fuel pressure TOYOTA CAMRY 2000 Service Repair Manual

1
GENERAL 2000 FEATURES
170EG08
VSV
(for Canister
Closed Valve)VSV
(for
EVAP)
Fuel Tank
Purge Line
Fresh Air LineVapor Pressure
SensorVSV
(for Pressure Switching Valve)
Chacoal Canister
Fresh Air Valve
Drain 2
ENGINE
EVAPORATIVE EMISSION CONTROL SYSTEM
The method for detecting evaporative emission leaks has been changed from the previous internal pressure
monitor type to the vacuum type. The vacuum type forcefully introduces the purge vacuum into the entire
system and a leak is detected by monitoring the transitions in pressure. The changes associated with this sys-
tem are as follows:

A VSV for canister closed valve has been added to the fresh air introduction line.

The 3-way VSV for vapor pressure sensor has been discontinued, and a VSV for pressure switching valve
has been added.

The sensing position of the vapor pressure sensor has been changed from the charcoal canister to the fuel
tank in order to enhance the precision of the vapor pressure sensor.

The fresh air valve characteristics of the charcoal canister have been changed.

Diagnostic trouble codes (DTCs) have been added. For details on the DTCs, refer to the each Repair Manu-
al.

3
CAMRY ± NEW FEATURES
172CM12
Control Valve
Exhaust
Gas: Exhaust Gas Flow (High Engine Speed)
: Exhaust Gas Flow (Low Engine Speed)
35
2-Way Exhaust Control System
A 2-way exhaust control system is used on the TMMK made model. This system reduces the back pressure
by opening and closing a control valve that is enclosed in the main muffler, thus varying the exhaust gas
passage.
The control valve opens steplessly in accordance with the operating condition of the engine, thus enabling
a quieter operation at lower engine speeds, and reducing back pressure at higher engine speeds.
The basic operation is the same as that of the CAMRY SOLARA.
4. Fuel System
Fuel Injector
Along with the discontinuance of the air assist system on the California specification model, 12-hole fuel
injectors with highly atomized injection have been adopted.

CAMRY ± NEW FEATURES36
5S-FNE ENGINE
1. Description
The 5S-FNE engine is a new engine that uses CNG (Compressed Natural Gas) as fuel, which has been devel-
oped based on the 5S-FE gasoline engine.
The main component of natural gas is methane (CH
4), which has fewer carbous (C) than gasoline (mean mo-
lecular formula: C
7.5H13.4). Therefore, the amount of CO2 discharged by this engine is approximately 70%
that of the gasoline engine. Furthermore, this engine achieves low-emission operation by precisely controlled
air-fuel ratio and using special catalysts for the CNG application.
However, because the fuel is in the gaseous form, its volumetric efficiency is low, causing lower power output
if this fuel is used in the base engine.
Therefore, the 5S-FNE engine has adopted the following features: a high compression ratio, the intake valves
with early closed timing, the intake and exhaust valves with increased lift, a low back pressure muffler made
possible by the 2-way exhaust system, injectors for gaseous fuel, and a catalytic converter designed exclu-
sively for CNG application. At the same time, precision air-fuel ratio control is effected through the use of
the air-fuel ratio sensor* and the heater oxygen sensor, thus achieving the level of performance that is equiva-
lent to the base engine. Moreover, this engine realizes extremely low emissions and restoring engine torque.
*: Already adopted on the California specification 5S-FE engine.

Specifications 
Item5S-FNE Engine5S-FE Engine
No. of Cyls. & Arrangement4-Cylinder, In-Line
Valve Mechanism16-Valve DOHC,
Belt & Gear Drive
Combustion CamberPentroof Type
ManifoldsCross-Flow
Fuel SystemSFI
Displacement cm3 (cu.in.)2164 (312.0)
Bore x Stroke mm (in.)87.0 x 91.0 (3.43 x 3.58)
Compression Ratio11.0 : 19.5 : 1
Max. Output [SAE-NET]88 kW @ 5200 rpm
(118 HP @ 5200 rpm)
101 kW @ 5200 rpm
(136 HP @ 5200 rpm)
97 kW @ 5200 rpm*
(133 HP @ 5200 rpm)*
Max. Torque [SAE-NET]178 N.m @ 2400 rpm
(131 ft-lbf @ 2400 rpm)
203 N.m @ 4400 rpm
(150 ft-lbf @ 4400 rpm)
201 N
.m @ 4400 rpm*
(148 ft-lbf @ 4400 rpm)*
IntakeOpen3 BTDC
Valve
IntakeClose38 ABDC43 ABDCValve
Timing
ExhaustOpen45 BBDCExhaustClose3 AT D C
Fuel Octane Number RON13091
Oil GradeAPI SJ EC or ILSAC
*: California Specification Models

CAMRY ± NEW FEATURES 38
2. Features of 5S-FNE Engine
Features of the 5S-FNE engine are listed below.
Item
Features
Performance
High compression ratio is used.
High lift camshaft is used.
Low back pressure muffler is used.
Fuel Economy
High compression ratio is used.
Valve spring load has been reduced.
Low-friction. TiN (titanium nitride) coated valve lifters has been adopted.
Low Emission
A fuel injection system containing gas injectors has been adopted.
Because the fuel is in the gaseous state, it does not come in contact with
the wall surface, making optimal air-fuel ratio control possible
immediately after the engine has been started.
Precision air-fuel ratio feedback control that uses an air-fuel ratio sensor
and a heated oxygen sensor has been adopted.
Two catalytic converters designed exclusively for the natural gas engine
have been adopted: the WU-TWC (Warm Up Three-Way Catalytic
Converter) and the TWC (Three-Way Catalytic Converter).
Other Features
Highly rigid pistons have been adopted to accommodate the high
compression ratio.
A CNG (Compressed Natural Gas) pressure regulator that precisely
regulates the CNG has been adopted.
A large-bore delivery pipe and fuel hose with minimal internal conduit
resistance have been adopted.
The electro magnetic fuel shutoff valve is added on the delivery pipe.
A fuel pressure sensor that corrects the fuel injection volume and a fuel
temperature sensor have been provided on the delivery pipe.
The starting performance of the engine at low temperatures has been
ensured by increasing the volume of the airflow of the IAC (Idle Air
Control).
Materials that excel in wear resistance have been adopted on the valves
and valve seats for both the intake and exhaust.
Rust-resistant spark plugs have been adopted.
Aluminum lining and carbon fiber have been adopted in the fuel tank.
For the fuel gauge, a fuel tank fuel temperature sensor and a fuel pipe fuel
pressure sensor have been adopted.

3
CAMRY ± NEW FEATURES
172CM14
Fuel
Pressure
SensorFuel Temp.
SensorFuel
Pressure
RegulatorFuel Shutoff ValveFuel Tank
Fuel Shutoff ValveRelief Valve
Inlet Check
Valve
Fuel Temp.
Sensor
Coupler
Tank Valve Assembly
Vent Tube Manual
Shutoff
Valve Oil
Separator
Fuel Shutoff Valve Injectors
Delivery Pipe Discharge
ValveFuel
Pressure
SensorFuel
Filter43
6. Fuel System
General
The compressed gas [maximum pressure approximately 250 kg / cm
2 (3600 psi, 24.8 MPa) @ 21C
(70F)] from the CNG fuel tank located in the rear section of the vehicle is routed via a fuel filter to the
engine compartment. The pressure of the fuel is then reduced to 8 kg / cm
2 (114 psi, 785 kPa).
A pressure regulator and injectors designed exclusively for CNG application have been adopted.
A fuel pressure sensor and a fuel temperature sensor that are used for the correction of the fuel injection
volume are located on the delivery pipe.
The fuel tank, pressure regulator, and the delivery pipe are provided with shutoff valves that shut off the
fuel when the ignition switch is turned OFF.
In addition, these valves shut off the fuel when the engine stalls, the SRS airbag is deployed, or the pres-
sure in the main pipe becomes abnormally low.
A fuel temperature sensor for the fuel gauge is mounted on the tank valve assembly, and a fuel pressure
sensor is mounted immediately upstream of the pressure regulator.

Fuel System Diagram 

CAMRY ± NEW FEATURES
167CN08
Tank Valve
AssemblyTank Band
Coil Springs
167CN26
Tank Valve AssemblyFuel
Temperature
Sensor 44
Fuel Tank
A fuel tank made with carbon fiber and alumi-
num lining has been adopted to prevent weight
increase.
Because the fuel tank expands along with the
increase in the pressure of the compressed gas,
the tank bands contain coil springs to accom-
modate the fluctuation in the perimeter of the
tank.
The fuel tank is provided with a tank valve as-
sembly.
Tank Valve Assembly
1) General
The tank valve assembly is mounted on the
tank and consists of a fuel shutoff valve, inlet
check valve, relief valve and two manual cut-
off valves.

3
CAMRY ± NEW FEATURES
172CM17
CloseOpen45
2) Fuel Shutoff Valve for Fuel Tank
This valve uses an solenoid valve. The main pipe that supplies compressed gas to the engine is connected
to this valve, which opens when the ignition switch is turned ON. If the engine stalls, this valve automati-
cally shuts off the fuel even if the ignition switch is turned ON. The valve reopens upon restarting the
engine.
Also, this valve shuts off the fuel if the SRS airbag is deployed in a collision or if the pressure in the main
pipe becomes abnormally low.
3) Inlet Check Valve
Connected to a filler pipe that guides the fuel that fills through the coupler, the inlet check valve shuts
off by the force of a spring and by the pressure of the gas in the tank.
During filling, the pressure of the filling gas opens the inlet check valve.
4) Relief Valve
A vent tube is connected to this valve.
If the fuel tank is exposed to an abnormally high temperature, this valve opens (by melting) to discharge
the CNG at a predetermined temperature, thus helping prevent the fuel tank from bursting due to the in-
crease in gas pressure.
The discharged CNG is guided under the floor through a vent tube and is released outside of the vehicle.
Coupler
The coupler allows the fuel to be filled when it is connected with a fuel filling nozzle. The coupler has a
built-in check valve to help prevent the CNG from flowing backward.
Manual Shutoff Valve
This valve is mounted below the vehicle floor.
When servicing the vehicle, this valve can be
manually turned 90 degrees to shut off the main
pipe.

CAMRY ± NEW FEATURES
167CN10
172CM15
Fuel
Shutoff
Valve
Water Passage
Oil SeparatorRelief Valve 46
Fuel Filter
Mounted below the vehicle floor, the fuel filter
removes any moisture or oil from the fuel.
Fuel Pressure Regulator
The fuel pressure regulator regulates the fuel pressure by reducing the pressure of the compressed natural
gas from the fuel tank to the fuel injection pressure, which is 8 kg / cm
2 (114 psi, 785 kPa).
Similar to the fuel shutoff valve for the fuel tank, a fuel shutoff valve is provided on the fuel inlet side
of the fuel pressure regulator to shut off the supply of fuel when the engine is stopped or during abnormal
conditions.
An oil separator that traps the moisture and oil in the fuel is provided on the low pressure side.
A built-in relief valve is provided to protect the parts located on the low pressure side.
While the fuel pressure is being reduced by the fuel pressure regulator, the Joule-Thomson effect
associated with the expansion of the gas causes the fuel pressure regulator to be cooled excessively, exert-
ing unfavorable influence on the rubber parts such as diaphragms and fuel hoses.
Therefore, to raise the gas temperature, a water passage is provided in the fuel pressure regulator to allow
the engine coolant to warm the regulator.

3
CAMRY ± NEW FEATURES
172CM13
Discharge
ValveFuel Pressure Sensor
Fuel Temp. SensorDelivery Pipe
CNG
Fuel Shutoff
Valve
Injector
167CN23
Rubber Sheet47
Delivery Pipe
A delivery pipe with a wide passage that enables a large volume of gas to flow responsively has been
adopted to minimize the pressure loss.
A fuel pressure sensor and a fuel temperature sensor that help correct the fuel injection volume are
mounted on the delivery pipe.
Similar to the fuel shutoff valves for the fuel tank and the fuel pressure regulator, a fuel shutoff valve is
provided on the fuel inlet side of the delivery pipe to shut off the supply of fuel when the engine is stopped
or during abnormal conditions.
To discharge the fuel out of the delivery pipe during service, a discharge valve is provided.
Injector
For the injection of fuel in the gaseous state, injectors that allow the flow of a large volume of fuel and pro-
vide improved sealing performance have been adopted.

CAMRY ± NEW FEATURES
172CM16
: Plating Area
Platinum Tip
48
Fuel Temperature and Pressure Sensor for Fuel Gage
A fuel temperature sensor that detects the temperature in the fuel tank is provided on the tank valve assem-
bly.
A fuel pressure sensor that detects the pressure in the fuel main pipe is provided immediately upstream of
the fuel pressure regulator.
The pressure and the temperature of the fuel are detected by these sensors and are input into the ECM.
These values are then converted by the ECM into the equivalent pressure at 21C to actuate the fuel gauge.
7. Ignition System
Because the spark plugs are susceptible to rust when used with natural gas, corrosion-resistant spark plugs
have been adopted. These spark plugs are the platinum-tipped spark plugs that have their metallic portion
plated.

Recommended Spark Plug 
DENSOPK20TR8-G
Plug Gap0.8 ± 1.0 mm (0.031 ± 0.39 in.)