed angle
Throttle opener setting speed6°
1,300 ± 1,500 rpm (w/ Cooling fan OFF)
Throttle
position
sensorClearance between stop screw and lever
0 mm (0 in.) VTA ± E2
Throttle valve fully open VTA ± E2
± VC ± E2
0.2 ± 5.7 kW
2.0 ± 10.2 kW
2.5 ± 5.9 kW
IAC valveResistance (+B ± ISCC or ISCO) at cold
at hot17.0 ± 24.5 W
21.5 ± 28.5 W
VSV for EVAPResistance at 20°C (68°F)30 ± 34 W
VSV for vapor
pressure
sensorResistance at 20°C (68°F)33 ± 39 W
VSV for EGRResistance at 20°C (68°F)33 ± 39 W
ECT sensorResistance at ±20°C (±4°F)
at 0°C (32°F)
at 20°C (68°F)
at 40°C (104°F)
at 60°C (140°F)
at 80°C (176°F)10 ± 20 kW
4 ± 7 kW
2 ± 3 kW
0.9 ± 1.3 kW
0.4 ± 0.7 kW
0.2 ± 0.4 kW
IAT sensorResistance at ±20°C (±4°F)
at 0°C (32°F)
at 20°C (68°F)
at 40°C (104°F)
at 60°C (140°F)
at 80°C (176°F)10 ± 20 kW
4 ± 7 kW
2 ± 3 kW
0.9 ± 1.3 kW
0.4 ± 0.7 kW
0.2 ± 0.4 kW
MAP sensorPower source voltage4.5 ± 5.5 V
Vapor Pressure
SensorPower sorce voltage4.5 ± 5.5 V
A/F sensorResistance at 20°C (68°F)0.8 ± 1.4 W
Heated oxygen
sensorResistance at 20°C (68°F)11 ± 16 W
Fuel cut rpmFuel return rpm1,500 rpm

SS0AH±03
SS±20
± SERVICE SPECIFICATIONSSFI (5S±FE)
183 Author: Date:
TORQUE SPECIFICATION
Part tightenedN´mkgf´cmft´lbf
Fuel line
Union bolt type
Flare nut type for use with SST
29
28
300
285
21
21
Fuel pump assembly x Fuel tank44035 in.´lbf
Fuel filter x Fuel pump bracket22017 in.´lbf
Fuel pressure regulator x Fuel pump bracket22017 in.´lbf
Delivery pipe x Cylinder head131309
Fuel tank band x Body3940029
Throttle body x Intake manifold1919514
Knock sensor 1 x Cylinder block4445032
A/F sensor x Exhaust manifold4445032
Oxygen sensor (bank 1 sensor 1) x Exhaust manifold4445032
Oxygen sensor (bank 1 sensor 2) x Front exhaust pipe4445032