oil level TOYOTA CAMRY 2000 Service Repair Manual

CAMRY ± NEW FEATURES36
5S-FNE ENGINE
1. Description
The 5S-FNE engine is a new engine that uses CNG (Compressed Natural Gas) as fuel, which has been devel-
oped based on the 5S-FE gasoline engine.
The main component of natural gas is methane (CH
4), which has fewer carbous (C) than gasoline (mean mo-
lecular formula: C
7.5H13.4). Therefore, the amount of CO2 discharged by this engine is approximately 70%
that of the gasoline engine. Furthermore, this engine achieves low-emission operation by precisely controlled
air-fuel ratio and using special catalysts for the CNG application.
However, because the fuel is in the gaseous form, its volumetric efficiency is low, causing lower power output
if this fuel is used in the base engine.
Therefore, the 5S-FNE engine has adopted the following features: a high compression ratio, the intake valves
with early closed timing, the intake and exhaust valves with increased lift, a low back pressure muffler made
possible by the 2-way exhaust system, injectors for gaseous fuel, and a catalytic converter designed exclu-
sively for CNG application. At the same time, precision air-fuel ratio control is effected through the use of
the air-fuel ratio sensor* and the heater oxygen sensor, thus achieving the level of performance that is equiva-
lent to the base engine. Moreover, this engine realizes extremely low emissions and restoring engine torque.
*: Already adopted on the California specification 5S-FE engine.

Specifications 
Item5S-FNE Engine5S-FE Engine
No. of Cyls. & Arrangement4-Cylinder, In-Line
Valve Mechanism16-Valve DOHC,
Belt & Gear Drive
Combustion CamberPentroof Type
ManifoldsCross-Flow
Fuel SystemSFI
Displacement cm3 (cu.in.)2164 (312.0)
Bore x Stroke mm (in.)87.0 x 91.0 (3.43 x 3.58)
Compression Ratio11.0 : 19.5 : 1
Max. Output [SAE-NET]88 kW @ 5200 rpm
(118 HP @ 5200 rpm)
101 kW @ 5200 rpm
(136 HP @ 5200 rpm)
97 kW @ 5200 rpm*
(133 HP @ 5200 rpm)*
Max. Torque [SAE-NET]178 N.m @ 2400 rpm
(131 ft-lbf @ 2400 rpm)
203 N.m @ 4400 rpm
(150 ft-lbf @ 4400 rpm)
201 N
.m @ 4400 rpm*
(148 ft-lbf @ 4400 rpm)*
IntakeOpen3 BTDC
Valve
IntakeClose38 ABDC43 ABDCValve
Timing
ExhaustOpen45 BBDCExhaustClose3 AT D C
Fuel Octane Number RON13091
Oil GradeAPI SJ EC or ILSAC
*: California Specification Models

3
CAMRY ± NEW FEATURES49
8. Engine Control System
General
An engine control system based on the 5S-FE engine has been adopted. The knock sensor has been discon-
tinued because natural gas has a high octane value and is less susceptible to knocking.
The engine control system of 5S-FNE and 5S-FE engines are compared below.
System
Outline5S-FNE5S-FE
SFI
Se
quential
A D-type SFI system is used, which indirectly detects
intake air volume by manifold absolute pressure sensor.Sequential
Multiport Fuel
InjectionThe fuel injection system is a sequential multiport fuel
injection system.
Ignition timing is determined by the ECM based on
signals from various sensors.
ESA
Electronic Spark
AdvanceThe ECM corrects the ignition timing in response to
engine knocking in accordance with the signals
received from the knock sensor.
Ð
dva ce
Torque control correction during gear shifting had been
used to minimize the shift shock.*1
IAC
(Idle Air Control)A rotary solenoid type IAC valve controls the fast idle
and idle speeds.(1-Coil Type
Built-in Driver)(2-Coil Type)
Fuel Pump ControlFuel pump operation is controlled by signal from the
ECM.Ð
Fuel Cut-Off
Control
The fuel shutoff valves for the fuel tank, fuel pressure
regulator, and delivery pipe are shut off to stop the
supply of fuel when the ignition switch is turned OFF or
during abnormal conditions (such as engine stalling,
SRS airbag deployed, etc.).
Ð
Injector ControlPrevents the frozen stuck of the injector to ensure the
startability of the engine at low temperature.Ð
Oxygen Sensor
and Air Fuel Ratio
Sensor
Heater ControlMaintains the temperature of the oxygen sensor and air
fuel ratio sensor at an appropriate level to increase
accuracy of detection of the oxygen concentration in the
exhaust gas.
*2
EGR Cut-Off
ControlCuts off EGR according to the engine condition to
maintain drivability of the vehicle and durability of the
EGR components.

Evaporative
Emission ControlThe ECM controls the purge flow of evaporative
emissions (HC) in the charcoal canister in accordance
with engine conditions.
Ð
Air Conditioning
Cut-Off ControlBy turning the air conditioning compressor ON or OFF
in accordance with the engine condition, drivability is
maintained.
*3*3
Diagnosis
When the ECM detects a malfunction, the ECM
diagnoses and memorized the failed section.
DiagnosisThe diagnosis system includes a function that detects a
malfunction in the evaporative emission control system.Ð
Fail-Safe
When the ECM detects a malfunction, the ECM stops or
controls the engine according to the data already stored
in memory.

*1: Only for Automatic Transaxle Model
*
2: Air fuel ratio sensor only for California specification model
*
3: The air conditioning magnet clutch controled by the ECM

CAMRY ± NEW FEATURES
No.4 INJECTOR
SPARK PLUGSIGNITERS and
IGNITION COILS
No.2 INJECTOR
No.1 INJECTOR
No.3 INJECTOR
SENSORS ACTUATORS
MANIFOLD ABSOLUTE
PRESSURE SENSORSFI PIM#10+
CRANKSHAFT POSITION
SENSORNE
CAMSHAFT POSITION
SENSORG
ENGINE COOLANT TEMP.
SENSORTHW
INTAKE AIR TEMP. SENSORTHA
THROTTLE POSITION SENSORVTA
COMBINATION METER
SPD
Vehicle Speed Signal
AIR FUEL RATIO SENSOR
(Bank 1, Sensor 1)AF
HEATED OXYGEN SENSOR
(Bank 1, Sensor 2)OX2
POWER STEERING OIL
PRESSER SWITCHPSW
TAILLIGHT & REAR WINDOW
DEFOGGER SYSTEMELS
IGNITION SWITCHSTA
PARK / NEUTRAL POSITION
SWITCHNSW
STOP LIGHT SWITCHSTP
AIRBAG SENSOR ASSEMBLY
F/PS
Fuel Cut-Off Signal
#10
#20+
#20
#30+
#30
#40+
#40
ESA
IGT1,
IGT2
IGF
CONTROL VALVEIACRSD
VSV EGREGR
AIR FUEL RATIO SENSOR
HEATER AIR FUEL RATIO SENSOR
HEATER CONTROLHTAF
HEATED OXYGEN SENSOR
HEATER OXYGEN SENSOR HEATER
CONTROLHT2
MAGNET CLUTCH RERAYAIRE CONDITIONING
CUT-OFF CONTROLMGC
FUEL GAGE
LOW FUEL LEVEL WARNING
LIGHT
ECM
AIR CONDITIONING SWITCHA/C SW
R, 2, L
FUEL
FUEL W
50
Construction
The configuration of the engine control system in the 5S-FNE engine is as shown in the following chart.
(Continued)

ENGINE OIL INSPECTION
1. CHECK OIL QUALITY
Check the oil for deterioration, entry of water, dis±
coloring or thinning.
If oil quality is visibly poor, replace it.
Oil grade:
API grade SG or SH, Energy Conserving II multi±
grade engine oil or ILSAC multigrade engine oil.
Recommended viscosity is as shown in the illustra±
tion.
TUNE±UP
ENGINE COOLANT INSPECTION
1. CHECK ENGINE COOLANT LEVEL AT RESERVOIR
TANK
The engine coolant level should be between the
ªLOWº and ªFULLº lines at low temperature.
If low, check for leaks and add engine coolant up to
the ªFULLº
2. CHECK ENGINE COOLANT QUALITY
There should be no excessive deposits of rust or
scales around the radiator cap or radiator filler hole,
and the engine coolant should be free from oil.
If excessively dirty, replace the engine coolant.
2. CHECK ENGINE OIL LEVEL
The oil level should be between the ªLº and ªFº marks
on the dipstick.
If low, check for leakage and add oil up to the ªFº
mark.
± 5S±FE ENGINEENGINE MECHANICALEG1±8

(b) Secure the exhaust camshaft sub gear to drive gear
with a service bolt.
Recommended service bolt:
Thread diameter6 mm
Thread pitch 1.0 mm
Bolt length 16±20 m m (0.63±0.79 in.)
HINT: When removing the camshaft, make sure that
the torsional spring force of the sub gear has been
eliminated by the above operation. 35. REMOVE CAMSHAFTS
NOTICE: Since the thrust clearance of the camshaft is
small, the camshaft must be kept level while it is being
removed. If the camshaft is not kept level, the portion of
the cylinder head receiving the shaft thrust may crack or
be damaged, causing the camshaft to seize or break. To
avoid this, the following steps should be carried out.
A. Remove exhaust camshaft
(a) Set the knock pin of the intake camshaft at 10±455
BTDC of camshaft position.
HINT: The above angle allows No.2 and No.4 cylinder
cam lobes of the exhaust camshaft to push their valve
lifters evenly.HINT: Arrange the grommets in correct order, so that
they can be reinstalled into their original positions.
This minimizes any possibility of oil leakage due to
reuse of grommets.
34. REMOVE HIGH ± TENSION CORDS CLAMP AND
PCV VALVE
± 5S±FE ENGINEENGINE MECHANICALEG1±50

(e) Alternately loosen and remove the 2 bolts on the No.
2 bearing cap.
HINT:
wAs the 2 No.2 bearing cap bolts are loosened, make
sure that the camshaft is lifted out straight and level,
after breaking adhesion on the front bearing cap.
wIf the camshaft is not being lifted out straight and
level, retighten the 2 No.2 bearing cap bolts. Reverse
the order of above steps from (e) to (a) and reset the
knock pin of the intake camshaft at 80±115*6TDC,
and repeat steps from (b) to (e) once again.
NOTICE: Do not pry on or attempt to force the camshaft
with a tool or other object.
(f) Remove the No.2 bearing cap and camshaft. (c) Uniformly loosen and remove the6 bolts on the No.1,
No.3 and No.4 bearing caps in several passes in the
sequence shown.
NOTICE: Do not remove the No.2 bearing cap bolts at this
stage.
(d) Remove the No. 1, No.3 and No.4 bearing caps.
36. DISASSEMBLE EXHAUST CAMSHAFT
(a) Mount the hexagon wrench head portion of the cam±
shaft in a vise.
NOTICE: Be careful not to damage the camshaft.
(b) Remove the 2 bolts, front bearing cap and oil seal.
± 5S±FE ENGINEENGINE MECHANICALEG1±52

37. A/T:
CONNECT AND ADJUST THROTTLE CABLE
38. CONNECT AND ADJUST ACCELERATOR CABLE
39. FILL WITH ENGINE COOLANT
Capacity:
6.3 liters (6.7 US qts, 5.5 Imp. qts)
40. CONNECT NEGATIVE (±) TERMINAL CABLE TO
BATTERY
41. START ENGINE AND CHECK FOR LEAKS
42. ADJUST IGNITION TIMING
(See page IG ±19 and 38)
Ignition timing:
10
BTDC @ idle
(w/ Terminals TO and E1 connected)
43. PERFORM ROAD TEST
Check for abnormal noise, shock, slippage, correct shift
points and smooth operation.
44. RECHECK ENGINE COOLANT LEVEL AND OIL
LEVEL
± 5S±FE ENGINEENGINE MECHANICALEG1±82

27. INSTALL AIR CLEANER ASSEMBLY, RESONATOR
AND AIR CLEANER HOSE
(a) Install the air cleaner case with 3 bolts.
(b) Install the element.
(c) Connect the air cleaner hose to the throttle body.
(d) Install the air cleaner cap together with the resonator
and air cleaner hose.
(e) California only:
Connect the air hose to the air cleaner hose.
(f) Connect the intake air temperature sensor connector.
28. A/T:
CONNECT AND ADJUST THROTTLE CABLE
29. CONNECT AND ADJUST ACCELERATOR CABLE
30. FILL WITH ENGINE COOLANT
31. FILL WITH ENGINE OIL
32. CONNECT NEGATIVE (±) TERMINAL CABLE TO
BATTERY
33. START ENGINE AND CHECK FOR LEAKS
34. PREFORM ENGINE ADJUSTMENT
35. INSTALL ENGINE UNDER COVERS
36. INSTALL HOOD
37. PERFORM ROAD TEST
Check for abnormal noises, shock, slippage, correct
shift points and smooth operation.
38. RECHECK ENGINE COOLANT AND ENGINE OIL
LEVELS26. w/ CRUISE CONTROL SYSTEM:
INSTALL CRUISE CONTROL ACTUATOR
(a) Install the actuator and bracket with the 3 bolts.
(b) Connect the actuator connector.
(c) Install the actuator cover.(6) Data link connector 1
(7) 2 ground straps from RH fender apron
(e) Connect the MAP sensor connector.
25. INSTALL RADIATOR
± 5S±FE ENGINEENGINE MECHANICALEG1±133

RADIATOR
The radiator performs the function of cooling the coolant which has passed through the water
jacket and become hot, and it is mounted in the front of the vehicle. The radiator consists of an
upper tank and lower tank, and a core which connects the two tanks. The upper tank contains the
inlet for coolant from the water jacket and the filler inlet. It also has a hose attached through
which excess coolant or steam can flow. The lower tank has an outlet and drain cock for the
coolant. The core contains many tubes through which coolant flows from the upper tank to the
lower tank as well as to cooling fins which radiate heat away from the coolant in the tubes. The
air sucked through the radiator by the electric fan, as well as the wind generated by the vehicle's
travel, passes through the radiator, cooling the coolant. Models with automatic transmission
include an automatic transmission fluid cooler built into the lower tank of the radiator. A fan with
an electric motor is mounted behind the radiator to assist the flow of air through the radiator. The
fan operates when the engine coolant temperature becomes high in order to prevent it from be-
coming too high.
RADIATOR CAP
The radiator cap is a pressure type cap which seals the radiator, resulting in pressurization of the
radiator as the coolant expands. The pressurization prevents the coolant from boiling even when
the engine coolant temperature exceeds 100°C (212°F). A relief valve (pressurization valve) and a
vacuum valve (negative pressure valve) are built into the radiator cap. The relief valve opens and
lets steam escape through the overflow pipe when the pressure generated inside the cooling sys-
tem exceeds the limit (coolant temperature: 110±120°C (230±248°F), pressure; 58.8103.0 kpa
(0.6±1.05 kgf/cm
2, 8.5±14.9 psi). The vacuum valve opens to alleviate the vacuum which develops
in the cooling system after the engine is stopped and the engine coolant temperature drops. The
valve's opening allows the coolant in the reservoir tank to return to the cooling system.
RESERVOIR TANK
The reservoir tank is used to catch coolant which overflows from the cooling system as a result
of volumetric expansion when the coolant is heated. The coolant in the reservoir tank returns to
the radiator when the coolant temperature drops, thus keeping the radiator full at all times and
avoiding needless coolant loss.
Check the reservoir tank level to learn if the coolant needs to be replenished.
WATER PUMP
The water pump is used for forced circulation of coolant through the cooling system. It is
mounted on the front of the cylinder block and driven by a timing belt.
THERMOSTAT
The thermostat has a wax type bypass valve and is mounted in the water inlet housing. The
thermostat includes a type of automatic valve operated by fluctuations in the engine coolant
temperature. This valve closes when the engine coolant temperature drops, preventing the
circulation of coolant through the engine and thus permitting the engine to warm up rapidly. The
valve opens when the engine coolant temperature has risen, allowing the circulation of coolant.
Wax inside the thermostat expands when heated and contracts when cooled. Heating the wax
thus generates pressure which overpowers the force of the spring which keeps the valve closed,
thus opening the valve. When the wax cools, its contraction allows the force of the spring to take
effect once more, closing the valve. The thermostat in this engine operates at a temperature of
82
C (180
F).
± 5S±FE ENGINECOOLING SYSTEMEG1±239

2. CHECK ENGINE COOLANT QUALITY
There should not be any excessive deposits of rust or
scales around the radiator cap or radiator filler hole,
and the engine coolant should be free from oil.
If excessively dirty, replace the engine coolant.
3. REPLACE ENGINE COOLANT
(a) Remove the radiator cap.
CAUTION: To avoid the danger of being burned, do not
remove It while the engine and radiator are still hot, as
fluid and steam can be blown out under pressure.
(b) Drain the engine coolant from the radiator drain cock
and engine drain plug. (Engine drain plug at the right
rear of cylinder block.)
(c) Close the drain cock and plug.
Torque (Engine drain plug):
13 N±m (130 kgf±cm, 9 ft±lbf)
(d) Slowly fill the system with coolant.
Use a good brand of ethylene±glycol base
coolant and mix it according to the
manufacturer 's directions.
Using engine coolant which includes more than
5096 ethylene±glycol (but not more than 7096) is
recommended.
NOTICE:
wDo not use a alcohol type coolant.
wThe engine coolant should be mixed with demineral±
ized water or distilled water.
Capacity (w/ Heater):
8.3 liters (6.7 US qts, 5.5 Imp.qts)
(a) Reinstall the radiator cap.
(f) Warm up the engine and check for leaks.
(g) Recheck the engine coolant level and refill as neces±
sary.
COOLANT CHECK AND
REPLACEMENT
1. CHECK ENGINE COOLANT LEVEL AT RESERVOIR
TANK
The engine coolant level should be between the
ºLOWº and ªFULLº lines.
If low, check for leaks and add engine coolant up to
the ªFULLº line.
± 5S±FE ENGINECOOLING SYSTEMEG1±241